Delta 80SF060J24 Bedienungsanleitung

www.delta-dct.com

VRF FLOOR STANDING INDOOR UNITS

80SF SERIES

INSTRUCTION MANUAL

WARNING!

Read and follow all safety precautions in

Instruction Manual - improper use can cause

serious injury.

Contents

1 Safety Precautions .......................................................................................... 1

2 Product Introduction ........................................................................................ 3

2.1 Outline of the Unit and Main Parts ............................................................. 3

2.2 Nominal Operating Condition ..................................................................... 3

2.3 Control Panel ............................................................................................. 4

3 Preparative for Installation............................................................................... 7

3.1 Standard Accessory Parts .......................................................................... 7

3.2 Selection of the Installation Location.......................................................... 7

3.3 Electrical Requirement ............................................................................... 9

4 Installation Instruction.................................................................................... 10

4.1 Installation of the Connection Pipe........................................................... 10

4.2 Installation and Test of Drain Pipe............................................................ 10

5 Introduction of DIP Switch ............................................................................. 12

5.1 Address Code........................................................................................... 12

5.2 Capacity Code.......................................................................................... 13

6 Wiring of Power Cord .................................................................................... 14

6.1 Wiring Precuations .................................................................................. 14

6.2 Electrical Wiring........................................................................................ 14

7 Test Running.................................................................................................. 16

8 Routine Maintenance..................................................................................... 17

8.1 Cleaning the Unit...................................................................................... 17

8.2 Cleaning the Air Filter .............................................................................. 17

9 Troubleshooting............................................................................................. 18

1 Safety Precautions

WARNING! This mark indicates procedures which, if improperly performed, might lead to

the death or serious injury of the user.

CAUTION! This mark indicates procedures which, if improperly performed, might possibly

result in personal harm to the user, or damage to property.

WARNING !

Installation should be left to the dealer or another professional. Improper installation may cause water

leakage, electrical shock, or re.

Install the air conditioner according to the instructions given in this manual. Incomplete installation may

cause water leakage, electrical shock, or re.

Be sure to use the supplied or specied installation parts. Use of other parts may cause the unit to

come to lose, water leakage, electrical shock, or re.

Install the air conditioner on a solid base that can support the weight of the unit. An inadequate base or

incomplete installation may cause injury in the event the unit falls off the base.

Electrical work should be carried out in accordance with the installation manual and the national

electrical wiring rules or code of practice. Insufcient capacity or incomplete electrical work may cause

electrical shock or re.

Be sure to use a dedicated power circuit. Never use a power supply shared by another appliance.

For wiring, use a cable length enough to cover the entire distance with no connection. Do not use an

extension cord. Do not put other loads on the power supply, use a dedicated power circuit. (Failure to

do so may cause abnormal heat, electric shock or re.)

Use the specified types of wires for electrical connections between the indoor and outdoor units.

Firmly clamp the interconnecting wires so their terminals receive no external stresses. Incomplete

connections or clamping may cause terminal overheating or re.

After connecting interconnecting and supply wiring be sure to shape the cables so that they do not

put undue force on the electrical covers or panels. Install covers over the wires. Incomplete cover

installation may cause terminal overheating, electrical shock, or re.

If any refrigerant has leaked out during the installation work, ventilate the room. (The refrigerant

produces a toxic gas if exposed to ames.)

After all installation is complete, check to make sure that no refrigerant is leaking out. (The refrigerant

produces a toxic gas if exposed to ames.)

When installing or relocating the system, be sure to keep the refrigerant circuit free from substances

other than the specified refrigerant (R410A), such as air. (Any presence of air or other foreign

substance in the refrigerant circuit causes an abnormal pressure rise or rupture, resulting in injury.)

During pump-down, stop the compressor before removing the refrigerant piping. If the compressor is

still running and the stop valve is open during pump-down, air will be sucked in when the refrigerant

piping is removed, causing abnormal pressure in the freezer cycle which will lead to breakage and

even injury.

During installation, attach the refrigerant piping securely before running the compressor. If the

compressor is not attached and the stop valve is open during pump-down, air will be sucked in when

the compressor is run, causing abnormal pressure in the freezer cycle which will lead to breakage and

even injury.

Be sure to establish an earth. Do not earth the unit to a utility pipe, arrester, or telephone earth.

Incomplete earth may cause electrical shock, or fire. A high surge current from lightning or other

sources may cause damage to the air conditioner.

Be sure to install an earth leakage breaker. Failure to install an earth leakage breaker may result in

electric shocks, or re.

CAUTION !

Do not install the air conditioner in a place where there is danger of exposure to inflammable gas

leakage. If the gas leaks and builds up around the unit, it may catch re.

Establish drain piping according to the instructions of this manual. Inadequate piping may cause

ooding.

Tighten the are nut according to the specied method such as with a torque wrench. If the are nut is

tightened too hard, the are nut may crack after a long time and cause refrigerant leakage.

2 Product Introduction

2.1 Outline of the Unit and Main Parts

Air outlet

Air inlet

E-HEATER

Speed Function Light Mode ON/OFF

Fig. 1

No. Part Name No. Part Name

①Air outlet ⑤Air inlet

②Control panel ⑥Drain pipe

③Wirless controller box ⑦Signal receiver

④Panel

2.2 Nominal Operating Condition

Item

Indoor Condition Outdoor Condition

DBTemperature°C WBTemperature°C DBTemperature°C WBTemperature°C

Rated Cooling 27 19 35 24

Rated Heating 20 15 7 6

2.3 Control Panel

E-HEATER

Speed Function Light Mode ON/OFF

Fig. 2

NOTE!

About the functions of “AUTO”, “AIR”, “ROOM’, “OFFICE”, “RESTAURANT”, and “COMMON”, they

are currently unavailable for this unit but reserved.

2.3.1 Buttons on the Control Panel

Buttons on the control panel : ON/OFF, Mode, Light, ▲, ▼, Function, Speed

◆ON/OFF

Press this key to switch on/off the unit. Note: under the blow mode, the unit can be turned on

directly by pressing this key.

◆Mode

The mode will vary circularly as the following order by pressing this key:

COOL: it indicates the cooling status

DRY: it indicates the dehumidifying status and the fan runs at the low speed.

FAN: it indicates the fan status.

HEAT: it indicates the heating status. (Note: it is unavailable for the cooling only unit)

◆Light

It switches on/off the lights on the control panel (expect the running and power indicating lights)

and “88”LED.

◆Function

(1) Under “ON” status, it can switch functions among up/down SWING, left/right SWING,

BLOW, E-HEATER, TIMER, AIR, SLEEP, SAVE, SET, and TEMP by pressing this key, and

then set the corresponding function by pressing ▲/▼, and then make a conrmation either

by pressing “Function” button or with no operation in 5 seconds.

(2) After some function is selected, if there is no “Turn-off” operation or there is no remote

control signal within two minutes, then press this key again to start circular function selection

from previous setting function.. Two minutes later or if there is “Turn-off” operation or there

is a remote control signal, then press this key again to start circular function selection from

the rst function..

◆▲/▼

(1) If there is no function setting, every press of ▲/▼ will increase/decrease setting temperature

by 1°C.The temperature range is 16~30°C.

(2) If there is some function setting, every press of ▲/▼ will switch the options of that function.

( the circulation by the press on the key ▲ and on the key ▼ is reverse).

• Up/Down SWING : There are two options, Swing On and Swing Off.

• Left/Right SWING : There are two options, Swing On and Swing Off.

• BLOW: there are two options, Blow on and Blow off.

• E-HEATER: There are two options, E-heater On, E-heater Off.

• TIMER: It is used to set the timer among 0~24h.Within and over 10h, every press of ▲/▼

will increase or decrease timer by 0.5h and 1h respectively.

• AIR: There are two options, Air On and Air Off (reserved).

• SLEEP: There are two options, Sleep On and Sleep Off.

• TURBO: There are two options, Turbo On and Turbo Off.

• SET: There are two options, Set Temperature On and Set Temperature Off.

• TEMP: there are two options,TEMP On and TEMP Off.

• SAVE: It’s used to set temperature limit under cooling and heating mode. Quit “SAVE”

function by pressing “Function” and “▼” simultaneously.

(3) All functions will be shielded by pressing both ▲ and ▼ simultaneously for ve seconds.

After that, “88” LED will display “EE” for ve seconds by pressing any other key to tell the

user that the keypad has been locked. Another press will undo the shielding function and go

to the normal status.

◆Speed

It is available to select the fan speed among auto, low, middle, high circularly by pressing this

key.

2.3.2 Buttons for special functions

(1) Enquiry of the indoor unit address.

Under the “Off” status of the unit, the “88”LED will display the address number of this indoor

unit by pressing the buttons “Speed” and “ON/OFF” simultaneously.

(2) Enquiry of the unit type

Under the “Off” status of the unit, by pressing the buttons “Mode” and “ON/OFF” simultaneously,

for cooling only unit, “COOL” icon will light up on the control panel, while for cooling and heating

unit, “HEAT” icon will light up.

(3) Keypad Lock

Under normal “ON” and “OFF” status, press ▲ and ▼ simultaneously for 5 seconds, the

keypad will be locked., the keypad will be locked, in which case the press on any other key will get

no response. Then, another press on these two buttons will unlock the keypad.

(4) Memory

Under the “Off” status of the unit, it is available to switch the memory mode by pressing “Mode”

and “▲” simultaneously.

When “88” LED displays “ON”, it indicates the memory function is activated; if “OF” is displayed,

it indicates that the memory function is deactivated. When the memory setting page comes out, it

can quit ve seconds later or by pressing the “ON/OFF” key.

(5) Setting of the wired controller

The unit defaults to be controlled by control panel instead of wired controller.

Under the “Off’ status of the unit, by pressing the buttons “Mode’ and “Speed” simultaneously, it

is available to set if the unit can be controlled with or without wired controller..

When “88” LED displays “E6” and the wired control is in normal status, it indicates the unit

is the control of the wired controller rather than the buttons on the control panel and the remote

controller.

When “88” LED is in the normal status and the wired controller displays “E6”, it indicates the

unit is controlled by control panel and the remote controller rather than wired controller.

(6) Setting of the host/slave indoor unit

Under the “Off” status of the unit, it is available to switch the master and slave status of the unit

by pressing the key “Mode” for ve seconds.

When “88” LED displays “HO”, it indicates this indoor unit is set to be master unit.

When “88” LED displays “CH”, it is regarded as the slave unit as it is an invalid host unit.

When “88” LED displays “SL”, it indicates this indoor unit is set to be slave unit.

(7) Enquiry of the unit status, host or slave

Under the “Off” status of the unit, it is available to equity the unit status, host or slave, by

pressing the key ‘Speed”. “HO” indicates it is the host unit, while “CH” or SL” indicate it is the salve

unit.

3 Preparative for Installation

3.1 Standard Accessory Parts

The standard accessory parts listed below are furnished and should be used as required.

No. Name Appearance Q'ty Usage

1 Special Nut 1 To be used for connecting the

refrigerant pipe

2 Wireless Controller 1 To control the indoor unit

3 Wired Controller 1 To control the indoor unit

3.2 Selection of the Installation Location

NOTE !

The unit installation work must be done by qualied personnel according to the local rules and this

manual.

When removing the unit to the other place, please rstly contact with the local maintenance center.

3.2.1 Basic Requirements for Installation Location

Installation at the following places may cause failure of the air conditioner. If inevitable, please

contact installation and service agent.

(1) A place with heat source, steam and inammable gas.

(2) A place with high frequency facility, such as radio equipment, electric welder, or medical

equipments.

(3) A seaside saline-alkali place.

(4) A place full of machine oil.

(5) A place with sulphide gas (such as sulphur spring) .

(6) An environment with special conditions.

3.2.2 Installation Location of Indoor Unit

(1) Select a place avoid the inammable gas produce or leakage.

(2) Select a place avoid the water vapor or oil spayed on the unit.

(3) Ensure that airow can reach every corner of the room.

(4) Choose a place so that the connection pipe could be easily pulled out.

(5) Select the place where the airow f the unit can not be blocked.

(6) Select the position where the few outer air inuenced.

(7) Select the rm and at ground.

(8) Ensure sufcient clearance and space for service and maintenance.

(9) Ensure the installation of indoor unit is in conformity with the requirements of installation

dimension drawing.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Delta Klimaanlage Handbücher

Delta

Delta RowCool HCH1CB0 Bedienungsanleitung

Delta

Delta HEC1000AFR Bedienungsanleitung

Delta

Delta HEC0700BFB Bedienungsanleitung

Delta

Delta INSPIRE Ultra 20 Bedienungsanleitung

Delta

Delta 81HM005J24 Bedienungsanleitung

Delta

Delta HEC2500BFE Bedienungsanleitung

Delta

Delta 86HM050J245 Bedienungsanleitung

Delta

Delta 80CS048J24 Bedienungsanleitung

Delta

Delta HECX1P Series Bedienungsanleitung

Delta

Delta HEC1200PB Bedienungsanleitung

Delta

Delta 9000 BTU Bedienungsanleitung

Delta

Delta PCS100HV Bedienungsanleitung

Delta

Delta HECX1P Series Bedienungsanleitung

Delta

Delta EN PRO ULTRA 13 21WF Series Bedienungsanleitung

Delta

Delta HEC2010FFA Bedienungsanleitung

Delta

Delta HEC1000PB Bedienungsanleitung

Delta

Delta 80CM016J24 Bedienungsanleitung

Delta

Delta HECX1P Series Bedienungsanleitung

Delta

Delta AC-12L-03 Bedienungsanleitung

Delta

Delta 26WC009I24-028DWG Bedienungsanleitung

Delta

Delta 80UT060J24 Bedienungsanleitung

Delta

Delta 21UT024C24 Bedienungsanleitung

Delta

Delta Inspire Ultra Inverter M16 Bedienungsanleitung

Delta

Delta 21CK018C24 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung