Dell MXG610s Bedienungsanleitung

MXG610s Fibre Channel Switch

Module Setup Guide

Supporting fabric OS 8.1.0_Inx

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of

your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury,

or death.

are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective

owners.

2018 -07

Rev. A00

Contents

1 About this guide.............................................................................. 4

2 MXG610s Setup Guide................................................................... 5

Blade server preparation......................................................................... 5

Switch module installation.......................................................................5

Serial connection...................................................................................... 8

Static IP addresses...................................................................................9

Optical transceivers and cabling installation........................................ 12

Port-side LEDs........................................................................................ 13

Additional country-specic IEEE notices............................................. 14

3 Dell EMC support.......................................................................... 17

Contents 3

About this guide

This guide provides site preparation recommendations, step-by-step procedures for rack

mounting and desk mounting, inserting modules, and connecting to a power source.

CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist

straps when handling this equipment.

WARNING: Only trained and qualied personnel can install this equipment. Read

this guide before you install and power up this equipment. This equipment contains

two power cords. Disconnect both power cords before servicing.

WARNING: This equipment contains optical transceivers, which comply with the

limits of Class 1 laser radiation.

Figure 1. Class 1 laser product tag

WARNING: When no cable is connected, visible and invisible laser radiation may be

emitted from the aperture of the optical transceiver ports. Avoid exposure to laser

radiation and do not stare into open apertures.

4 About this guide

MXG610s Setup Guide

Topics:

• Blade server preparation

• Switch module installation

• Serial connection

• Static IP addresses

• Optical transceivers and cabling installation

• Port-side LEDs

• Additional country-specic IEEE notices

Blade server preparation

Before you insert the switch module in the blade server chassis, meet the following

conditions:

• The blade server is powered up.

• The blade server chassis meets all its specic power requirements.

• The I/O module bay C1 or C2 is empty and ready to receive the switch module.

• If you are replacing an existing switch module, to maintain the proper cooling level in the

chassis, insert the replacement switch module within one minute.

Switch module installation

Insert the switch modules in the blade server chassis slots and check that the modules are

functioning properly.

MXG610s Setup Guide 5

NOTE: The switch module works in switch module slots C1 and C2 in the blade

server chassis. Do not insert the switch module in any other slot because this

action may damage the chassis or switch module connector pins.

1 Remove the orange plastic protective cover for the backplane connector.

Figure 2. Dell EMC PowerEdge MX7000 chassis back view with switch module slots

marked

1PowerEdge MX7000 chassis back

view

2 Switch module slot C2

3 Switch module slot C1

2 Orient the switch module port side facing you.

The module latch is on the right side.

6MXG610s Setup Guide

Figure 3. Switch module orientation

1Backplane connectors 2 Switch module top view

3 Switch module latch in open

position

3 Open the release lever, and slide the switch module into the blade server chassis slot

completely.

MXG610s Setup Guide 7

You hear a click when the switch module is locked in the blade server chassis I/O

module bay. If the power is on in the blade server chassis, locking the switch module in

the module bay provides power and turn-ons the switch module and the LEDs.

The switch module then runs POSTs. These tests can take up to two minutes to

complete. After the power/status LED light is steady green for at least two minutes,

the module is ready to use.

4 Start from port 0, then port 17, and then the rest of the ports when cabling the SFP+

ports.

If you use QSFP ports instead of SFP+ ports, transfer the port license from port 0 and

17 to the desired QSFP ports. The QSFP ports must be unused and no additional port

licenses are available. Ports 0 and 17 are prelicensed at the factory.

You are now ready to insert more SFP+/QSFP optical transceivers, if needed. Be sure to

use only Brocade-branded SFP+/QSFP optical transceivers. The FC switch module does

not recognize unapproved products.

Serial connection

To log in to the switch module through the serial connection on the front panel, port-side

view, perform the following steps:

1 Connect the console cable with the micro-USB connector to the console port on the

switch module and to a USB port on the workstation.

2 Disable any serial communication programs running on the workstation such as

synchronization programs.

3 Open a terminal emulator application such as PuTTY, XShell, or SecureCRT on a

Windows PC, or TERM, TIP, or C-Kermit in a LINUX environment. Congure the

application as follows:

• In a WIndows environment, use the following values:

– Bits per second—9600

– Databits—8

– Parity—None

– Stop bits—1

– Flow control—None; must be disabled on the host side

NOTE: Flow control is not supported on the serial connection when attached

to a remote terminal. You must disable ow control on the customer-side

remote terminal server in addition to the host-side clients.

8 MXG610s Setup Guide

• In a UNIX environment using TIP, enter tip /dev/ttyb -9600. at the prompt.

• If you are already using ttyb, use ttya instead and enter tip /dev/ttya -9600

at the prompt.

4 Press enter when the terminal emulator application stops reporting information to

display the login prompt.

Switch Console Login:

5 Log in to the switch module as admin, using the default password: password.

You are prompted to change the default admin and user passwords at initial login. Write

down the new passwords, and keep this information in a secure location.

Fabric OS (swDir)

swDir login: admin

Password:

Please change your passwords now.

Use Control-C to exit or press 'Enter' key to proceed.

swDir:admin>

6 (Optional) Modify passwords.

To skip modifying the password, press Ctrl+C.

NOTE: Passwords are 8 to 40 characters long. They must begin with an

alphabetic character. They can include numeric characters, the period (.), and

the underscore (_) only. Passwords are case-sensitive, and do display when

you enter them on the command line.

Static IP addresses

Dell EMC recommends conguring the switch module through the blade server chassis

management GUI, namely, Dell EMC OpenManage Enterprise Modular. Use this

management GUI to congure the switch IP address and perform advanced conguration

tasks. By default, the IP address mode is set to DHCP. Use this GUI to assign a static IP

address. To congure the FC switch module, follow these steps:

1 Log in to the blade server chassis management GUI application.

Figure 4. OpenManage Enterprise modular

2 Select Devices > I/O modules.

MXG610s Setup Guide 9

The I/O modules display.

NOTE: You may also access the WebTools conguration UI to manage the

switch module by typing the switch module IP address into any supported web

browser.

Figure 5. I/O modules list

3 Select the I/O module name, IP address, or View Details on the right side of the

display.

The Overview tab is displayed. Select the Settings tab.

Figure 6. Settings tab

4 Click and expand the Network option. Select the required check boxes, and complete

the IPv4 or IPv6 settings, DNS server settings, and optionally the management VLAN

ID. Click Apply.

10 MXG610s Setup Guide

Andere Handbücher für MXG610s

Inhaltsverzeichnis

Andere Dell Schalten Handbücher

Dell

Dell Dell SC Series Bedienungsanleitung

Dell

Dell Broadcom NetXtreme Family of Adapters Bedienungsanleitung

Dell

Dell PowerConnect 2016 Bedienungsanleitung

Dell

Dell SMA 200 Bedienungsanleitung

Dell

Dell PowerEdge 180AS Montage- und Wartungsanleitung

Dell

Dell Wyse R Class Bedienungsanleitung

Dell

Dell Force10 S60 Series Bedienungsanleitung

Dell

Dell PowerConnect 3424 Anleitung zur Verwendung

Dell

Dell PowerConnect 3048 Bedienungsanleitung

Dell

Dell 8 Bedienungsanleitung

Dell

Dell S60 System Bedienungsanleitung

Dell

Dell PowerConnect M6348 Bedienungsanleitung

Dell

Dell Networking S55 Bedienungsanleitung

Dell

Dell N2000 Series Bedienungsanleitung

Dell

Dell POWERCONNECT 5524 Bedienungsanleitung

Dell

Dell PowerConnect M6348 Bedienungsanleitung

Dell

Dell PowerEdge M IO Aggregator Bedienungsanleitung

Dell

Dell Networking 7048 Bedienungsanleitung

Dell

Dell Force10 S50N Series Bedienungsanleitung

Dell

Dell Force10 S4810P Bedienungsanleitung

Dell

Dell PowerConnect B-RX Bedienungsanleitung

Dell

Dell Z9100-ON Bedienungsanleitung

Dell

Dell PowerConnect W-IAP175P Bedienungsanleitung

Dell

Dell S4810-ON Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung