Dell POWERCONNECT 2800 Series Bedienungsanleitung

CALLN HOSTED CALL RECORDING

PORT MIRRORING SETUP

DELL POWERCONNECT 2800

SERIES

Created by Chris Lane

15 November 2017

Version 1.0.1

Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 2 of 5

Table of Contents

1. Introduction .........................................................................................................................3

2. Connectivity..........................................................................................................................4

3. Configuration of Port Mirroring ................................................................................5

Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 3 of 5

1. Introduction

This document describes how to configure your DELL PowerConnect 2800 series network switch to work

with CallN. All switches in the DELL PowerConnect 2800 series have an identical interface and for the

purposes of this guide, are interchangeable.

Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 4 of 5

2. Connectivity

To successfully record calls, the DELL switch needs to be placed into the network where it will be able to

record all VOIP traffic. This could mean the VOIP traffic is connected directly to the DELL switch and

phones are connected to the switch as well, or the VOIP traffic is connected to the DELL switch which is

then connected to other switches which phones connect.

The CallN recording computer requires two network connections. One network connection is connected

to the destination port of the port mirror configuration. Typically, this will be the last port on your switch,

but can be a nominated port at the time of configuring port mirroring.

The second port is a standard connection to the LAN which allows CallN to upload voice recordings to the

CallN portal.

Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 5 of 5

3. Configuration of Port Mirroring

The DELL PowerConnect 2800 Series of network switch has an Unmanaged Mode, a Managed Mode and

a Secure Mode. By default, a new switch will be in Unmanaged Mode. In this mode there is no web

interface to configure the switch. The switch must be in Management Mode to configure. To change the

switch to Managed Mode, press the Mode button for up to 7 seconds.

Connect a computer to switch and put the computer into the same subnet as the switch. By default, the

switch IP Address is 192.168.2.1 with a subnet mask of 255.255.255.0. Enter in the username and

password when prompted. The default username is Admin and has no password.

Once the interface is open, expand the Switch menu on the left, and then expand the Ports menu. From

the list select Port Mirroring.

Select Add to open the “Add Source Port” page.

Set the Destination Port from the drop down list. This is the port the Recording Computer will listen to

traffic on and record calls. Ports are listed with a preceding ‘g’. For example, port 1 will show as g1.

Set Source Port from the drop down list. This is the port on the switch that leads back to a PBX or

internet connection but it needs to be a port that will see all VOIP traffic.

Set Type to “Tx and Rx” from the drop down list. By setting it to “Tx and Rx” the switch will copy all

received and sent traffic to the destination port. If it is not set to this, only one party of call will be

recorded.

Press Apply Changes.

NOTE:

▪Source ports and destination port cannot be a LAG member.

▪A source port cannot be a destination port and a destination port cannot be a source port.

▪A destination port is not a VLAN member.

▪GVRP is not enabled on the destination port.

▪Only one destination port can be defined.

Port mirroring is now configured. New calls will now be recorded and uploaded to your CallN portal.

Inhaltsverzeichnis

Andere Dell Schalten Handbücher

Dell

Dell C7004/C150 Montageanleitung

Dell

Dell EMC PowerSwitch S6100-ON Bedienungsanleitung

Dell

Dell PowerConnect 5212 Bedienerhandbuch

Dell

Dell N4000 Series Bedienungsanleitung

Dell

Dell PowerEdge M IO Aggregator Betriebsanleitung

Dell

Dell Dell SC Series Bedienungsanleitung

Dell

Dell PowerConnect J-EX4200-24T Kurzanleitung

Dell

Dell X1000 Series Bedienungsanleitung

Dell

Dell S6000-ON Bedienungsanleitung

Dell

Dell PowerEdge 2321DS Bedienungsanleitung

Dell

Dell N2128PX-ON Bedienungsanleitung

Dell

Dell PowerConnect B-RX Bedienungsanleitung

Dell

Dell N1500 Series Gebrauchs- und Pflegehandbuch

Dell

Dell PowerConnect M8428-k Anleitung zur Verwendung

Dell

Dell PowerVault 50F Bedienungsanleitung

Dell

Dell PowerConnect 3524 Bedienungsanleitung

Dell

Dell Networking S5000 Bedienungsanleitung

Dell

Dell Z9100-ON Bedienungsanleitung

Dell

Dell PowerConnect 2816 Bedienungsanleitung

Dell

Dell PowerConnect 6224 Bedienungsanleitung

Dell

Dell SMA 200 Bedienungsanleitung

Dell

Dell Brocade VDX 6740 Bedienungsanleitung

Dell

Dell PowerEdge M420 Bedienungsanleitung

Dell

Dell PowerConnect 2808 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung