Dell X1000 Series Bedienungsanleitung
Dell™ Networking™ X1000
and X4000 Series Switches
Getting Started Guide
使用入门指南
入門指南
Panduan Pengaktifan
はじめに
시작 안내서
Dell™ Networking™ X1000
and X4000 Series Switches
Getting Started Guide
Regulatory Models: X1008, X1008P, X1018,
X1026, X4012, X1018P, X1026P, X1052,
X1052P
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of
your device.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of
data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international
copyright and intellectual property laws.
Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions.
All other marks and names mentioned herein may be trademarks of their respective companies.
P/N RF9YW Rev. A00
Getting Started Guide 3
Welcome
This document provides basic information to install and start running the
following Dell Networking X-series switches: X1008/X1008P, X1018/X1018P,
X1026/X1026P, X1052/X1052P and X4012.
The switch is delivered from the factory in Unmanaged Mode to avoid
unauthorized access to the switch. To use the switch in Managed Mode,
press the Mode button for at least seven seconds. The MGMT LED will
illuminate when in Managed Mode. To switch back to Unmanaged Mode,
repeat the process.
These Dell networking devices are ideal for the small to medium business
that requires high performance network connectivity along with advanced
web management features. The management features are designed to
minimize administrative management effort, while enhancing and improving
network traffic control.
For the latest documentation and software updates, go to dell.com/support.
Safety Environmental and Regulatory Information (SERI) is included in the
printed documentation.
Package Contents
While unpacking the device, make sure that the following items are included:
• The ordered network switch
• AC power cable (and power brick only for the X1008 and X1008P)
• Console micro-USB serial cable
• Self-adhesive rubber pads (for desk or shelf installation on select systems)
• Installation kit
• Safety Environmental and Regulatory Information document
•Placemat
• This Getting Started Guide
4Getting Started Guide
X1000 and X4000 Series Switches Summary
Mounting the Device
Rack Installation
WARNING: Read the safety information in SERI as well as the safety information
for other switches that connect to or support the switch.
WARNING: Disconnect all cables from the switch before mounting the switch in
a rack or cabinet.
CAUTION: When mounting multiple switches into a rack, mount the switches
from the bottom up.
Install the switch in a rack with brackets as follows (52 port switches have
a ready rail kit):
1
Place the supplied rack-mounting bracket on one side of the switch
making sure the mounting holes on the switch line up to the mounting
holes on the rack mounting bracket.
Table 1-1. X1000 and X4000 Series Switches Summary
Marketing Model
Name
Power Supply Unit Regulatory Model
Number
Regulatory Type
Number
X1008 External, 24W E08W E08W001
X1008P External, 150W E09W E09W001
X1018 Internal, 40W E10W E10W001
X1026 Internal, 40W E10W E10W002
X4012 Internal, 100W E10W E10W003
X1018P Internal, 280W E11W E11W001
X1026P Internal, 450W E11W E11W002
X1052 Internal, 100W E12W E12W001
X1052P Internal, 525W E12W E12W002
Getting Started Guide 5
Figure 1-1. Bracket Installation for Rack Mounting
2
Insert the supplied screws into the rack mounting holes and tighten with
a screwdriver.
3
Repeat the process for the rack-mounting bracket on the other side of
the switch.
4
Insert the switch into the rack, making sure the rack-mounting holes on
the switch line up to the mounting holes on the rack.
5
Secure the switch to the rack with the rack screws (not provided).
Fasten the lower pair of screws before the upper pair of screws.
Make sure that the ventilation holes are not obstructed.
Flat Surface Installation
The switch can be installed on a flat surface if it is not installed on a rack.
The surface must be able to support the weight of the switch and the
switch cables.
1
Attach the self-adhesive rubber pads (provided with the switch) on each
marked location on the bottom of the chassis.
2
Set the switch on a flat surface, while leaving two inches (5.08 cm) on each
side and five inches (12.7 cm) at the back.
3
Make sure that the switch has proper ventilation.
6Getting Started Guide
Wall Installation
To mount the switch on a wall:
1
Make sure that the mounting location meets the following requirements:
• The surface of the wall must be capable of supporting the switch.
• Allow at least two inches (5.1 cm) space on the sides for proper
ventilation and five inches (12.7 cm) at the back for power
cable clearance.
• The location must be ventilated to prevent heat buildup.
2
Place the supplied wall-mounting bracket on one side of the switch,
verifying that the mounting holes on the switch line up to the mounting
holes on the wall-mounting bracket.
Figure 1-2. Bracket Installation for Wall Mounting
3
Insert the supplied screws into the wall-mounting bracket holes and
tighten with a screwdriver.
4
Repeat the process for the wall-mounting bracket on the other side of
the switch.
5
Place the switch on the wall in the location where the switch is being installed.
6
On the wall mark the locations where the screws to hold the switch must
be prepared.
Getting Started Guide 7
7
On the marked locations, drill the holes and place all plugs (not provided)
in the holes.
8
Secure the switch to the wall with screws (not provided). Make sure that
the ventilation holes are not obstructed.
Starting and Configuring the Switch
Management Modes
The Dell Networking X1008/18/26 and equivalent PoE versions have a Mode
push button that toggles between Managed and Unmanaged Modes. The
MGMT LED is on when the switch is in Managed Mode and is off when in
Unmanaged Mode. To configure the switch while in Managed Mode, see the
following sections.
NOTE: Release notes and user documentation can be downloaded from
dell.com/support.
Connecting the Switch to the Network
CAUTION: Do not plug a phone jack connector into an RJ-45 port. This will
damage the Ethernet switch. Use only twisted-pair cables with RJ-45 connectors
that conform to FCC standards.
To connect the switch to the network:
• Attach one end of a twisted-pair cable to the switch's RJ-45 connector and
the other end of a twisted-pair cable to another switch or server.
As each connection is made, the link LED corresponding to each port on the
switch is illuminated (green or amber) indicating that the connection is valid.
8Getting Started Guide
Initial Configuration Through the Web
The administrator can perform switch configuration using the web
management GUI.
To configure the switch, perform the following:
1
Verify that the switch is in Managed Mode.
2
Connect the switch to a PC using Ethernet, and set a static IP address of
192.168.2.x
(where x is between 2 and 254) and subnet mask of
255.255.255.0
on the PC. Note that the switch acts as a DHCP client and
can receive its IP address from a DHCP server. If using DHCP for IP
assignment, look up the assigned IP address and use it for the next step.
3
Connect to the switch using the default switch IP address
192.168.2.1
in
your web browser. The login username is
admin
with password
admin
.
4
After logging into the switch using the previous step, a getting started
wizard is available to guide the user through the initial switch
configuration. Applied changes are automatically saved to the startup
configuration.
CLI Access
To access the switch using the Command Line Interface (CLI), it must be in
Managed Mode. The Command Line Interface can only be reached by using
telnet or a console connection. See the user guide for limited CLI options.
NOTE: The default switch setting is Unmanaged Mode. To set the switch to
Managed Mode, press the Mode button for at least seven seconds.
Connecting the Switch to a Terminal Server/PC
NOTE: The console port enables connecting to a terminal or desktop system
running terminal emulation software for monitoring or debugging the device using
the micro-USB port. (You can find the USB drivers at dell.com/support.)
To use the console port, the following is required (e.g., PuTTY, TeraTerm, etc.)
• VT100 compatible terminal or a desktop or portable system with a USB
port and running VT100 terminal emulation software.
Andere Handbücher für X1000 Series
3
Dieses Handbuch passt für folgende Modelle
10
Inhaltsverzeichnis
Sprachen:
Andere Dell Schalten Handbücher
Dell
Dell PowerConnect B-RX16 Bedienungsanleitung
Dell
Dell PowerConnect 6224 Bedienungsanleitung
Dell
Dell 5324 - PowerConnect Switch Bedienungsanleitung
Dell
Dell PowerConnect M8428-k Bedienungsanleitung
Dell
Dell POWERCONNECT J SERIES Bedienungsanleitung
Dell
Dell Force10 S50N Series Bedienungsanleitung
Dell
Dell PowerConnect B-FCXs Bedienungsanleitung
Dell
Dell PowerConnect W-IAP175P Bedienungsanleitung
Dell
Dell PowerConnect 3424 Bedienungsanleitung
Dell
Dell PowerConnect J-EX8208 Montageanleitung
Dell
Dell PowerConnect 8132 Bedienungsanleitung
Dell
Dell Networking N4032 Bedienungsanleitung
Dell
Dell PowerConnect B-RX Bedienungsanleitung
Dell
Dell PowerEdge 1855 Bedienungsanleitung
Dell
Dell Brocade VDX 6740 Bedienungsanleitung
Dell
Dell PC2216 Bedienungsanleitung
Dell
Dell PowerConnect 2216 Bedienungsanleitung
Dell
Dell EMC PowerSwitch S5148F-ON Bedienungsanleitung
Dell
Dell S3100 Series Bedienungsanleitung
Dell
Dell EMC N2200-ON Series Bedienungsanleitung
