Delphi YDT262 Betriebsanleitung

HL018, Issue 2

YDT262

Dynamic Timing Control Box

(GB) Operating and Servicing Manual

(F) Manuel d’Utilisation et d’Entretien

(D) Bedienungs- und Wartungshandbuch

(E) Manual de Funcionamiento y Servicio

(I) Manuale di Utilizzo e Manutenzione

(P) Manual de Funcionamento e Manutencao

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

YDT262 Operating and Servicing Manual DELPHI DIESEL AFTERMARKET

2 HL018, Issue 2

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

DELPHI DIESEL AFTERMARKET YDT262 Operating and Servicing Manual

HL018, Issue 2 3

CONTENTS / TABLE DES MATIERES /

INHALTSVERZEICHNIS / INDICE

ENGLISH _______________________________________________________________________________5

FOREWORD _____________________________________________________________________________5

1. INTRODUCTION ______________________________________________________________________6

2. DEFINITION OF TERMS AND ABBREVIATIONS _______________________________________________6

3. PRINCIPLE OF OPERATION______________________________________________________________6

4. OPERATION_________________________________________________________________________7

4.1 Layout ___________________________________________________________________________7

4.2 Installation ________________________________________________________________________7

4.3 Software Operating Sequence _________________________________________________________8

4.4 Setting / Overchecking the Timing Position_______________________________________________9

4.5 Downloading an Alternate Language ___________________________________________________9

5. SPARES AND SERVICE ________________________________________________________________11

5.1 YDT262 Spares ___________________________________________________________________11

5.2 Related Parts/Tools ________________________________________________________________11

5.3 Troubleshooting ___________________________________________________________________11

FRANCAIS_____________________________________________________________________________13

AVANT-PROPOS ________________________________________________________________________13

1. INTRODUCTION _____________________________________________________________________14

2. DÉFINITION DES EXPRESSIONS ET ABRÉVIATIONS ___________________________________________14

3. PRINCIPLE DE FONCTIONNEMENT _______________________________________________________14

4. FONCTIONNEMENT __________________________________________________________________15

4.1 Agencement ______________________________________________________________________15

4.2 Installation _______________________________________________________________________15

4.3 Séquence d'utilisation du logiciel______________________________________________________16

4.4 Réglage / Surcontrôle de la position de distribution _______________________________________17

4.5 Téléchargement d'une autre langue ____________________________________________________17

5. PIÈCES DE RECHANGE ET RÉPARATIONS __________________________________________________20

5.1 Pièces de rechange pour le YDT262 ___________________________________________________20

5.2 Pièces connexes/Outillages __________________________________________________________20

5.3 Dépistage des anomalies ____________________________________________________________20

DEUTSCH _____________________________________________________________________________21

VORWORT_____________________________________________________________________________21

1. EINFÜHRUNG ______________________________________________________________________22

2. DEFINITION VON BEZEICHNUNGEN UND ABKÜRZUNGEN _____________________________________22

3. BETRIEBSPRINZIP ___________________________________________________________________22

4. BETRIEB ____________________________________________________________________________23

4.1 Layout __________________________________________________________________________23

4.2 Montage _________________________________________________________________________24

4.3 Betriebsabfolge der Software_________________________________________________________24

4.4 Einstellung / Überprüfen der Timingposition ____________________________________________25

4.5 Herunterladen einer zusätzlichen Sprache_______________________________________________25

5. ERSATZTEILE UND KUNDENDIENST________________________________________________________28

5.1 Ersatzteile für das YDT262 __________________________________________________________28

5.2 Dazugehörige Teile/Werkzeuge _______________________________________________________28

5.3 Fehlersuche ______________________________________________________________________28

ESPAÑOL______________________________________________________________________________29

PREFACIO _____________________________________________________________________________29

1. INTRODUCCIÓN_____________________________________________________________________30

2. DEFINICIÓN DE TÉRMINOS Y ABREVIACIONES ______________________________________________30

3. PRINCIPIO DE FUNCIONAMIENTO________________________________________________________30

4. FUNCIONAMIENTO ____________________________________________________________________31

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

YDT262 Operating and Servicing Manual DELPHI DIESEL AFTERMARKET

4 HL018, Issue 2

4.1 Disposición ______________________________________________________________________ 31

4.2 Instalación_______________________________________________________________________ 31

4.3 Secuencia de funcionamiento del programa _____________________________________________ 32

4.4 Ajuste y verificación de las posiciones de tiempos ________________________________________ 33

4.5 Carga de un idioma alternativo ______________________________________________________ 33

5. REPUESTOS Y MANTENIMIENTO __________________________________________________________ 35

5.1 Repuestos para el controlador YDT262 ________________________________________________ 35

5.2 Componentes y herramientas auxiliares ________________________________________________ 35

5.3 Localización y solución de problemas _________________________________________________ 35

ITALIANO ____________________________________________________________________________ 37

1. INTRODUZIONE_____________________________________________________________________ 38

2. DEFINIZIONE DEI TERMINI E ABBREVIAZIONI ______________________________________________ 38

3. PRINCIPIO OPERATIVO _______________________________________________________________ 38

4. FUNZIONAMENTO_____________________________________________________________________ 39

4.1 Disposizione _____________________________________________________________________ 39

4.2 Installazione _____________________________________________________________________ 39

4.3 Sequenza operativa del Software _____________________________________________________ 40

4.4 Impostazione /Controllo della posizione di fasatura_______________________________________ 41

4.5 Trasferimento di una lingua alternativa ________________________________________________ 41

5. RICAMBI E ASSISTENZA ________________________________________________________________ 43

5.1 Ricambi YDT262__________________________________________________________________ 43

5.2 Parti / Attrezzi ____________________________________________________________________ 43

5.3 Ricerca guasti ____________________________________________________________________ 43

PORTUGES____________________________________________________________________________ 45

PREFÁCIO_____________________________________________________________________________ 45

1. INTRODUÇÃO ______________________________________________________________________ 46

2. DEFINIÇÃO DOS TERMOS E ABREVIATURAS _______________________________________________ 46

3. PRINCÍPIO DE FUNCIONAMENTO________________________________________________________ 46

4. OPERAÇÃO __________________________________________________________________________ 47

4.1 Disposição_______________________________________________________________________ 47

4.2 Instalação _______________________________________________________________________ 48

4.3 Sequência Operacional do Software ___________________________________________________ 48

4.4 Regulação / Verificação da Posição de Ponto ___________________________________________ 49

4.5 Carregamento de outra Língua ______________________________________________________ 49

5. PEÇAS SOBRESSALENTES E SERVIÇO ______________________________________________________ 51

5.1 Peças sobressalentes YDT262________________________________________________________ 51

5.2 Peças/Ferramentas Relacionadas_____________________________________________________ 51

5.3 Solução de Problemas______________________________________________________________ 51

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

DELPHI DIESEL AFTERMARKET YDT262 Operating and Servicing Manual

HL018, Issue 2 5

ENGLISH

Foreword

DT Assembly & Test - Europe Ltd. reserves the copyright of all information and illustrations in this

publication which is supplied in confidence and which may not be used for any other purpose other

than that for which it was originally supplied. The publication may not be reproduced in part or in

whole without the consent in writing of this company.

Safety Information

The YDT262 is used in conjunction with a host test bench. Basic safety rules and precautions for

operating the host test bench should be observed.

Warnings, Cautions and Notes

The precautionary notes in this publication, indicated by the words WARNING, CAUTION, or NOTE

provide information about potential hazards to personnel or equipment. Ignoring these notes may

lead to serious injury to personnel and/or damage to equipment. These notes appear as follows:

WARNING! INDICATES THAT A SITUATION MAY BE HAZARDOUS TO PERSONNEL.

INSTRUCTIONS ARE PROVIDED FOR AVOIDING PERSONAL INJURY.

CAUTION! Indicates that conditions exist that could result in damage to equipment.

Instructions are provided to prevent equipment damage.

NOTE Indicates additional information for clarification where there may be confusion.

General Warnings

Ensure good levels of lighting for safe, efficient equipment operation.

Accidents can occur to unauthorised personnel during testing. Untrained

person(s) must not be present in the test area when the equipment is operating.

Only qualified personnel are to operate this equipment.

This equipment contains electrostatic sensitive devices. Observe the necessary

precautions for handling electrostatic discharge sensitive devices. Do not touch

printed circuit boards and associated electronic connections and components.

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

YDT262 Operating and Servicing Manual DELPHI DIESEL AFTERMARKET

6 HL018, Issue 2

1. Introduction

The Dynamic Timing Control Box (YDT262) is used to determine the timing position of diesel fuel

injection pumps. It is used in conjunction with a host test bench (to mount and drive the fuel pump), a

rotary encoder (providing angular position information), and a piezo pickup (giving the point of

injection signal).

2. Definition of Terms and Abbreviations

The following terms and abbreviations are used in this manual and/or in the YDT262 software.

SP Start Position. The box records a reference point for starting position (effectively

0 degrees). This is used later when calculating the Overcheck Angle.

Offset The angular offset to be applied from the point of injection to the locking position.

Trigger Level The piezo signal trigger level at which the angular position is recorded.

POI Point of Injection

RLP Required Locking Position. This is equal to POI plus/minus the Offset.

Overcheck Angle The difference between SP and RLP.

3. Principle of Operation

The rotary encoder is mounted on the pump drive coupling and the piezo pickup is connected to one

of the pump delivery valves. The piezo pickup provides a signal once every revolution at the point of

injection. By comparing this signal with the angular position information from the rotary encoder, the

point of injection angle is found.

The actual position is found by taking a number of samples at a given speed. The software then

calculates the average position and, once the drive has been stopped, provides you with an angular

countdown so that you can rotate the pump around to that position.

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

DELPHI DIESEL AFTERMARKET YDT262 Operating and Servicing Manual

HL018, Issue 2 7

4. Operation

4.1 Layout

Figure 4.1: Top View

Figure 4.1 Key:

1 2*20 display

2 Up (), Down (), and Enter () buttons

3 Piezo socket

4 Encoder socket

Figure 4.2: Bottom View

Figure 4.2 Key:

1 IEC Power inlet socket (accepts a range of standard connector leads).

2 On/Off Switch

3 120V/240V selector for nominal 115V/230V 50/60Hz AC single phase supply.

4 Power input fuse (2A anti-surge, 20mm*5mm)

5 RS232 connection

4.2 Installation

The YDT262 requires a standard IEC single-phase power lead, to be purchased locally. An EMC

shielding ferrite is supplied with the kit. Clip the ferrite onto the single-phase power lead as shown in

Figure 4.3.

CAUTION Set the 120V/240V voltage selector switch (Item 3, Figure 4.2) to the correct setting

for the local voltage.

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

YDT262 Operating and Servicing Manual DELPHI DIESEL AFTERMARKET

8 HL018, Issue 2

Figure 4.3: Clip-on Ferrite

The YDT262 is designed to hang on the rim of the test stand. If using with Pumpmaster, AVM, or

PGM test stands, the additional adapter bracket will also be required.

4.3 Software Operating Sequence

The operating sequence for the box together with examples of the screen displays is given below.

Operating Step

Display Example

Power on

The display shows the version number and the last-used language.

Press Up/Down buttons to change language. Press Enter to

confirm and move on; the box records SP at this point.

VERSION 1.0

ENGLISH

Zero Angle Confirmation

The software confirms that the zero angle (SP) has been recorded.

Up/Down buttons disabled. Press Enter to confirm and move on.

If unsuccessful, the message “ZERO ANGLE ERROR” will be

displayed and all buttons will be disabled –refer to Section 5.3

Troubleshooting.

ZERO ANGLE

RECORDED

Offset Value

Display shows last-used offset value. Press Up/Down buttons to

change, scroll from 0.0 to 359.9in steps of 0.1. Press Enter to

confirm and move on.

OFFSET: 0.0 DEG

Trigger level setting

Display shows last-used trigger level. Press Up/Down buttons to

change –the following levels are available: 25%, 50%, 72%, 75%

of peak voltage, or 100mV, 200mV, 400mV, 800mV. Press Enter to

confirm and move on.

TRIGGER LEVEL:

25%

Variation

Display shows the angle between piezo signals. This gives an

indication of any problems with the input signals (it should read

360when the pump is running at constant speed). Press Enter

when value is stable and ready to test. Up/down buttons disabled.

VARIATION

359.8 DEG

Sampling

The box takes 100 samples of the piezo position, then calculates

RLP. All buttons are disabled during learning.

SAMPLING…

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

DELPHI DIESEL AFTERMARKET YDT262 Operating and Servicing Manual

HL018, Issue 2 9

When complete, the display shows:

Press Enter to move on. Up/down buttons disabled.

PLEASE STOP

TEST BENCH

Overcheck Angle

The display shows the Overcheck Angle. Press Enter to move on.

Up/down buttons disabled.

OVERCHECK ANGLE:

2.10 DEG

Setting

The display shows the angle between the current position and RLP

(in direction of rotation). As the drive is rotated (by hand) the angle

displayed counts down to 0.

Up/down buttons disabled. Enter returns to offset screen.

ROTATE TO ZERO:

123.04 DEG

4.4 Setting / Overchecking the Timing Position

For details on setting and overchecking the timing position, refer to Delphi Service Instruction Note

number DT339.

4.5 Downloading an Alternate Language

The YDT262 is supplied pre-loaded with the following languages: English, French, German, Italian,

Spanish, and Portuguese. There is additional space allocated in the memory for one extra language,

which can be downloaded into the YDT262 from a PC.

When there is no additional language loaded the message “USER NOT AVALABLE” will appear when

you scroll through the languages. To escape from this message, press the Enter button.

To download an alternate language you will need the following:

Any PC with a serial communications program, e.g. Terminal or HyperTerminal (these are

standard programs supplied with Windows 3.x, 95, 98, and NT).

A standard 9-way D female to 9-way D female serial cable, e.g. RS Components part no. 215-

410.

Before downloading, you need to create the alternate language messages as a text file. An example

text file is given below (with English messages). Open Notepad and copy this example file,

translating where required. Note that each line can only have 20 characters maximum. Put 2

semicolons on the last line of the file as given in the example. Save the file and close Notepad.

Example language text file:

ENGLISH

FRENCH

GERMAN

ITALIAN

SPANISH

PORTUGUESE

USER

VERSION 1.2

TRIGGER LEVEL:

OFFSET:

DEG

VARIATION

SAMPLING...

PLEASE STOP

TEST BENCH

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

YDT262 Operating and Servicing Manual DELPHI DIESEL AFTERMARKET

10 HL018, Issue 2

OVERCHECK ANGLE

ROTATE TO ZERO

DEG

SEND TEXT

READY

USER NOT AVAILABLE

ZERO ANGLE

RECORDED

ZERO ANGLE

ERROR

;;

The procedure below refers to HyperTerminal. Other programs will be similar –the important

information is the COM port setup given in steps 4 and 5; refer to the operating instructions for your

particular program to set these.

1. Connect the cable between the YDT262 and one of the PC COM ports. Do not switch on the

YDT262 yet.

2. The first time you use HyperTerminal you will need to configure the communication settings. To

do this, open HyperTerminal (Start > Programs > Accessories > HyperTerminal > HyperTerminal).

It will assume you are making a new connection. Enter a name for the connection, e.g. YDT262,

choose an icon, then press OK.

3. In the next box select the COM port you are using and press OK.

4. In the next box, configure the port as follows, and then press OK. Baud: 9600; Data Bits: 8;

Parity: None; Stop Bits: 1; Flow Control: None.

5. Under ASCII setup (File, Properties, Settings, ASCII Setup), ensure that the “Send line ends with

line feeds” option is selected, then click OK twice to return to the main screen.

6. Choose File, Save. This saves the connection information as a HyperTerminal file, and puts a

link to it on the Start menu. Next time, you can just click on this link (Start > Programs >

Accessories > HyperTerminal > YDT262.ht) and it will open HyperTerminal with the correct

settings.

7. Switch on the YDT262 while holding down the Up and Down buttons. The message “SEND

TEXT” will appear on the display. You are now ready to transfer the language file.

8. In HyperTerminal select Transfer, Send Text File, and then browse to find your language text file

and select Open.

9. When the download is complete, the box will display “READY”. Press Enter to return to normal

operating mode.

THIS IS AN UNCONTROLLED DOCUMENT downloaded by Lukas Matuska on 16 Feb 2016

Any technical intervention requires certified Hartridge training. Contact Hartridge Ltd for details.

Inhaltsverzeichnis

Sprachen:

Andere Delphi Controller Handbücher

Delphi

Delphi EZ-Pro 15-6 Kiln Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung