Dell EqualLogic PS4000 Bedienungsanleitung

PS4000 Storage Arrays

Rack Mount Instructions

Part Number: F464T Rev. A00

Dell is a trademark of Dell, Inc.

EqualLogic is a registered trademark.

All trademarks and registered trademarks mentioned herein are the property of their respective owners.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell is strictly forbidden.

April 2009

PS4000 Rack Mount Instructions

PS4000 Rack Mount Instructions iii

Table of Contents

Introduction......................................................................................................................................1

Before You Begin............................................................................................................................1

Installation Safety Precautions...................................................................................................1

Installation Environmental Requirements..................................................................................1

Rack Requirements....................................................................................................................2

Rail Kit Parts..............................................................................................................................3

Tool Requirements.....................................................................................................................4

Steps for Mounting an Array in a Rack...........................................................................................4

Step 1: Change the Mounting Rail Hardware............................................................................4

Step 2: Determine Where to Place the Mounting Rails in the Rack..........................................5

Step 3: Attach the Mounting Rails to the Rack Poles................................................................5

Step 4: Slide the Chassis into the Rack......................................................................................7

Step 5: Attach the Chassis to the Mounting Rails......................................................................8

Step 6: Install the Bezel .............................................................................................................9

Where to Go Next..........................................................................................................................10

Technical Support..........................................................................................................................10

Introduction

For proper operation, a PS4000 storage array must be installed in a rack. See your PS Series support

provider for information about supported racks.

Before You Begin

Before you begin to mount an array in a rack, you must:

•Read the installation safety precautions. See Installation Safety Precautions.

•Make sure the rack location meets the array’s environmental requirements. See Installation

Environmental Requirements.

•Make sure your rack meets the rack requirements. See Rack Requirements.

•Unpack the rail kit and make sure you have all the necessary parts and tools. The rail kit is located in

the array shipping box. You must supply your own tools. See Rail Kit Parts and Tool Requirements.

Installation Safety Precautions

Follow these safety precautions:

•It is recommended that only individuals with rack mounting experience install a PS4000 array in a

rack.

•Make sure the array is fully grounded at all times to prevent damage from electrostatic discharge.

•When handling the array hardware, you must use the electrostatic wrist guard shipped with the array

or a similar form of protection.

•You need at least two people to lift the array chassis from the shipping box.

Installation Environmental Requirements

The rack location must meet the following environmental requirements:

•Only operate an enclosure from a power source with a voltage range of 100 to 240 VAC.

•Make sure your power source has sufficient electrical overload protection.

•In North America, connect the enclosure to a source of power with over-current protection provided

by a double pole 20A or less device (UL 489 circuit breakers). In Europe, the over-current protection

must be provided by a 20A or less device (IEC circuit breakers).

•Make sure there is sufficient space for air flow in front of and behind the array.

•Make sure the location is properly vented.

•Make sure the rack installation meets the array technical specifications in Table 1.

PS4000 Rack Mount Instructions 1

Table 1: PS4000 Array Specifications

Specification Value

Weight of fully loaded array 35 kg (77.6 lb)

Operating temperature 5 to 35 °C (41 to 95 °F)

Storage temperature -30 to 60 °C (-22 to 140 °F)

Maximum operating altitude 3048 meters (10,000 feet)

Operational relative humidity 20% to 80% noncondensing

Storage relative humidity 5% to 80% noncondensing

Thermal output (fully-loaded array) 1700 BTU/hour (SAS disks)

1550 BTU/hour (SATA disks)

Operational shock 5gpeak 1/2 sin, for 10ms

Operational vibration .21 Grms 5 to 500 Hz Random

Input voltage 100 to 240 VAC (auto-sensing)

Input frequency 48 – 62 Hz

System input power 530 VA (maximum)

Each power supply 450 watts DC output

Maximum input power: 0.7 KVA

Input current: 7 – 3.5A

Chassis dimensions 13 cm by 48.26 cm by 55.1 cm

(5.12 in. by 19 in. by 21.7 in.)

Rack Requirements

Make sure the rack and the array installation meet the following requirements:

•Use an industry-standard (for example, CEA-310-E), four-pole, 19 inch (48.3 cm) rack.

•The rack must be rated for 540 kg (1200 pounds) static load or greater.

•The minimum rack depth is 100 cm (40 inches) from the front of the rack to the rear of the rack.

•The distance between the inside of the front and rear rack poles (the mounting surfaces) must be

61 cm (24 inches) to 90 cm (36 inches).

•Secure the rack to the floor for added stability.

•Load a rack with arrays from the bottom to the top.

•There must be at least 4.1 cm (1.6 inches) between the rack door and the front of the array to

accommodate the array front bezel.

•The rack (with installed arrays) must meet the safety requirements of UL 60950-1 and IEC 60950-1.

•Mount the array in a horizontal position, or you will void your array warranty and support contract.

2PS4000 Rack Mount Instructions

Rail Kit Parts

The rail kit includes the parts described in Table 2. Not all parts are used in all racks.

•Parts for round racks are included in bag labeled ROUND.

•Parts used in multiple racks are included in the bag labeled COMMON.

•No additional parts are required for tapped racks.

Table 2: Rail Kit Parts (Images Not to Scale)

Item Graphic Quantity Description

1 each LH Rail Assembly

RH Rail Assembly

2 M5 x 8 Posi pan head screw

with patchlock (COMMON bag)

4 Large O/D plain washer

(COMMON bag)

4 Spring washer (COMMON bag)

4 #10-32 x 25 Phillips head NO2

pan head screw (COMMON

bag)

7 8 Locator pins for round hole rack

(ROUND bag)

Tool Requirements

You need the following tools to mount an array in a rack. These tools are not provided in the array

shipping box.

•#2 Phillips screwdriver

•#2 pozidriv® screwdriver

•(Optional) Torque wrench. The torque specification for the supplied screws is 5.69 N m (4.2 foot

pounds).

PS4000 Rack Mount Instructions 3

Steps for Mounting an Array in a Rack

Follow these steps to mount a PS4000 array in a rack:

1. Change the mounting rail hardware, if necessary.

2. Determine where to place the mounting rails in the rack.

3. Attach the mounting rails to the rack.

4. Slide the chassis into the rack.

5. Attach the chassis to the brackets on the mounting rails and to the front of the mounting rails.

6. Install the bezel.

These steps are described in detail in the following sections. After you mount the array in the rack, see the

Installation and Setup manual for information about completing the array hardware installation.

Step 1: Change the Mounting Rail Hardware

The mounting rails are shipped with hardware pre-installed for mounting in a rack with square holes. If

you have a square-hole rack, no changes are necessary. Proceed with Step 2: Determine Where to Place

the Mounting Rails in the Rack.

If your rack has round or tapped holes, change the hardware as follows.

•For round hole racks:

- On the front and back of both mounting rails, remove the pre-installed locator pins and replace

them with the locator pins from the bag labeled ROUND. Insert the locator pins from the front,

using the same orientation as the pre-installed pins.

•For tapped hole racks:

1. On the front and back of both mounting rails, remove the pre-installed locator pins.

2. Re-install the same locator pins from the opposite side of the holes you removed them from, so

that the pin protrudes from the front and rear of the mounting rail flanges.

Step 2: Determine Where to Place the Mounting Rails in the Rack

Make sure there is enough space in the rack for a 3U chassis. In a standard rack, the height of a 3U

chassis will span 9 holes.

Figure 1 shows the location of the top and bottom of the chassis relative to the location of the screws used

to attach the rail and the array to the rack’s front right and left poles.

4PS4000 Rack Mount Instructions

Figure 1 Front Pole Screw Locations

Figure 1 Description

Indicates the top of the PS4000 array chassis.

Location of the upper mounting rail screw.

Location of the captive chassis thumbscrew (between the two locator pins).

Indicates the bottom of the PS4000 array chassis. The array rests on the lip of the mounting rails.

Step 3: Attach the Mounting Rails to the Rack Poles

The rail kit includes two mounting rails, one for the left rack pole and one for the right rack pole when

viewed from the front of the rack.

Guidelines for Attaching the Mounting Rails

Follow these guidelines when attaching the mounting rails to the rack poles:

•Attach the mounting rail flanges to the inside of the rack pole flanges.

•Insert the screws from the outside of the rack.

•Use the markings on the rack poles (if present) to make sure the rails are level, or use a level.

Attaching the Mounting Rails to the Rack Poles

To attach the mounting rails to the rack poles:

1. Collect the necessary hardware and tools:

- One #2 Phillips screwdriver and one #2 pozidriv screwdriver. See Tool Requirements.

- The left and right rails.

- For all rack types, the contents of the COMMON BAG.

PS4000 Rack Mount Instructions 5

2. Orient the mounting rail in its proper position. Each rail is stamped with either “LH Front” or “RH

Front.” When the rails are properly positioned, the brackets are closer to the rear of the rack and

pointing up. See Figure 2.

Figure 2 Adjusting the Length of a Mounting Rail

3. Attach the front of the rail to the inside of the front pole (Figure 3, callout ) using one Phillips head

screw, one spring washer, and one plain washer from the COMMON bag.

4. Pull the rear flange until it meets the inside surface of the rear rack pole. See Figure 2.

Make sure the locator pins go through the rack holes at the same height (in the same relative holes on

the front and rear poles), according to the pole markings, if present. Use a level to make sure the rails

are level.

5. Attach the rear of the rail to the rear pole (Figure 3, callout ) using one Phillips head screw, one

spring washer, and one plain washer from the COMMON bag.

Figure 3 Attaching a Mounting Rail to the Front and Rear Poles

6PS4000 Rack Mount Instructions

Andere Handbücher für EqualLogic PS4000

Inhaltsverzeichnis

Andere Dell Lagerung Handbücher

Dell

Dell PowerVault DR4100 Handbuch

Dell

Dell SC400 Bedienungsanleitung

Dell

Dell PowerVault DL4000 Bedienungsanleitung

Dell

Dell PowerVault NX3500 Bedienungsanleitung

Dell

Dell PowerVault MD3200 Series Kurzanleitung

Dell

Dell PowerVault 132T LTO Bedienungsanleitung

Dell

Dell PowerVault DR4100 Bedienungsanleitung

Dell

Dell PowerVault 95P5378 Bedienungsanleitung

Dell

Dell PowerVault MD3860i Series Kurzanleitung

Dell

Dell PowerVault 124T Bedienungsanleitung

Dell

Dell PowerVault NX300 Bedienungsanleitung

Dell

Dell PowerVault Storage Area Network Bedienungsanleitung

Dell

Dell PowerVault 110T SDLT320 Bedienungsanleitung

Dell

Dell PowerVault ML6000 Betriebsanleitung

Dell

Dell PowerVault 2385P Bedienungsanleitung

Dell

Dell PowerVault MD3400 Kurzanleitung

Dell

Dell PS6500 Montageanleitung

Dell

Dell PowerVault MD3060e Series Bedienungsanleitung

Dell

Dell PowerVault NX400 Bedienungsanleitung

Dell

Dell EqualLogic FS7610 Montageanleitung

Dell

Dell PowerVault 735N Allgemeine Anweisungen

Dell

Dell PowerVault NX300 Bedienungsanleitung

Dell

Dell PowerVault ML6000 Bedienungsanleitung

Dell

Dell PowerVault MD3200 Series Kurzanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung