Delta Electronics Delphi S48SS Series Bedienungsanleitung

DS_S48SS12001_06082006

DATASHEET

DS_S48SS12001_06082006

Delta Electronics, Inc.

 Telecom/DataCom

 Wireless Networks

 Optical Network Equipment

 Server and Data Storage

 Industrial/Test Equipment

Delphi Series S48SS, 15W Family

DC/DC Power Module: 48V in, 12V/1.25A out

The Delphi Series S48SS, surface mountable, 48V input, single output,

isolated DC/DC converter, is the latest offering from a world leader in

power system and technology and manufacturing－Delta Electronics,

Inc. This product family provides up to 15 watts of power or up to 4.5A

of output current (for 3.3V and below) in an industry standard footprint.

With creative design technology and optimization of component

placement, the Delphi Series Small Power converters possess

outstanding electrical and thermal performance, as well as extremely

high reliability under highly stressful operating conditions. All models

are protected from abnormal input/output voltage and current

conditions. An encapsulated version is available for the most robust

performance in harsh environments.

Applications

FEATURES

 High efficiency: 86.5% @ 12V/1.25A

 Standard footprint

 Surface mountable

 Industry standard pin out

 Low profile: 0.48”

 Fixed frequency operation

 Input UVLO, Output OCP, OVP

 No minimum load required

 2:1 input voltage range

 ISO 9001, TL 9000, ISO 14001, QS

9000, OHSAS 18001 certified

manufacturing facility

 UL/cUL 60950 (US & Canada)

Recognized, and TUV (EN60950)

Certified

 CE mark meets 73/23/EEC and

93/68/EEC directives

DS_s48SS12001_06082006

TECHNICAL SPECIFICATIONS

(TA=25°C, airflow rate=300 LFM, Vin=48Vdc, nominal Vout unless otherwise noted.)

PARAMETER NOTES and CONDITIONS S48SS12001NRFA

Min. Typ. Max. Units

ABSOLUTE MAXIMUM RATINGS

Input Voltage

Continuous 80 Vdc

Transient (100ms) 100ms 100 Vdc

Operating Temperature Refer to Figure 12 for the measuring point -40 100 °C

Storage Temperature -55 125 °C

Input/Output Isolation Voltage 1 minute 1500 Vdc

INPUT CHARACTERISTICS

Operating Input Voltage 36 48 75 V

Input Under-Voltage Lockout

Turn-On Voltage Threshold 33.8 34.5 35.8 V

Turn-Off Voltage Threshold 32.0 33.5 34.5 V

Lockout Hysteresis Voltage 0.5 1.5 2.5 V

Maximum Input Current 100% Load, 36Vin 0.6 A

No-Load Input Current 25 mA

Off Converter Input Current 1 m

Inrush Current(I2t) 0.01 A2s

Input Reflected-Ripple Current P-P thru 12µH inductor, 5Hz to 20MHz 5 mA

Input Voltage Ripple Rejection 120 Hz 55 dB

OUTPUT CHARACTERISTICS

Output Voltage Set Point Vin=48V, Io=50% Io, max, Tc=25℃11.76 12.00 12.24 V

Output Voltage Regulation

Over Load Io=Io,min to Io,max ±12 ±60 mV

Over Line Vin=36V to 75V ±12 ±36 mV

Over Temperature Tc=-40℃to 100℃100 300

m/℃

Total Output Voltage Range Over sample load, line and temperature TBD TBD V

Output Voltage Ripple and Noise 5Hz to 20MHz bandwidth

Peak-to-Peak Full Load, 1µF ceramic, 10µF tantalum 50 100 mV

RMS Full Load, 1µF ceramic, 10µF tantalum 15 25 mV

Operating Output Current Range 0 1.25 A

Output DC Current-Limit Inception Output Voltage 10% Low 1.5 2 2.5 A

DYNAMIC CHARACTERISTICS

Output Voltage Current Transient 48V, 10µF Tan & 1µF Ceramic load cap, 0.1A/µs

Positive Step Change in Output Current 50% Io, max to 75% Io, max 100 240 mV

Negative Step Change in Output Current 75% Io, max to 50% Io, max 100 240 mV

Setting Time to 1% of Final Value 600 µs

Turn-On Transient

Start-Up Time, From On/Off Control 35 50 ms

Start-Up Time, From Input 35 50 ms

Maximum Output Capacitance Full load; 5% overshoot of Vout at startup 47 µF

EFFICIENCY

100% Load 84 86.5 %

ISOLATION CHARACTERISTICS

Isolation Voltage 1500 V

Isolation Resistance 100 MΩ

Isolation Capacitance 500 pF

FEATURE CHARACTERISTICS

Switching Frequency 260 kHz

ON/OFF Control, (Logic Low-Module ON)

Logic Low Von/off at Ion/off=1.0mA 0 0.8 V

Logic High Von/off at Ion/off=0.0 µA 15 V

ON/OFF Current Ion/off at Von/off=0.0V 1 mA

Leakage Current Logic High, Von/off=15V 50 µA

Output Voltage Trim Range Across Trim Pin & +Vo or -Vo, Pout≦max rated power -10 +10 %

Output Over-Voltage Protection Over full temp range; % of nominal Vout 115 125 140 %

GENERAL SPECIFICATIONS

Calculated MTBF Io=80% of Io, max; Tc=40°C 3 M hours

Weight 12.5 grams

DS_s48SS12001_06082006

ELECTRICAL CHARACTERISTICS CURVES

0.25 0.5 0.75 1 1.25

OUTPUT CURRENT (A)

EFFICIENCY (%)

36Vin 48Vin 75Vin

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

0.25 0.5 0.75 1 1.25

OUTPUT CURRENT (A)

POWER DISSIPATION (W

Figure 1: Efficiency vs. load current for minimum, nominal, and

maximum input voltage at 25°C. Figure 2: Power dissipation vs. load current for minimum,

nominal, and maximum input voltage at 25°C.

0.0

0.1

0.2

0.3

0.4

0.5

0.6

30 35 40 45 50 55 60 65 70 75

INPUT VOLTAGE (V)

INPUT CURRENT (A)

Io=1.25A Io=0.75A

Io=0.125A

Figure 3: Typical input characteristics at room temperature.

Figure 4: Turn-on transient at full rated load current (resistive

load) (10 ms/div). Top Trace: Vout (5V/div); Bottom Trace:

ON/OFF Control (2V/div).

36Vin 48Vin 75Vin

)

DS_s48SS12001_06082006

ELECTRICAL CHARACTERISTICS CURVES

Figure5: Turn-on transient at zero load current (10 ms/div). Top

Trace: Vout (5V/div); Bottom Trace: ON/OFF Control (2V/div).

Figure 6: Output voltage response to step-change in load

current (50%-75%-50% of Io, max; di/dt = 0.1A/µs). Load

cap: 10µF, 100 m

Ω



ESR tantalum capacitor and 1µF

ceramic capacitor. Top Trace: Vout (50mV/div), Bottom

Trace: Iout (0.5A/div).

20﹫100KHz℃20 ℃100KHz﹫

Ω

ESR< 0.3 ESR< 0.3

TEST

12uH

Cs:68uF/100V 68uF/100V

Vi(-)

Vi(+)

Ω

Figure 7: Test set-up diagram showing measurement points for

Input Reflected Ripple Current (Figure 8).

Note: Measured input reflected-rip

le current with a simulated

source Inductance (LTEST

)

of 12 µH. Capacitor Cs offset possible

battery impedance.

Figure 8: Input Reflected Ripple Current, is, at full rated

output current and nominal input voltage with 12µH source

impedance and 68µF electrolytic capacitor (2 mA/div)

DS_s48SS12001_06082006

ELECTRICAL CHARACTERISTICS CURVES

StripCopper

Vo(-)

Vo(+)

10u 1u SCOPE RESISTIV

LOAD

Figure 9:Output voltage noise and ripple measurement test

setup. Scope measurement should be made using a BNC

cable (length shorter than 20 inches).Position the load

between 51 mm to 76 mm (2 inches to 3 inches) from the

module.

Figure 10: Output voltage ripple at nominal input voltage and

rated load current (20 mV/div). Load capacitance: 1µF ceramic

capacitor and 10µF tantalum capacitor. Bandwidth: 20 MHz.

0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

0.0 0.5 1.0 1.5 2.0 2.5

LOAD CURRENT (A)

OU TPUT VOLTAGE (V)

Vin= 48V

Figure 11: Output voltage vs. load current showing typical

current limit curves and converter shutdown points.

DS_s48SS12001_06082006

Figure 14: Output current vs. ambient temperature and air velocity

(Vin=75V) Figure 15: Power dissipation vs. ambient temperature and air

velocity.

S48SS12001NR A Power Dissipation vs. Ambient Temperature and Air Velocity

0.0

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

2.2

2.4

2.6

2.8

3.0

3.2

70 75 80 85 90 95 100 105

Ambient Temperature (℃)

Power Dissipation (Watts)

100LFM

200LFM

300LFM

400LFM

600LFM

Natural

Convection 500LFM

S48SS12001NR A Output Current vs. Ambient Temperature and Air Velocity @Vin = 75V

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

70 75 80 85 90 95 100

Ambient Temperature (℃)

Output Current(A)

100LFM

300LFM

400LFM

600LFM

Natural

Convection

200LFM

500LFM

Figure 12: Case temperature measurement location. Pin locations are

for reference only. Figure 13: Output current vs. ambient temperature and air velocity (Vin

<60V)

THERMAL CURVES:

Top View

S48SS12001NR A Output Current vs. Ambient Temperature and Air Velocity @Vin < 60V

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

75 80 85 90 95 100 105

Ambient Temperature (℃)

Output Current(A)

600LFM

400LFM

200LFM

100LFM

Natural

Convection

300LFM

500LFM

DS_s48SS12001_06082006

DESIGN CONSIDERATION

Input Source Impedance

The impedance of the input source connecting to the

DC/DC power modules will interact with the modules

and affect the stability. A low ac-impedance input

source is recommended. If the source inductance is

more than a few µH, we advise adding a 10 to 100 µF

electrolytic capacitor (ESR < 0.7 Ωat 100 kHz)

mounted close to the input of the module to improve the

stability.

Layout and EMC Considerations

Delta’s DC/DC power modules are designed to operate

in a wide variety of systems and applications. For

design assistance with EMC compliance and related

PWB layout issues, please contact Delta’s technical

support team. An external input filter module is

available for easier EMC compliance design.

Application notes to assist designers in addressing

these issues are pending release.

Safety Considerations

The power module must be installed in compliance with

the spacing and separation requirements of the end-

user’s safety agency standard if the system in which the

power module is to be used must meet safety agency

requirements.

When the input source is 60Vdc or below, the power

module meets SELV (safety extra-low voltage)

requirements. If the input source is a hazardous voltage

which is greater than 60 Vdc and less than or equal to

75 Vdc, for the module’s output to meet SELV

requirements, all of the following must be met:

 The input source must be insulated from any

hazardous voltages, including the ac mains, with

reinforced insulation.

 One Vi pin and one Vo pin are grounded, or all the

input and output pins are kept floating.

 The input terminals of the module are not operator

accessible.

 A SELV reliability test is conducted on the system

where the module is used to ensure that under a

single fault, hazardous voltage does not appear at

the module’s output.

Do not ground one of the input pins without grounding

one of the output pins. This connection may allow a non-

SELV voltage to appear between the output pin and

ground.

This power module is not internally fused. To achieve

optimum safety and system protection, an input line

fuse is highly recommended. The safety agencies

require a normal-blow fuse with 1A maximum rating to

be installed in the ungrounded lead. A lower rated fuse

can be used based on the maximum inrush transient

energy and maximum input current.

Soldering and Cleaning Considerations

Post solder cleaning is usually the final board assembly

process before the board or system undergoes electrical

testing. Inadequate cleaning and/or drying may lower

the reliability of a power module and severely affect the

finished circuit board assembly test. Adequate cleaning

and/or drying is especially important for un-encapsulated

and/or open frame type power modules. For assistance

on appropriate soldering and cleaning procedures,

please contact Delta’s technical support team.

DS_s48SS12001_06082006

Vo(+)

Vo(-)

Trim

Rtrim-up

Figure 17: Circuit configuration for trim-up (increase output

voltage)

If the external resistor is connected between the TRIM

and Vo - the output voltage set point increases. The

external resistor value required to obtain a percentage

output voltage change △Vo% is defined as:

[]

ΚΩ−

−∆

=− 32.3

07.0Vo12 668.25

upRtrim

Ex. When trim-up +10% (12V X 1.1 = 13.2V)

[]

ΚΩ=−

−×

=− 39.1932.3

07.01.012 668.25

upRtrim

Care should be taken to ensure that the maximum

output power of the module remains at or below the

maximum rated power.

Remote ON/OFF

The remote on/off feature on the module can be either

negative or positive logic. Negative logic turns the

module on during a logic low and off during a logic high.

Positive logic turns the modules on during a logic high

and off during a logic low. Remote on/off can be

controlled by an external switch between the on/off

terminal and the Vi(-) terminal. The switch can be an

open collector or open drain. If the remote on/off feature

is not used, please short the on/off pin to Vi(-) for

negative logic and let the pin open for positive logic.

ON/OFF

Vi(-)

Vi(+) Vo(+)

Trim

Vo(-)

Figure 18: Circuit Configuration for Remote ON/OFF

FEATURES DESCRIPTIONS

Over-Current Protection

The modules include an internal output over-current

protection circuit, which will endure current limiting for

an unlimited duration during output overload. If the

output current exceeds the OCP set point, the modules

will automatically shut down (hiccup mode).

The modules will try to restart after shutdown. If the

overload condition still exists, the module will shut down

again. This restart trial will continue until the overload

condition is corrected.

Over-Voltage Protection

The modules include an internal output over-voltage

protection circuit, which monitors the voltage on the

output terminals. If this voltage exceeds the over-

voltage set point, the module will shut down and latch

off. The over-voltage latch is reset by cycling the input

power or by togging the ON/OFF signal for one second.

Output Voltage Adjustment (TRIM)

To increase or decrease the output voltage set point, the

modules may be connected with an external resistor

between the TRIM pin and either the Vo+ or Vo -. The

TRIM pin should be left open if this feature is not used.

Vo(+)

Vo(-)

Trim trim-down

Figure 16: Circuit configuration for trim-down (decrease output

voltage)

If the external resistor is connected between the TRIM

and Vo+ pins, the output voltage set point decreases.

The external resistor value required to obtain a

percentage of output voltage change △Vo% is defined

as:

[]

ΚΩ−

+∆

∆−

=− 32.3

07.0Vo12 Vo4.248732.222

downRtrim

Ex. When trim-down –10% (12V X 0.9 =10.8V)

[]

ΚΩ=−

+×

×−

=− 50.15232.3

07.01.012 1.04.248732.222

downRtrim

DS_s48SS12001_06082006

THERMAL CONSIDERATIONS

Thermal management is an important part of the system

design. To ensure proper, reliable operation, sufficient

cooling of the power module is needed over the entire

temperature range of the module. Convection cooling is

usually the dominant mode of heat transfer.

Hence, the choice of equipment to characterize the

thermal performance of the power module is a wind

tunnel.

Thermal Testing Setup

Delta’s DC/DC power modules are characterized in

heated vertical wind tunnels that simulate the thermal

environments encountered in most electronics

equipment. This type of equipment commonly uses

vertically mounted circuit cards in cabinet racks in which

the power modules are mounted.

The following figure shows the wind tunnel

characterization setup. The power module is mounted

on a test PWB and is vertically positioned within the

wind tunnel. The space between the neighboring PWB

and the top of the power module or a heat sink is

6.35mm (0.25”).

Thermal Derating

Heat can be removed by increasing airflow over the

module. Figure 13 and 14 show maximum output is a

function of ambient temperature and airflow rate. The

module’s maximum case temperature is +100°C. To

enhance system reliability, the power module should

always be operated below the maximum operating

temperature. If the temperature exceeds the maximum

module temperature, reliability of the unit may be

affected.

Figure 19: Wind tunnel test setup

Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)

10 (0.4”)

MODULE

IR FLOW

50.8

(

2.0”

)

FACING PWB PWB

AIR VELOCIT

AND AMBIENT

TEMPERATURE

MEASURED BELOW

THE MODULE

DS_s48SS12001_06082006

MECHANICAL DRAWING

Pin No. Name Function

1 +Vout Positive output voltage

2 -Vout Negative output voltage

3 Trim Output voltage trim

4 NC No Connection

5 NC No Connection

6 NC No Connection

7 NC No Connection

8 ON/OFF ON/OFF Logic

9 NC No Connection

10 NC No Connection

11 -Vin Negative input voltage

12 +Vin Positive input voltage

Andere Handbücher für Delphi S48SS Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Delta Electronics Stromversorgung Handbücher

Delta Electronics

Delta Electronics Delphi E48SC Bedienungsanleitung

Delta Electronics

Delta Electronics DPS-200PB-127 Bedienungsanleitung

Delta Electronics

Delta Electronics E48SH Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi IPM24S0B0 Bedienungsanleitung

Delta Electronics

Delta Electronics 0.75-3.3V Bedienungsanleitung

Delta Electronics

Delta Electronics DPS-350QB Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi S48SP Bedienungsanleitung

Delta Electronics

Delta Electronics PFC Choke PFC3520V Series Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi Q48DM Bedienungsanleitung

Delta Electronics

Delta Electronics DPS-250WB Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi S36SE Bedienungsanleitung

Delta Electronics

Delta Electronics TAP-CP01 Bedienungsanleitung

Delta Electronics

Delta Electronics Q48SB Bedienungsanleitung

Delta Electronics

Delta Electronics PMC-24V050W1AA Bedienungsanleitung

Delta Electronics

Delta Electronics CMC-DN01 Bedienungsanleitung

Delta Electronics

Delta Electronics GPS-450EB EA22 Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi E48SR12007 Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi MCM12S03L A Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi H48SV Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi S48SR Series Bedienungsanleitung

Delta Electronics

Delta Electronics PMC-12V035W1AA Bedienungsanleitung

Delta Electronics

Delta Electronics Delphi NE Series Bedienungsanleitung

Delta Electronics

Delta Electronics SM3300 Series Bedienungsanleitung

Delta Electronics

Delta Electronics DPS-180KB-4 Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung