Delta AG812 Bedienungsanleitung

INSTRUCTION MANUAL MODEL AG812 ACCESS GATE

♦WARRANTY

♦INSTALLATION

♦OPERATION

CORPORATE HEADQUARTERS

40355 Delta Lane

Palmdale, California 93551

Phone: (661) 575-1100

Fax: (661) 575-1109

Email: [email protected]

EASTERN REGION U.S.A.

125 Wyatt Lane

Fredericksburg, VA 22406

Phone: (540) 310-4050

Fax: (540) 310-4157

Email: [email protected]

WARRANTY AND LIMITATION OF LIABILITY

Delta Scientific Corporation warrants that during the first ninety (90) days from date of shipment,

the Products will be free from defect in material and workmanship. Delta's sole obligation under

this warranty shall be to repair (or at Delta's option, to replace), FOB: Palmdale, California, any

defective product, without charge to Buyer, provided that, (a) Buyer gives Delta written notice of

any such claimed defect within such period of ninety (90) days, (b) the Products, if installed, were

installed by a Delta authorized installer, (c) the Products have not been altered, subjected to

misuse, negligence or accident, or used with parts not authorized by Delta, and (d) the Products

have been maintained in accordance with the instructions provided. NO OTHER WARRANTY IS

EXPRESSED AND NONE SHALL BE IMPLIED, INCLUDING WITHOUT LIMITATION THE

WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR USE OR FOR A

PARTICULAR PURPOSE. THE FOREGOING STATES DELTA'S ENTIRE LIABILITY WITH

RESPECT TO THE PRODUCTS. IN NO EVENT SHALL DELTA BE LIABLE FOR ANY SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH RESULT FROM THE USE BY BUYER

OR ANY OTHER PARTY, OF THE PRODUCTS, AND IN NO EVENT SHALL DELTA'S

LIABILITY EXCEED THE AMOUNTS PAID BY BUYER FOR THE PRODUCTS HEREUNDER.

DISCLAIMER

Please note - careful consideration must be devoted to the selection, placement and design of a

Barricade installation. Just as in the case of any Barricade system, perimeter security device or

security gate that blocks a roadway or drive, care must be taken to ensure that approaching

vehicles as well as pedestrians are fully aware of the Barricades and their operation. Proper

illumination, clearly worded warning signs, auxiliary devices such as semaphore gates, stop-go

signal lights, audible warning devices, speed bumps, flashing lights, beacons, etc. should be

considered. Delta has information available on many such auxiliary safety equipment not

specifically listed herein. It is strongly recommended that an architect and/or a traffic and/or safety

engineer be consulted prior to installation of a Barricade system. Delta will offer all possible

assistance in designing the operating equipment, controls and the overall system, but we are not

qualified, nor do we purport to offer either traffic or safety engineering information.

INTELLECTUAL PROPERTY, DRAWINGS, SPECIFICATIONS AND TECHNICAL DATA

The drawings and/or data included with this equipment unless otherwise noted remain the

confidential property and trade secret of Delta Scientific Corporation. They shall not be disclosed,

reproduced or used for manufacture, design or construction without the express authorization of

Delta Scientific Corporation. The recipient by accepting these drawings and/or data, assumes

custody thereof and under the above terms agrees not to allow the use of by unauthorized

persons.

Table of Contents

Page

GENERAL NOTES: 4

SAFETY INFORMATIO 4

INSTALLATION 4

WIRING 5

LIMIT SWITCH ADJUSTMENT 6

MANUAL GATE ARM OPERATION 6

MANUAL GATE ARM OPERATION (OPTION) 6

DRIVE BELT TENSION 6

SPARE PARTS ORDER DATA 7

DART ARM OPTION 7

HOOK-UP SCHEMATICS

2 Lane, Single Direction, Cash In Or Out 8

2 Lane, Cash Entry, Free Exit 9

1 Lane, Coin Unit/Barrier Gate 10

1 Lane, Free In Or Free Out 11

Entrance & Exit With Revenue Equip. Ticket Dispenser, And Kiosk 12

Typical Ticket Dispenser/Access Gate 13

Card In, Free Out 14

MAINTENANCE 15

TROUBLESHOOTING 15

SPARE PARTS LIST 17

DELTA SCIENTIFIC CORPORATION

MODEL AG812 ACCESS GATE

General

The Delta Scientific Corporation Model AG812 Access Gate is a heavy-duty unit designed to

meet the many needs of restricted traffic control. A large array of control modes are permitted,

including auto/manual operation in conjunction with local or remote pushbutton stations, timers,

radio controls, vehicle loop detectors, infra red detectors, ticket spitters, card readers, coin or

token devices, and computerized electronic tag systems. These devices may be used

independently or in combination. In short, any device which can provide a contact closure may

be used to vend or reset the Gate.

Safety

The Model AG812 Access Gate is equipped with an electric motor driving the gate arm through

a vee-belt/gear box system. Keep hands and fingers away from the unit interior when power is

on. Shut power off before adjusting limit switches or belt tension. Wiring to the terminal strip

should be made by a competent electrician according to the NEC (NFPA 70) and applicable

local codes.

Installation

The Model AG812 is packed in a reinforced cardboard carton with an inner poly bog to guard

against moisture. Do not stack cartons or leave out in the elements until ready to set. Gate

model number and accessories are marked on carton top.

The AG812 is to be located on a solid, non-combustible surface, such as concrete. Mark the

Gate location from the architect’s drawings. Conduit for the Gate motor and controls must be

brought to the stub-up area within the Gate’s bottom opening (shown above). Foundation bolt

location can be marked from the Gate itself or from a template (Delta P/N D03180).

1. Remove cardboard flanges of carton from wooden pallet. Lift carton clear of the AG812

Gate. Do not cut through carton while on the Gate; the knife may score the Gate finish!

2. Insert the key in the lick, unlock and remove cabinet door.

3. Remove bolts holding cabinet to the shipping pallet.

4. Temporarily set Gate where indicated on site plans, transfer mounting hole location to

foundation (or use template). Set Gate aside.

5. Use a masonry drill to provide the holes for the mounting bolts (4 – 3/8” X 4” long). If

appropriate for your application use lag shields (not provided).

6. Relocate the Gate and install the lag bolts using a flat and lock washer on each.

7. Locate gearbox breather vent and remove plug. Vent hole faces upwards when the box

is in operation.

8. Install Gate Arm.

Wiring

As indicated above, the Gate will function using a wide variety of control inputs. Consult the

architectural plans for the required control functions, and then refer to the specific Delta

Scientific Application Guide that covers that function. Common to all hookups:

1. Standard Power input is 120/1/60 VAC for Gate Motor and control power. The AG812

may be ordered from the factory equipped to operate at 240/1/50 also. Conduit should

be run from below grade to the center stub-up area as shown in the installation drawing.

Field wiring connections are terminated at terminals L1 (hot) and L2 (neutral). Other

input voltages are available, and must be selected at time of order. The unit should be

grounded at the provided terminal (green).

2. Gate Auto-Manual: With the Power ‘On’, switching the Auto-Manual switch to ‘Manual’

will vend (raise) the Gate. To reset the Gate, switch Auto-Manual to ‘Reset’ position

momentarily.

3. Heater On-Off –Auto: Gate may be optionally supplied with a 60 watt heater to guard

against condensation on the gate interior surfaces and to provide some heating to

reduce gear box lube oil viscosity in extreme cold. We suggest that the heater switch be

placed in the ‘Auto’ position at all times.

Limit Switch Adjustment

The Limit Switches are preset at the factory for standard operation across a level lane. The limit

switches are adjustable to allow gate arm travel adjustments, where necessary.

CAUTION: Do NOT attempt to adjust the limit switches with the power on. Power switch

must be placed in the ‘Off’ Position before adjustments are made. The directions indicated

below are made when viewing the Gate from the gate arm side, Gate raise direction is

clockwise (CW), Gate lower direction is counter-clockwise (CCW).

1. To adjust the gate arm for more downward travel, loosen the thumb screw on the down

limit switch cam and rotate slightly CW. Tighten screw, turn Power switch ‘On’ and

check by operating the Auto-Manual switch. Turn Gate ‘Off’ and re-adjust as necessary.

2. To adjust the gate arm for less downward travel, loosen the thumbscrew on the down

limit switch cam and rotate slightly CCW. Confirm as above.

3. To adjust the gate arm for more upward travel, loosen the thumbscrew on the up limit

switch cam and rotate slightly CCW, Confirm as above.

4. To adjust the gate arm for less upward travel, loosen the thumbscrew on the up limit

switch cam and rotate slightly CW. Confirm as above.

Manual Gate Arm Operation (Standard Feature):

CAUTION: Do NOT manually operate gate unless power has first been turned off! There

is potential for sever injury if power is restored while manually operating gate.

All AG812 Gates have the capability to be manually raised or lowered. The normal method to

manually raise or lower the gate arm’s position is to:

1. Unlock the access cover.

2. Set the ‘POWER’ Toggle Switch to ‘OFF’.

3. Move the drive belt around by hand, thereby moving the gate arm either up or down as

desired. Use care! Having the hand caught between the pulley and belt is painful!

Manual Gate Arm Operation (Optional):

The AG812 can be ordered with a manual crank to perform manual operation. The Gate’s top

cover is fitted with a plastic plug, which when removed will allow the crank assembly to be used

to rotate the special sheave on the motor shaft.

Drive Belt Tension:

The drive belt requires periodic tension checking. Improper tension of the drive belt can result in

erratic gate arm motion. See Troubleshooting Section.

Spare Parts Order Data:

Parts for your Delta AG812 Gate may be purchased from your installer/dealer or the factory.

Please call your dealer first, as he is most familiar with your application. Required replacement

parts can be located from the attached Spare Parts List.

Try to supply as much data about the part as possible, i.e. dimensional size, threads, voltage,

nameplate data, etc. For control circuits: list model number, serial number (S/N), drawing

number and customer number taken from the nameplate on the controller.

Dart Arm (optional)

The dart arm is an optional, factory-installed device that will cause the AG812 gate arm to

return to the vertical (open) position if the gate arm should encounter a solid object during the

AG812’s ‘close’ (reset) cycle. The dart arm kit includes an arm limit switch, which signals that

the arm has come into contact with an object and also an additional shaft-mounted limit switch,

which must be wired in series with the down limit switch to prevent intentional lifting of the gate

arm and there by causing the arm to rise.

Inhaltsverzeichnis

Andere Delta Automatische Schranke Handbücher

Delta

Delta JA-150IR Bedienungsanleitung

Beliebte Automatische Schranke Handbücher anderer Marken

Cardin

Cardin EL Series Bedienungsanleitung

BFT

BFT Maxima Ultra 36 Bedienungsanleitung

Lip

Lip SLEEK TIME Bedienungsanleitung

AMC

AMC FLEX 500 - 2000 Systemhandbuch

CAME

CAME GARD series Bedienungsanleitung

FAAC

FAAC B680H Bedienungsanleitung

Proteco

Proteco S-Park Series Bedienungsanleitung

Politec

Politec MANA DT SMA Handbuch

King gates

King gates Open 424 Bedienungsanleitung

RIB

RIB RAPID S P1-CRX Bedienungsanleitung

Erreka

Erreka ULTRA Series Betriebsanleitung

BFT

BFT MOOVI 30 Bedienungsanleitung

FAAC

FAAC B 604 Bedienungsanleitung

Alvarado

Alvarado SUPERVISOR 4500 Bedienungsanleitung

PPA

PPA BARRIER BRC Bedienungsanleitung

Parking Facilities

Parking Facilities PF6000X Gebrauchsanweisung

Maxon

Maxon GPC X1-LD Bedienungsanleitung

quiko

quiko QK-CT273800LK4 Stücklistenhandbuch