Dell PowerVault 775N Technisches Handbuch

www.dell.com | support.dell.com

Dell™ PowerVault™ 775N Systems

Information Update

Mise à jour des informations

Aktuelle Informationen

Actualización de la información

www.dell.com | support.dell.com

Dell™ PowerVault™ 775N Systems

Information Update

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarksusedinthistext:Dell,theDELLlogo,andPowerVaultaretrademarksofDellComputerCorporation;Microsoft

and Windows are registered trademarks of Microsoft Corporation; Xeon is a trademark and Intel is a registered trademark

of Intel Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

July 2003 P/N H2083 Rev. A00

Information Update 1-1

This document provides updated information about the following topics for your system:

• Installing the SCSI cable strain-relief bracket

• System features

• Microprocessor features

• System memory features

• System board connectors for memory modules

• Broadcom NetXtreme Gigabit Ethernet Server Adapter

• Console redirection special key functions

Installing the SCSI Cable Strain-Relief Bracket

1Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2Ensure that the system is pushed back as far as possible in the rack.

3Connect any SCSI cables to the system before connecting the I/O cables.

NOTE: To use the strain-relief bracket, only two SCSI cables can be connected to each I/O

slot at a time. The cables cannot be stacked, one above the other; they must be either side-

by-side or placed diagonally to each other.

4Install the strain-relief bracket to the back of the system.

aInsert the ends of the three long portions of the strain-relief bracket into the three

matching holes in the rail bracket (see Figure 1-1).

bSecure the captive thumbscrew to the back of the system (see Figure 1-1).

5Connect the I/O cables to the back of the system.

For information on routing system cables, see your Rack Installation Guide.

1-2 Information Update

www.dell.com | support.dell.com

Figure 1-1. Installing the Strain-Relief Bracket

System Features

Your system contains the following new system features:

• Up to two Intel®Xeon™ microprocessors with a front-side bus speed of 533 MHz, an

internal operating speed of at least 2.0 GHz, and 512 KB of internal level-2 cache.

NOTE: Your system does not support dual microprocessors with different front-side buses.

• PC-2100 registered 266 MHz DDR SDRAM memory modules.

NOTE: Your system must have BIOS version A13 or later.

matching rail

bracket holes (3)

strain-relief

bracket

captive

thumbscrew

Information Update 1-3

Microprocessor Features

The Intel Xeon microprocessors in your system provide NetBurst microarchitecture and

Hyper-Threading Technology to significantly increase microprocessor performance. Hyper-

Threading allows one physical microprocessor to appear as two logical processors to the

operating system and application programs. Hyper-Threading also allows each

microprocessor to simultaneously execute multiple tasks using shared hardware resources.

These new technology features in the microprocessor provide the following for

multithreaded tasks:

• Enhanced system performance

• Improved reaction and response time for the system

• Increased number of users that a system can support

• Increased number of transactions that can be executed simultaneously by the system

The CPU Information option in the System Setup program’s main screen displays

information about the different processors in the system (speed, cache size, and others.).

After the microprocessor information is displayed, you can enable or disable Hyper-

Threading by changing the setting of the Logical Processor option. (The default is

Enabled.)

System Memory Features

Your system features redundant memory, which provides the system with a failover memory

bank when an active memory bank has excessive single-bit errors. This failover occurs

without the need to halt or restart the system. You can enable this feature in the System

Setup program. For more information about the System Setup program, see your User's

Guide.

To enable the Redundant Memory option in the System Setup program, all memory slots in

the system must be populated, and all memory modules must be of the same type and size.

The redundant memory options vary according to the number of populated memory banks

and whether identical memory modules are installed in each bank:

•Disabled — One or more banks are not populated, or not all memory modules are of

the same type and size.

•Disabled and Spare Bank Enabled — All three memory banks are populated with

memory modules of the same size and type.

1-4 Information Update

www.dell.com | support.dell.com

System Board Connectors for Memory Modules

See Figure 1-2 for the location and the updated description of the memory module

connectors on the system board.

For more information on system board connectors, see your Installation and Troubleshooting

Guide.

Figure 1-2. System Board Connectors for Memory Modules

BANK1_A connector

BANK1_B connector

BANK2_A connector

BANK2_B connector

BANK3_A connector

BANK3_B connector

Information Update 1-5

Broadcom NetXtreme Gigabit Ethernet Server

Adapter

When a Broadcom NetXtreme Gigabit Ethernet Server Adapter is installed and Wakeup

On LAN (WOL) is enabled, your system’s connection speed is 10/100 Mbps. The

Broadcom NetXtreme Gigabit Server Adapter only supports 10/100-Mbps links when WOL

is enabled and the system is in Microsoft®Windows®2000 Server and Advanced Server

hibernation.

When the operating system loads and the correct drivers are installed, your supported

connection speed is 10/100/1000 Mbps. It is recommended that when WOL support is

required, the Broadcom NetXtreme Gigabit Server Adapter is connected to a 10/100/1000

link partner in autonegotiation mode.

WOL is supported on only one Ethernet port in the system, which does not include the

system management port. If you are using an integrated NIC for this purpose, you must use

the NIC 1 connector. WOL is not supported on Broadcom NetXtreme Gigabit 5703

Ethernet adapters.

You can find more information about Hyper-Threading Technology at developer.intel.com.

Console Redirection Special Key Functions

Table 1-1 lists additional ANSI escape sequences that represent a special key or function.

For additional information on console redirection and configuring special key functions, see

"Console Redirection" in your User’s Guide.

NOTE: ANSI escape-sequence key combinations listed in Table 1-1 are case-sensitive.

For example, to generate the character <Insert> you must press <Esc> and then

press <Shift><+>.

Table 1-1. Additional ANSI Escape Sequences

Key(s) Supported Sequence Terminal Emulation

<Home> <Esc><h> ANSI

<End> <Esc><k> ANSI

<Insert> <Esc><Shift><+> ANSI

<Delete> <Esc><-> ANSI

<Page Up> <Esc><Shift><?> ANSI

<Page Down> <Esc></> ANSI

<Shift><Tab> <Esc><[><Shift><z> ANSI

1-6 Information Update

www.dell.com | support.dell.com

Andere Handbücher für PowerVault 775N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Dell Lagerung Handbücher

Dell

Dell PowerVault MD3400 Kurzanleitung

Dell

Dell PowerVault 35F Bedienungsanleitung

Dell

Dell PowerVault NX1950 Kurzanleitung

Dell

Dell SC180 Bedienungsanleitung

Dell

Dell Inspiron 3700 Bedienungsanleitung

Dell

Dell PowerVault 110T DLT VS80 Bedienungsanleitung

Dell

Dell EqualLogic PS Series Benutzerhandbuch

Dell

Dell PowerVault 200S Bedienungsanleitung

Dell

Dell PowerEdge Bedienungsanleitung

Dell

Dell PowerVault NX1950 Gebrauchsanweisung

Dell

Dell PS4100 Montageanleitung

Dell

Dell PowerVault TL4000 Bedienungsanleitung

Dell

Dell PowerVault 120T DDS4 Bedienungsanleitung

Dell

Dell PowerVault MD3600i Series Bedienungsanleitung

Dell

Dell PowerEdge R520 Bedienungsanleitung

Dell

Dell PowerVault MD3660f Series Kurzanleitung

Dell

Dell PowerVault 110T LTO Bedienungsanleitung

Dell

Dell PowerVault 132T Installations- und Betriebshandbuch

Dell

Dell PowerVault 120T DLT1 Technisches Handbuch

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

Dell

Dell EqualLogic PS5000 Betriebsanleitung

Dell

Dell PowerVault 114T 2U Bedienungsanleitung

Dell

Dell PowerVault NX3500 Bedienungsanleitung

Dell

Dell EqualLogic FS7600 Montageanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung