Dellonda DH127 Bedienungsanleitung

90cm Chimney Style Cooker Hood+Carbon Filters-S/Steel

Model No. DH127

Thank you for purchasing a Dellonda product. Manufactured to a high standard, this product will,

if used according to these instructions, and properly maintained, give you years of trouble free performance.

DG127 Issue:2 08/06/22

www.dellonda.co.uk

Important Information

Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care

for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these

instructions safe for future use.

Refer to

instruction

manual

Warning:

Hot

Surface

Specication

Airow: 340m³/h

Cable Length: 1.5m

Colour: Stainless Steel - 430SS

Control: 3 Speed Push Button

Design: Chimney

Energy Efciency Class: B

Headroom: 90cm

Power: 65W

Product dimensions: 900 x 475 x 580/960mm

Supply: 220-240V

Type: Wall Mounted

Safety Instructions

• ELECTRICAL SAFETY

• WARNING! It is the user’s responsibility to check the following:

• Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical

connections for wear and damage. Dellonda recommend that an RCD (Residual Current Device) is used with all electrical products. You may

obtain an RCD by contacting your local domestic stockist. If the product is used in the course of business duties, it must be maintained in a

safe condition and routinely PAT (Portable Appliance Test) tested.

• Electrical safety information: It is important that the following information is read and understood.

• Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

• Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

• Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct fuse - see

fuse rating in these instructions.

• DO NOT pull or carry the appliance by the power cable.

• DO NOT pull the plug from the socket by the cable.

• DO NOT use worn or damaged cables, plugs or connectors.

• Ensure that any faulty item is repaired or replaced immediately by a qualied electrician.

• This product is tted with a BS1363/A 13 Amp 3 pin plug. If the cable or plug is damaged

during use, switch off the electricity supply and remove from use. Ensure that repairs are

carried out by a qualied electrician.

• Replace a damaged plug with a BS1363/A 13 amp 3 pin plug. If in doubt contact a qualied electrician.

A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

B) Connect the BROWN live wire to the live terminal ‘L’.

C) Connect the BLUE neutral wire to the neutral terminal ‘N’.

• Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.

• Dellonda recommend that installation and repairs are carried out by a qualied electrician.

• GENERAL SAFETY

• This manual explains the proper installation and use of your cooker hood, please read it carefully before using even if you are familiar with the

product. The manual should be kept in a safe place for future reference.

• DO NOT try to use the cooker hood without the grease lters or if the lters are excessively greasy!

• DO NOT install above a cooker with a high level grill.

• DO NOT leave frying pans unattended during use because overheated fats or oils might catch re.

• Never leave naked ames under the cooker hood.

• If the cooker hood is damaged, do not attempt to use.

• DO NOT ambé under the cooker hood.

• CAUTION: Accessible parts may become hot when used with cooking appliances.

• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood, when the

cooker hood is located above a gas appliance, shall be at least 65 cm.

• The air must not be discharged into a ue that is used for exhausting fumes from appliances burning gas or other fuels.

• ALWAYS:

• Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.

• The cooker hood must be installed in accordance with the installation instructions and all measurements followed.

• All installation work must be carried out by a competent person or qualied electrician.

• Please dispose of the packing material carefully. Children are vulnerable to it.

• Pay attention to the sharp edges inside the cooker hood especially during installation and cleaning.

• Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efciency of the cooker hood.

Replacement fuse rating:

13A

• WARNING: Failure to install the screws or xing device in accordance with these instructions may result in electrical hazards.

• WARNING: Before obtaining access to terminals, all supply circuits must be disconnected.

• Always put lids on pots and pans when cooking on a gas cooker.

• When in extraction mode, air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being

observed.

• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.

• The cooker hood removes odours from room but not steam.

• Cooker hood is for domestic use only.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a hazard.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• WARNING: Before obtaining access to terminals, all supply circuits must be disconnected.

• CAUTION: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children

younger than 8 years old should stay away unless they are under permanent supervision.

• There is a re risk if cleaning is not carried out in accordance with the instructions

• Regulations concerning the discharge of air have to be fullled.

• Clean your appliance periodically by following the method given in the chapter MAINTENANCE.

• For safety reason, please use only the same size of xing or mounting screw which are recommended in this instruction manual.

• Regarding the details about the method and frequency of cleaning, please refer to maintenance and cleaning section in the instruction manual.

• Cleaning and user maintenance shall not be made by children without supervision.

• When the cooker hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the

room must not exceed 4 Pa (4 x 10-5 bar).

• WARNING: Danger of re: do not store items on the cooking surfaces.

• A steam cleaner is not to be used.

• NEVER try to extinguish a re with water, but switch off the appliance and then cover ame e.g. with a lid or a re blanket.

• INSTALLATION (VENT OUTSIDE)

• V-FLAP MOUNTING

• If the cooker hood does not have an assembled V-flap 1, mount the half-parts to its body. The images only show an example of how to mount the

V-flap, the outlet may be various according to different models and configuration.

• To mount the V-flap 1:

• Mount two halves 2 into the body 6

• pin 3 should be on the top;

• the axle 4 should be inserted in the holes 5 on body;

• repeat all the operations for the 2nd half.

INSTALLATION

• If you have an outlet to the outside, your cooker hood can be connected as per g.2 by means of an extraction duct (enamel, aluminium, exible

pipe or non-ammable material with an interior diameter of 150mm).

• Before installation, turn the unit off and unplug it from the mains supply.

• The cooker hood should be placed at a distance of 65~75cm above the cooking surface for best performance, g.3.

fig.1

fig.2fig.3

• Install the hook in a suitable place once the installation height is xed, and keep it in line. The xed position of the inside chimney bracket is the

place of the chimney.

• Drill 5 Ø8mm holes on a suitable place to accommodate the hook and inside chimney bracket once the installation height is xed, keep it in line.

The xed position of the inside chimney bracket is the place of chimney. See g.4.

• Screw and tighten the hook onto the wall with the 3pcs screws (4mm x 40 mm) and wall plugs provided. Then use 2 pcs ST4*40mm screws to x

the inside chimney bracket. See g.4.

• Install the expansion pipe to the outlet and xed by cable tie. See g.5.

• Fix the outside chimney bracket on the outside chimney, and be sure that the inside chimney can be adjusted for height. See g.6.

• Hang the appliance onto the hook and x the appliance by the 2pcs safety screws (4mm x 30mm). See g.7

• Adjust the height of the inside chimney to the position of the inside chimney bracket and x with a screw. Note: The two safety vents are

positioned on the back housing. See g.8.

• Before usage, read all the instructions and make sure that the power rating of the cooker hood matches the power rating of the supply.

EXHAUST DUCT INSTALLATION

• The following rules must be strictly followed to obtain optimal air extraction:

• Keep expansion pipe short and straight.

• DO NOT reduce the size or restrict expansion pipe.

• When using expansion pipe always install the pipe pulled taut to minimize pressure loss.

• Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood.

fig.4

fig.6

fig.7

fig.8

fig.5

fig.8

• Any installation work must be carried out by a qualied electrician or competent person.

• DO NOT connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance, such as warmer

tube, gas tube, hot wind tube.

• The angle of the bend of the expansion pipe should not be less than 120º; you must direct the pipe horizontally, or, alternatively, the pipe should

go up from the initial point and should be led to an outer wall.

• After the installation, make sure that the cooker hood is level to avoid grease collection at on end, g.9.

• Ensure the expansion pipe selected for installation complies with relevant standards and is re retardant.

• WARNING For safety reasons, please use only the same size of xing or mounting screws which are recommended in this instruction manual.

• Failure to install the screws or xing device in accordance with these instructions may result in electrical hazards.

OPERATION

• 1) Push stop button, and the motor will stop.

• 2) Push the low button, and the motor runs at low speed.

• 3) Push the middle button, and the motor runs at mid speed.

• 4) Push the high button, and the motor runs at high speed.

• 5) Push the light button and the two lights will come on. Push it again and the light will turn off.

TROUBLESHOOTING

Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service centre if in any doubt

before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

MAINTENANCE AND CLEANING

• WARNING• Before maintenance or cleaning is carried out, the cooker hood should be disconnected from the main power supply. Ensure that the

cooker hood is switched off at the wall socket and the plug removed.

• External surfaces are susceptible to scratches and abrasions, so please follow the cleaning instructions to ensure the best possible result is

achieved without damage.

Fault Cause Solution

Light on but motor does not work Fan switch turned o󰀨 Select a fan switch position

Fan switch failed Contact service centre

Motor failed Contact service centre

Light does not work, motor does not work House fuses blown Reset/replace fuses

Mains cable loose or disconnected Ret mains power cable to power outlet.

Switch power on.

Oil leakage One way valve and the outlet are not

tightly sealed

Remove one way valve and seal with

sealant

Leakage from the connection of chimney

and cover

Take chimney down and seal

Lights not working Broken or faulty bulbs Replace bulbs as per instructions in this

manual

Insu󰀩cient suction Distance between the cooker hood and

the gas hob is too great

Ret the cooker hood to the correct

distance

Cooker hood inclines Fixing screws are not tight enough Tighten the hanging screw and make

horizontal

fig.9

Stop Low Middle High Light

• GENERAL

• Cleaning and maintenance should be carried out with the appliance cold especially cleaning. Avoid leaving alkaline or acid substances (lemon

juice, vinegar etc.) on the surfaces.

• STAINLESS STEEL

• The stainless steel must be cleaned regularly (e.g. weekly) to ensure long life expectancy. Dry with a clean soft cloth. A specialized stainless steel

cleaning uid may be used.

• NOTE: Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly criss-cross scratching patterns from

appearing.

• CONTROL PANEL SURFACE

• The control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to

remove any excess moisture left after cleaning.

• IMPORTANT

• Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or

products containing abrasives, as this will affect the appliance appearance and potentially remove any

printing of artwork on the control panel and will void manufactures warranty.

• GREASE MESH FILTERS

• The mesh lters can be cleaned by hand. Soak them for about 3 minutes in water with a grease-

loosening detergent then brush it gently with a soft brush. Do not apply too much pressure, to avoid

damage . (Leave to dry naturally out of direct sun light).

• Filters should be washed separately to crockery and kitchen utensils. it is advisable not to use rinse aid.

• INSTALLING GREASE MESH FILTERS g.10.

• To install lters:

• - Angle the lter into slots at the back of the hood.

• - Push the button on handle of the lter.

• - Release the handle once the lter ts into a resting position.

• - Repeat to install all lters.

• CARBON FILTERS g’s 11 & 12.

• Activated carbon lter can be used to trap odours. Normally the activated carbon lter should be

changed at three or six months according to your cooking habits. The installation procedure of activated

carbon lter is as below.

• 1. WARNING Before installing or replacing the carbon lters, remove from mains supply.

• 2. Press the lter lock and remove the mesh lter.

• 3. Turn the carbon lter on both side of the motor anti-clockwise. Replace the carbon lters with the new carbon lters.

• 4. Place the mesh lter.

• 5. Connect the power supply to the wall socket.

•

CONTROL PANEL

• NOTE: Make sure the lter is securely locked.

• Otherwise, it could loosen and be dangerous.

• When the activated carbon lter is tted, the suction power will be lowered.

• BULB REPLACEMENT

• The bulb must be replaced by the manufacturer, its service agent or similarly qualied persons.

• WARNING! Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it is

completely cool down before any direct contact to hands.

• When handling globes hold with a cloth or gloves to ensure perspiration does not come in contact with the globe as this can reduce the life of the

globe.

• Remove the grease lter.

• Locate the junction box, unscrew the screws on the junction box cover, then take off the junction box cover. If there is wire retaining plate this

needs to be dismantled rst. See g.14.The junction box has versions a and b, depending on different models.

• Locate the terminal of the light connecting wire disconnect. See g.15.

• Method 1: Use a tool or ngers to press the clip of both sides of LED light, until the light is pressed out, see g.16.Then slightly pull the light

connecting wire out.

• Method 2: Use a straight screwdriver to prize up the LED light bottom edge, see g.16, then slightly pull out the light connecting wire.

• Retting is the reverse procedure.

• ILCOS D code for this lamp is: DBS-1.5/65-H-201/39.5

• LED modules –rectangle lamp

• Max wattage: 1×1.5 W

• Voltage range: AC 220-240V

• dimensions see g.13.

fig.10

fig.11

fig.13

fig.12

fig.14

Environment Protection and Waste Protection and Electrical Equipment Regulations (WEEE)

Recycle unwanted packaging materials. When this product is no longer required, or has reached the end of it’s useful life, please dispose of it in

an environmentally friendly way. Drain any fluids (if applicable) into approved containers, in accordance with local waste regulations. Under the

Waste Batteries and Accumulators Regulations 2009, Dellonda would like to inform the user that this product contains one or more batteries. It

is our policy to continually improve products and we reserve the right to alter data, specifications and parts without prior notice. No liability is

accepted for incorrect use of this product. Guarantee is 12 months from purchase date, proof of which is required for any claim.

Dellonda Limited

Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757575 [email protected] www.dellonda.co.uk

fig.15

Inhaltsverzeichnis

Andere dellonda Dunstabzugshaube Handbücher

dellonda

dellonda DH129 Bedienungsanleitung

dellonda

dellonda DH130 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

dellonda DH127 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken