Delta TwinLaser 36-255L Bedienungsanleitung

Environmental Health and Safety | 2408 Wanda Daley Drive | Ames, IA 50011-3602 | Ph: (515) 294-5359 | www.ehs.iastate.edu

Reviewed 2019

Delta 12” Compound Miter Saw

Description

Compound Miter Saw – Model 36-255L

Size / Horse power

12” Blade / 5000 RPM

Power source

120 volts through plugged power cord

Uses

Cutting wood and non-ferrous metals

Safety Precautions

Hazards

Severe cuts, potential for amputation

Flying debris (potential eye and face damage)

Electrical shock

Entanglement of hair, jewelry, or clothing

Material kickback

Training

Shop Safety Fundamentals

Site Specific Training

Protective Equipment

Safety Glasses

Hearing Protection

Tie back long hair

Avoid loose fitting clothing

Remove rings, watches, bracelets, and other such jewelry

Operation

Startup

1. Put on PPE listed above

2. Ensure work area is clean and free of obstacles

3. Ensure all guards are present and function properly

4. Make necessary adjustments for safe operation

5. Inspect tool for damage or obstructions to operation

6. Set miter angle by rotating the lock knob counterclockwise and lifting up on

the miter lock lever, rotate saw table to desired angle. Lock miter angle position

by pushing down on the miter lock lever and turning the lock knob clockwise

7. Turn on saw by depressing the power switch (A) located in the handle

8. Slowly bring the blade down to the material being cut, avoid feeding the blade too

quickly

9. Keep hands clear of spinning blade

Shutdown

1. Disengage power switch

2. Return saw to upright position and allow blade to stop rotating. Blade brake should

stop the blade in 5 seconds

3. Remove work piece

4. Lower arm and lock blade in the down position, using the lock down pin

Note: The hole in the trigger is provide for a 3/16” diameter padlock (B) to be inserted

to lock the saw in the OFF position

Environmental Health and Safety | 2408 Wanda Daley Drive | Ames, IA 50011-3602 | Ph: (515) 294-5359 | www.ehs.iastate.edu

Reviewed 2019

Blade Change – Performed by Authorized Personnel Only

1. DISCONNECT MACHINE FROM POWER SOURCE

2. Loosen screw (A) with wrench (B)

3. Rotate arbor cover (C) and lower guard (D) to the rear, exposing arbor screw (E)

4. Remove arbor screw (E) by turning the screw clockwise with the wrench, while at the same time,

pressing in on the arbor lock (F) to keep the arbor from turning. Remove the outside blade flange (G)

and saw blade (H)

5. Install the new saw blade, MAKING CERTAIN THE TEETH OF THE SAW BLADE ARE POINTING

DOWN AT THE FRONT, and install the outside blade flange (G)

6. Check to see that the flats on the outside blade flange are engage with the flats on the arbor shaft

7. Thread the arbor screw (E) into the saw arbor by turning the screw counterclockwise as far as possible

by hand. Then tighten arbor screw with wrench while at the same time pressing in on the arbor lock

8. Rotate arbor cover (C) and lower guard (D) to the front and tighten screw (A)

Tilting Blade for Bevel Cut

1. DISCONNECT MACHINE FROM POWER SOURCE

2. Loosen the bevel lock handle (A)

3. Tilt the cutting head (B) to the desired angle, and tighten the bevel lock

handle (A)

4. Positive stops are provided at 45⁰and 90⁰

5. A marked indicator (M) is provided on the bevel scale for cutting crown

moulding

Adjusting the Sliding Fence

1. Loosen the lock handle (B)

2. Slide the fence to the desired position

3. Tighten lock handle to secure fence

Maintenance

Storage

Care

Only use blades that are 12” in diameter with a 1” arbor hole and are rated for

4000RPM. Use a brush or compressed air to clean the saw

Accessories

•Wrench

•Dust Bag

Andere Handbücher für TwinLaser 36-255L

Inhaltsverzeichnis

Andere Delta Gesehen Handbücher

Delta

Delta RT-31 Bedienungsanleitung

Delta

Delta 36-725 Bedienungsanleitung

Delta

Delta 28-306 Bedienungsanleitung

Delta

Delta 36-412 Bedienungsanleitung

Delta

Delta 20-150 Bedienungsanleitung

Delta

Delta 40-530 Bedienungsanleitung

Delta

Delta 26-2240 Bedienungsanleitung

Delta

Delta RS830 Bedienungsanleitung

Delta

Delta ShopMaster TS300 Bedienungsanleitung

Delta

Delta 430-03-651-0005 Bedienungsanleitung

Delta

Delta 36-075 Bedienungsanleitung

Delta

Delta 36-714 Bedienungsanleitung

Delta

Delta Horizontal Band Saw Benutzerhandbuch

Delta

Delta 36-725 T2 Bedienungsanleitung

Delta

Delta ShopMaster BS100 Bedienungsanleitung

Delta

Delta 36-225 Bedienungsanleitung

Delta

Delta 36-260 Bedienungsanleitung

Delta

Delta 28-190 Bedienungsanleitung

Delta

Delta 36-444 Bedienungsanleitung

Delta

Delta 40-694 Bedienungsanleitung

Delta

Delta ShopMaster MS250 Bedienungsanleitung

Delta

Delta 36-5052 T2 Bedienungsanleitung

Delta

Delta 20-142C Bedienungsanleitung

Delta

Delta 33-891 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung