Delta Electronics N Series Bedienungsanleitung

www.deltapowersolutions.com

Delta UPS - Amplon Family

User Manual

The power behind competitiveness

N Series, Single Phase

1/2/3 kVA

Save This Manual

This manual contains important instructions and warnings that you should

follow during the installation, operation, storage and maintenance of this

product. Failure to heed these instructions and warnings will void the

warranty.

this User Manual (“Manual”), including but not limited to the contents, infor-

mation, and figures are solely owned and reserved by Delta Electronics Inc.

(“Delta”). The Manual can only be applied to the operation or the use of this

product. Any disposition, duplication, dissemination, reproduction, modiﬁcation,

translation, extraction, or usage of this Manual in whole or in part is prohibited

without the prior written permission of Delta. Given that Delta will continuously

improve and develop the product, changes may be made to the information in

this Manual at any time without obligation to notify any person of such revision

or changes. Delta will make all possible efforts to secure the accuracy and the

integrity of this Manual. Delta disclaims any kinds or forms of warranty, guaran-

tee, or undertaking, either expressly or implicitly, including but not limited to the

completeness, faultlessness, accuracy, non-infringement, merchantability or ﬁt-

ness for a particular purpose of the Manual.

CONTENTS

Chapter 1. IMPORTANT SAFETY INSTRUCTIONS......................... 1

1-1 safety instructions............................................................................. 1

Chapter 2. INTRODUCTION ............................................................. 3

2-1 Theory of operation .......................................................................... 3

2-2 Feature ............................................................................................. 4

2-3 Annotation and symbol..................................................................... 6

2-4 Front Panel ....................................................................................... 7

2-5 Operation Panel ............................................................................... 7

2-6 Rear Panel........................................................................................ 9

Chapter 3. INSTALLATION ............................................................. 10

3-1 Unpacking....................................................................................... 10

3-2 Before Installation........................................................................... 10

3-3 Installation....................................................................................... 11

Chapter 4. OPERATION.................................................................. 15

4-1 Cold start when utility is not present .............................................. 15

4-2 Turning “ON” the UPS.................................................................... 15

4-3 Turning “OFF” the UPS.................................................................. 15

4-4 UPS self-test................................................................................... 16

4-5 Silence function .............................................................................. 16

4-6 Abnormal Condition........................................................................ 16

4-7 UPS internal fault............................................................................ 18

4-8 Derating power ............................................................................... 18

Chapter 5. MAINTENANCE ............................................................ 19

Chapter 6. PLACEMENT................................................................. 19

Chapter 7. TROUBLESHOOTING .................................................. 20

Chapter 8. COMMUNICATION INTERFACE................................... 21

8-1 RS-232 ........................................................................................... 21

Chapter 9. Technical specifications.............................................. 22

1. IMPORTANT SAFETY INSTRUCTIONS

1-1 safety instructions

Please observe the following precautions to ensure personnel safety

and reliable equipment operation:

-The sound pressure level at the operators position according to IEC

704-1:1982 is equal or less than 70dB(A).

-Der arbeitsplatzbezogene Schalldruckpegel dieses Gerätes nach DIN

45635 beträgt 70dB (A) oder weniger.

For installation:

-The unit should be installed from service personnel.

-Dieses Gerät ist durch Elektrofachkräfte zu installieren.

-Upon installation, it should be ensured that the sum of the leakage

current of the UPS and the connected consumer does not exceed 3.5mA.

-Bei der Installation dieses Gerätes ist darauf zu achten, da£die

Ableitströme der USV und der angeschlossenen Verbraucher den

Maximalwert von 3.5 mA nicht überschreiten.

-The socket-outlet shall be near the equipment and easily accessible.

-Die Gerätesteckdose mu£nahe dem Gerät angebracht und leicht

zugänglich sein.

Other safety instructions:

-The UPS contains voltages which are potentially hazardous. All repairs

should be performed by qualified service personnel. The UPS has its own

internal energy source (Battery). The output receptacles may be alive

even when the UPS is not connected to the mains.

-Die USV enthält Spannungen die möglicherweise gefährlich sind. Alle

Reparaturen sollten nur von ausgebildeten Monteuren durchgeführt

werden. Die USV hat eine interne Stromversorgung (Batterien). Die

Ausgangsanschlüsse können daher unter Strom stehen auch wenn die

USV nicht an das Versorgungsnetz angeschlossen ist.

-When replacing batteries, always use the same type and quantity as the

previous one. Batteries of:

GES302N / 3KVA: HR9-12 (BB), HR1234WF2 (CSB)

GES202N / 2KVA: GP1270 or GP1272F2(CSB), BP7-12 or

BP7.2-12 (BB), NP7-12 (Yuasa), RT1270 (Ritar)

GES102N / 1KVA: GP1270 or GP1272F2 (CSB), BP7-12 or

BP7.2-12 (BB), NP7-12 (Yuasa), RT1270 (Ritar)

-Falls Sie die Batterien austauschen, verwenden Sie bitte ausschlie£lich

die gleiche Anzahl und die folgenden Batterietypen:

GES302N / 3KVA: HR9-12 (BB), HR1234WF2 (34W)

GES202N / 2KVA: GP1270 or GP1272F2(CSB), BP7-12 or

BP7.2-12 (BB), NP7-12 (Yuasa), RT1270 (Ritar)

GES102N / 1KVA: GP1270 or GP1272F2 (CSB), BP7-12 or

BP7.2-12 (BB), NP7-12 (Yuasa), RT1270 (Ritar)

-Do not dispose the battery or batteries in fire as this may explode.

-Werfen Sie niemals die Batterien in das Feuer, die Batterien könnten

explodieren.

-Do not open or mutilate the battery or batteries as released electrolyte is

toxic and harmful to skin and eyes.

-Öffnen oder beschädigen Sie nicht die Batterien, ausflie£endes

Elektrolyt ist schädlich für Haut und Augen.

-A battery can present a risk of electric shock and high short circuit current.

The following precaution should be observed when working on batteries.

Remove watches, rings or other metal objects.

Use tools with insulated handles.

-Eine Batterie kann eine Gefahr eines elektrischen Schlages und sehr gro

£er Kurzschlu£ströme beinhalten. Folgende Vorkehrungen sollten

getroffen werden, wenn Sie mit der Batterie arbeiten.

Entfernen Sie Uhren, Ringe und andere metallische Objekte.

Verwenden Sie Werkzeug mit isollierten Griffen.

-The equipment is to be operated by fully trained personnels.

-Diese Gerät ist nur durch unterwiesenes Personal zu bedienen.

EC conformity declaration

It is herewith confirmed to comply with the requirements set out in the

Council Directive on the Approximation of the Laws of the Member States

relating to Electromagnetic Compatibility Directive (2004/108/EC) and Low

Voltage Directive (2006/95/EC). For the evaluation of the compliance with

these Directives, the following standards were applied:

-EN 62040-1:2008

-EN 62040-2:2006

2. INTRODUCTION

2-1 Theory of operation

The main topology of the UPS consists of bypass path, AC-DC converter,

DC-AC inverter, battery charger, DC-DC converter, control circuit and

detection circuit. Moreover, the intelligent power management software is

also optional. The function and efficiency are superior to the traditional UPS.

Description of block diagram

Fig. 2.1 is the hardware block diagram of the UPS.

The UPS operation is described as below:

When the utility power is applied into the UPS, it was divided into two ways

after going through the breaker and EMI filter. One way is connected to

AC-DC converter which converts the utility AC power into a DC voltage which

is called DC-BUS voltage then divide into two path. One path goes to

charger which converts the DC-BUS voltage into a proper DC voltage to

charge the UPS battery. The other path goes into DC-AC half bridge inverter.

The other way works as a bypass path. The bypass relay near the output will

choose either the bypass path or inverter output. In general, the UPS will

internally do the self-diagnosis. If there is no problem, the bypass relay will

choose the inverter output. This is so calledǏON-LINE modeǐ.

PFC Control

Circuit

AC-DC Double

Booster

Charger DC-DC Converter

Auxiliary

Power

Half-bridge DC-AC Inverter

Control Board

EMI

Filter O/P

BYPASS

RELAY

BYPASS

To Control Board

LED Board

To Auxiliary Power

To Control Board

I/P

To Control Board

Battery Bank

To External Battery Bank

Relay

Breaker

In case the utility power fail, the AC-DC converter and charger will be off duty.

The DC-DC converter works and converts the battery voltage into DC-BUS

voltage. The DC-AC inverter converts the DC-BUS voltage into AC voltage.

This is so calledǏON-BATTERY modeǐ.

The auxiliary power circuit supplies the designated power to all the control

circuits. Because the DC-AC inverter is always working, the DC-DC

converter can work rapidly and replace the AC-DC converter while the utility

power fails. Furthermore, the bypass relay continuously keeps in the position

of inverter output to supply the regulated power for the load. There is no

power failure to loading equipment.

2-2 Feature

The UPS, available in 1KVA, 2KVA and 3KVA, is an advanced on-line UPS

providing reliable and consistent sine-wave quality power to vital equipment.

It supports personal computers, networks, servers, telecommunication

equipment and a variety of other facilities. With its outstanding protection

features, the unit keeps your applications safe and running smoothly at all

times.

PFC (Power Factor Correction)

With this function, the investment in the capacity of circuit breakers can beʳ

reduced, specially it will be highly regarded as an important feature in critical

load applications.

Complete Protection

On-line double conversion design, pure sine wave output and zero transfer

time provide best protection. With a built-in surge, spike and line noise

protection, the UPS prevents destructive hardware damage and extends

system life. The EMI/RFI filtering design prevents electrical noise from

affecting computer operation and data files. Besides, the UPS provides

built-in Fax/ Network cable (RJ11/RJ45) jacks protecting your hardware from

surge, spikes and line-noise that travel along communication lines, therefore

providing you a complete “back door” protection.

Intelligent design

Integrated with a microprocessor, the UPS is able to perform intelligent

functions. The UPS triggers over-voltage protection function and transfers to

ǏOn- Battery modeǐeven when utility voltage exceeds 280V for 220V Series.

In addition, the UPS can accept large voltage variation of 80V to 280V. Wide

input voltage range means less battery power usage frequency and longer

battery life-span. Besides, programmable outlet design, suitable for power

management, is also included in this unit.

Green function design

The operation in sleeping mode is designed to just keep charging which

saves the energy a lot.

User friendly interface

The UPS provides a variety of functions which meet users’ needs. Users can

instantly understand the status of the UPS via the informative LED display.

Audible alarms, bar meters and status indicators, such as battery replace

indication, UPS fault, line condition, overload etc. are simple and easy for

user to understand. Moreover, users can simply reset the circuit breaker

instead of having to replace a fuse in the event of output overload.

Safety approvals

The UPS has passed various safety regulations. CE mark and other safety

approvals, proves that the UPS is a safe reliable solution to your power

problems.

Network Management

Build-in communication interface port supporting RS232 protocols enhances

the reliability and manageability of the UPS over all major operating systems,

including Windows 95/98, Windows NT, Netware, Unix, and others.

2-3 Annotation and symbol

The two signs shown on the manual indicating important instruction need to

be followed.

Read before Operation Maybe Dangerous/Follow Instructions

PROTECTIVE GROUNDING TERMINAL: A terminal which must be

connected to earth ground prior to making any other connection to the

equipment.

This symbol indicates the word “phase”.

This symbol indicates the principal on/off switch is in the “ON” position.

This symbol indicates the principal on/off switch is in the “STANDBY”

position.

2-4 Front Panel

Fig 2-1.1 Front Panel for 1KVA Fig 2-1.2 Front Panel for 2KVA or 3KVA

2-5 Operation Panel

Operation panel

Operation Panel

A. 1 A. 2

B. 1

B. 2

B. 10

B. 11

B. 7

B. 6 B. 5

B. 8

B. 9

B. 3

B. 4

Fig 2-2 Operation Panel

Inhaltsverzeichnis

Andere Delta Electronics UPS Handbücher

Delta Electronics

Delta Electronics 7KVA Bedienungsanleitung

Delta Electronics

Delta Electronics Amplon Family Bedienungsanleitung

Delta Electronics

Delta Electronics GAIA Series Bedienungsanleitung

Delta Electronics

Delta Electronics E series Bedienungsanleitung

Delta Electronics

Delta Electronics DUPS-1232 Bedienungsanleitung

Delta Electronics

Delta Electronics INX-1K Bedienungsanleitung

Delta Electronics

Delta Electronics RT Series Bedienungsanleitung

Delta Electronics

Delta Electronics NH Plus Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung