Delta CP2000 Series Bedienungsanleitung

Delta Fan/Pump Vector

Control Drive

CP2000 Series

Quick Start Guide

www.deltaww.com

Warning! T

his is a short guide, and does not give all necessary safety information.

Refer to the CP2000 Series User Manual for all safety information to avoid

damage to the drive, motor or personal injury.

Document Version 1.0

Published August 25, 2017

Table of Contents

CHAPTER 1 INTRODUCTION .................................................................................................. 3

1-1 Before You Start............................................................................................................... 3

CHAPTER 2 CONTROL WIRING.............................................................................................. 4

2-1 Cabling............................................................................................................................. 4

CHAPTER 3 SET UP THE VFD PARAMETERS....................................................................... 5

3-1 About Parameters ............................................................................................................ 5

3-2 VFD Digital Keypad.......................................................................................................... 5

3-3 Digital Keypad Keys ......................................................................................................... 6

3-4 Display Workflow.............................................................................................................. 7

3-5 Setting Up Parameters for the First Time.......................................................................... 7

Changes to System Parameters (00) group........................................................................ 8

Changes to Basic Parameters (01) group ........................................................................... 9

Digital Input / Output Parameters (02) group......................................................................10

Motor Parameters (05) group.............................................................................................10

Special Parameters (07) group ..........................................................................................11

Communication Parameters (09) group .............................................................................12

CHAPTER 4 START UP TEST.................................................................................................14

APPENDIX A PUBLICATION HISTORY..................................................................................15

Chapter 1 Introduction

This Quick Start Guide shows you how to configure the CP2000 Series drive settings to work

with your Delta Controls controllers. The guide assumes the drive has already been installed on-

site by a qualified technician.

Refer to the CP2000 Series User Manual for more information about how to

unpack (Chapter 3), install (Chapter 2) and wire the drive (Chapter 4 and 5) to its

power supply.

1-1 Before You Start

Verify the following wiring setup before you turn on the VFD for the first time.

•Make sure the line voltage (L1/L2/L3) is not connected to the output terminals (U/V/W) of

the VFD.

•Ensure the motor is connected to the drive before applying power to the VFD.

Chapter 2 Control Wiring

Do not remove the factory jumpers between STO1/STO2/+24V and

SCM1/SCM2/DCM.

Make sure the AFM1 and AVI1 switches are in the 0-10V position.

Make sure the Start Relay shown is not in a closed state when the drive is initially

powered up.

For the conventional start/stop, speed control and speed feedback via hard-wired I/O, the

following wiring terminations are required:

•Start/Stop: Control relay contacts wired between FWD and DCM.

•Speed Control: 0-10V speed control is connected to AVI1 (+) and ACM (-).

•Speed Feedback: 0-10V speed status is connected to AFM (+) and ACM (-).

2-1 Cabling

The analog speed signals should be using shielded cable.

Chapter 3 Set Up the

VFD Parameters

Chapter 3 Set Up the VFD Parameters

This section describes how to set up the VFD parameters when you turn on the drive for the first

time, and how to use the digital keypad on the VFD to access these parameter settings.

3-1 About Parameters

The VFD parameters are organized in groups which are numbered from 00 to 13. Members in

the same group share a common prefix (00 to 13) and each parameter member is identified by

a unique number. The parameters and their settings are accessible on the keypad main menu

by selecting Parameter Setup.

For example, the group Basic Parameters share the prefix “01” and “01-00” is the maximum

operation frequency parameter.

See Chapter 11 and 12 in the VFD-CP2000 User Manual for more details about

the parameters and their factory settings.

3-2 VFD Digital Keypad

The digital keypad consists of keys and a display screen. This section only applies to the KPC

CC01 keypad.

See Chapter 10 in the VFD-CP2000 User Manual for more information.

Chapter 3 Set Up the VFD Parameters | CP2000

3-3 Digital Keypad Keys

Key

Description of Function

RUN

When the VFD is in HAND mode, pressing RUN starts the motor.

STOP/RESET

This key has the highest processing priority in any situation.

Pressing STOP stops the VFD whether the VFD is in HAND mode or

AUTO mode. Once the drive has stopped, pressing STOP/RESET

will clear an outstanding Fault.

FWD/REV

Used to reverse the rotation direction of the motor. Not used in

HVAC applications.

HAND

Pressing HAND puts the VFD into local control mode, where remote

signals are ignored. "HAND" displays on the keypad screen.

While in this mode, it is possible to start the VFD and to manually

control the speed using the keypad.

AUTO

Pressing AUTO puts the VFD into remote control mode, which can

be either hardwired I/O or BACnet control. "AUTO" displays on the

keypad screen. The local RUN and speed control is displayed while

in AUTO.

Press MENU to open or return to the main menu that lists 13

options, including Parameter (Pr) Setup and Display Setup.

ESC

Press ESC to leave the current menu and go back up one level in

the menu. It will also leave any parameter viewed without making

any change to the value.

ENTER

Press ENTER to go to the next level in the menu. It will also apply a

change to a parameter whose value has been altered.

These keys perform two functions, depending on the state of the

display. When in the menu, and scroll through the different

menu levels and parameters. When a single parameter is being

adjusted, and determine which digit of the setting will be

adjusted when you use and . On the display’s main page,

these keys can be used to adjust the running speed of the drive.

F1, F2, F3, F4

These keys are not used by default, but can be customized to

perform application specific functions.

3-4 Display Workflow | CP2000

3-4 Display Workflow

3-5 Setting Up Parameters for the First Time

This section describes how to configure the drive correctly after turning it on for the first time.

To access the VFD parameters on the keypad display,

1. Push the MENU button on the keypad.

2. Scroll through the menu using and to select 1. Pr Setup and press ENTER.

Parameter (Pr) Setup is a menu option that allows you to change the drive’s setup

parameters. The parameters are organized as groups under Parameter Setup, from

System or Drive Parameters (00) to Industry Application Parameters (13).

3. Scroll through the list using and to select the parameter group you want to

modify. Press ENTER to view the parameters in the selected group.

4. Use and to select the parameter you want to modify. Press ENTER to go to the

parameter’s option menu.

5. To select a number that represents the option you want to set, use and .

Chapter 3 Set Up the VFD Parameters | CP2000

To enter a value, use and to increase or decrease the number displayed. In

some cases when you are presented with a string of numbers, decimal places, dates or

times, you may need to use and to move the cursor’s position to make a specific

change.

6. Press ENTER to save the option or changes you’ve made. Use ESC button to go back

up one level in the menu, or push MENU to return to the main menu.

7. Use steps 3 to 6 to make the required changes to the parameters listed below.

The following tables list the parameters that you need to set up and their recommended values.

Changes to System Parameters (00) group

Parameter

Display Text

Description of Parameter

Default

Value

Preferred

Value

00-20 Source of

frequency

Source of

FREQ

The source of frequency

parameter determines which

control signal controls the

drive's frequency in AUTO

mode.

Parameter options:

0 - Keypad (not

recommended)

1 - RS-485 BACnet

2 - Analog Input (used for

hardwired I/O control)

00-21 Source of

operation

Source of

OPER

This determines which

control signal starts or stops

the drive in AUTO mode.

Parameter options:

0 - Keypad (not

recommended)

1 - Hardwired I/O Terminals

2 - RS-485 BACnet

3 - not used

4 - not used

5 - not used

00-22 Stop

method

Stop Methods

This determines what the

drive does when

commanded to stop.

Parameter options:

0 – Ramp to stop

1 – Coast to stop (preferred

for HVAC)

3-5 Setting Up Parameters for the First Time | CP2000

Parameter

Display Text

Description of Parameter

Default

Value

Preferred

Value

00-32 Keypad

stop function

KPD STOP

ENABLE

This determines whether the

STOP key on the keypad is

active when the drive is

running in AUTO mode.

Parameter options:

0 – STOP key disabled.

1 – STOP key enabled

(preferred for safety)

Changes to Basic Parameters (01) group

Parameter

Display Text

Description of Parameter

Default

Value

Preferred

Value

01-11 Output

frequency lower

limit

Lower Bound

FREQ

This determines the

minimum speed of the drive

motor. It is important that

this speed is not too low to

prevent motor overheating.

0.00 Hz

10-15 Hz

01-12

Acceleration time

1st ACC Time

This is the time, in seconds,

for the drive to ramp up from

0 Hz to 60 Hz. It's important

that this time is not too fast,

or an overload fault will trip.

The factory default time is

too low.

10 secs

60 secs

01-13

Deceleration time

1st DEC Time

This is the time, in seconds,

for the drive to ramp down

from 60 Hz to 0 Hz. If this

time is set too low, an OVN

fault will occur. The factory

default time is too low for

large inertia loads like

centrifugal fans.

10 secs

60 secs

Andere Handbücher für CP2000 Series

Inhaltsverzeichnis

Andere Delta Gleichstromantrieb Handbücher

Delta

Delta VFD-B Series Bedienungsanleitung

Delta

Delta VFD-MS300 Series Handbuch

Delta

Delta EB3000 Series Bedienungsanleitung

Delta

Delta CP2000 Series Bedienungsanleitung

Delta

Delta VFD-BW Series Bedienungsanleitung

Delta

Delta C2000 Series Bedienungsanleitung

Delta

Delta C2000 Plus Series Bedienungsanleitung

Delta

Delta CFP2000 Series Bedienungsanleitung

Delta

Delta VFD-B Series Bedienungsanleitung

Delta

Delta CT2000 Series Bedienungsanleitung

Delta

Delta VFD-EL-C Series Bedienungsanleitung

Delta

Delta MS300 Series Bedienungsanleitung

Delta

Delta VFD-E Bedienungsanleitung

Delta

Delta VFD-VL Series Bedienungsanleitung

Delta

Delta PMC-24V150W1AA Bedienungsanleitung

Delta

Delta VFD-M Series Bedienungsanleitung

Delta

Delta VFD-EL-W Series Bedienungsanleitung

Delta

Delta VFD-L-I Series Bedienungsanleitung

Delta

Delta VFD-B Bedienungsanleitung

Delta

Delta VFD-EL-W Series Bedienungsanleitung

Delta

Delta VFD-ME300 Series Handbuch

Delta

Delta VFD-B 230V Series Bedienungsanleitung

Delta

Delta CP2000 Series Bedienungsanleitung

Delta

Delta ME300 Series Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung