Delta Agema AG5648 Bedienungsanleitung

Delta Networking – Agema Family

AG5648 Leaf/ToR Switch

Installation Guide

AG5648 Leaf/ToR Switch

All specications and gures are subject to change without prior notice. Actual products may look

different from the photos.

All trademarks and logos mentioned in this guide are the properties of their respective holders.

Regulatory and Safety Information

This product has been tested in accordance to, and complies with the following safety standards and

electromagnetic compatibility (EMC) inspection standards.

Emissions

Applicable standard

• AS/NZS CISPR 22: Class A

• ICES-003, Issue Class A

• EN 55022: Class A

• VCCI Class A

• FCC CFR 47 Part 15, Subpart B Class A

Safety

Applicable standard

• EN 60950-1, Second Edition

• UL/CSA 60950-1, Second Edition

• IEC 60950-1, Second Edition Including All National

Immunity

Applicable standard

• EN 300 386, EMC for Network Equipment

• EN 55024:

• EN 61000-3-2: Harmonic Current Emissions

• EN 61000-3-3: Voltage Fluctuations and Flicker

• EN 61000-4-2: ESD

• EN 61000-4-3: Radiated Immunity

• EN 61000-4-4: EFT

• EN 61000-4-5: Surge

• EN 61000-4-6: Low Frequency Conducted Immunity

• EN61000-4-8: Power Frequency magnetic eld

• EN61000-4-11: Voltage dips and interruptions

RoHS

Applicable standard All AG-Series components are EU RoHS compliant

Warning: Fiber Optic Port Safety

When using a ber optic port, never look at the transmit laser while it is powered

on. Also, never look directly at the ber TX port and ber cable ends when they are

powered on.

iii

Table of Contents

Chapter 1: Introduction -------------------------------------------------------------------1

1.1 Overview ------------------------------------------------------------------------------------ 1

1.2 Package Content -------------------------------------------------------------------------- 1

1.3 Features ------------------------------------------------------------------------------------- 2

Chapter 2: Appearance and Mechanism --------------------------------------------3

2.1 Product Overview ------------------------------------------------------------------------- 3

2.2 LED Identication ------------------------------------------------------------------------- 4

2.3 System Requirements ------------------------------------------------------------------- 6

2.4 Data Center Deployment ---------------------------------------------------------------- 7

2.5 Power Supply Modules ------------------------------------------------------------------ 7

2.6 Fan Tray Module -------------------------------------------------------------------------- 8

Chapter 3: Installation ---------------------------------------------------------------------9

3.1 Mounting ------------------------------------------------------------------------------------ 9

3.2 Installing an Optional Transceiver and Cable -------------------------------------11

3.3 Connecting to the Console Port ------------------------------------------------------12

3.4 Connecting to a Power Source -------------------------------------------------------13

Chapter 4: Making the Network Connections ----------------------------------- 15

4.1 Twisted-pair Connections --------------------------------------------------------------15

4.2 Fiber Optic Connections ---------------------------------------------------------------16

4.3 Ethernet Cabling -------------------------------------------------------------------------17

Appendix 1 : Technical Speciﬁcations--------------------------------------------- 18

Appendix 2 : Warranty------------------------------------------------------------------- 19

Limited and Support Warranty -------------------------------------------------------------19

Technical Support -----------------------------------------------------------------------------19

AG5648 Leaf/ToR Switch

Chapter 1: Introduction

1.1 Overview

The AG5648 is next generation leaf/ToR switch for Data Center Networks, as well as

Enterprise network deployments. It leverage the 100G technology (4x25G Serdes) to provide

48-port 25G SFP28 and 6-port 100G QSFP28 in a compact 1RU form factor with 2.5 times

speed upgrade from current 10Gigabits leaf/ToR switch. The 48 ports 25G are backward

compatible to 10G and the 100G uplink offer dual speed – 40G and 100G.

The AG5648 is also SDN capable and supports ONIE installer and OpenFlow for today’s

open network ecosystem. It also provides comprehensive capability on layer 2 and layer

3 features, including SNMP, Spanning Tree, VLAN, QinQ, Trunk, QoS, RIP, OSPF, IGMP,

DVMRP, PIM-DM, PIM-SM, Access Control, etc. This product which aims for Data Center

Networks also supports advance features such as MPLS, TRILL, PFC, VEPA, QCN, VxLAN

and NVGRE to meet the high-demanding Data Center high performance and virtualization

requirement. The AG5648 is excellent choice for next generation hyper scale and medium

size datacenters and Core/Aggregation switches in Enterprise network environment.

1.2 Package Content

After unpacking this switch, check the contents to be sure you have received all the

components. Then, before beginning the installation, be sure you have all other necessary

installation equipment.

•AG5648 switch

•1 x AC power supply for AC version or 1 x DC power supply for DC version

•Rack-mounting kits

•2 x Velcro strips

•Installation guide

If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.

• IntroductionChapter 1

1.3 Features

The following lists the key main features of the AG5648 switch:

•48 x 25GbE SFP28 ports

•6 x 100GbE QSFP28 ports

•1 x OOB Management

•1 x Console port (RJ-45 type)

•1 x USB port

•Hot plugging redundant power supply support

•4 Fan modules

•System / Fan / Power status LED indication

•On board high performance CPU system with large memory

•Internal power supply; Max power 550W (AC version) or 550W (DC version)

•Standard 1U chassis high

•1.8 Tbps full-duplex switching

•Automatic address learning function to build the packet-forwarding information table. The

table contains up to 288K MAC addresses

•Low pin-to-pin latency: Cut-Through & Store and Forward Mode

•16MB of packet buffer memory

•Support Jumbo Frame up to 12Kbyte

AG5648 Leaf/ToR Switch

Chapter 2: Appearance and Mechanism

2.1 Product Overview

2.1.1 Front View

Management port x 1

RJ-45 Console port x 1

SFP28 port x 48 QSFP28 port x 6

(Figure 2-1: Front View)

2.1.2 Rear View

PSU x 1

4 Fan tray slots

Secondary PSU

slot x 1 (optional)

USB port x 1

Reset x 1

(Figure 2-2: Rear View)

NOTE:

The switch supports up to two PSUs. However, it is shipped with one power supply

pre-installed in the rear panel of the switch. You may purchase an additional PSU for

redundancy.

• Appearance and MechanismChapter 2

2.2 LED Identiﬁcation

This section provides an overview of the front and rear LEDs.

2.2.1 Front LEDs

System LED

Upper SFP28

Port LED

Power LED

Fan Status LED

Lower SFP28

Port LED

Upper QSFP28 Port LED

Lower QSFP28 Port LED

(Figure 2-3: Front LED Identiﬁcation)

LED Description

System LED

• Off – No Power

• Blinking Green – Booting, or System in Diagnostic mode

• Solid Green – Normal operation

• Solid Yellow – Critical Alarm

• Blinking Yellow – Non-critical alarm

Power LED

• Solid Green – Booting

• Off – Power is disconnected

When NOS is running:

• Solid Green – 2 Power Supplies are supplied to the switch and operating

normally

• Solid Yellow – Single power supply is installed and operating

• Blinking Yellow – 2 Power Supplies are installed, but only single power supply

is operating

Fan Status

LED

• Solid Green – FAN is operating normally

• Solid Amber – FAN is failed including incompatible airow direction

25G SFP28

slots

• Off – No link

• Solid Green – A valid link 25G link

• Solid Yellow – A valid link 10G link

• Blinking Green – Packet transmission or reception in progress

AG5648 Leaf/ToR Switch

LED Description

100G QSFP28

slots

LED1

• Off – No link

• Solid Green – A valid 100G link

• Solid Amber – A valid 40G link

• Solid Blue – A valid 10Gbps link

• Solid Purple – A 10Gbps link

LED 2 and 4 (working in breakout)

• Off – 40/100G operation (assuming LED1 is illuminated) or No link

• Solid Blue – A valid 25Gbps link

• Solid Purple – A valid 10Gbps link

Management

port

Link LED

• Off – No link is established on the port

• Solid Yellow – A valid link at 10/100Mbps is established on the port

• Solid Green – A valid link at 1000Mbps is established on the port

Act LED

• Off – No link is established on the port

• Blinking Green – Activity, transmitting or receiving packet at this port

2.2.2 Rear LEDs

Power Supply LED

Fan Tray LED

(Figure 2-4: Rear LED Identiﬁcation)

LED Description

Fan Tray LED

• Solid Green – Fan operating normally

• Solid Red – Fan failed

Power Supply

LED

• Off – No power or power supply failed

• Solid Green – Power is ok

• Appearance and MechanismChapter 2

2.3 System Requirements

Component Requirement

System requirements

Switch fabric capacity Non-blocking full wire speed on all packet sizes

Forwarding architecture Store and forward or cut-through

Port packet forwarding rate

(at 64 Bytes) 14880000 pps (10Gb)

MAC address entries

supported Up to 136K entries

Memory type 16MB buffer memory

OOB port 10/100/1000Mbps, auto sensing, auto negotiation

Host Support • IPv4: 8K min./72K max.

• IPv6: 4K min/36K max.

LPM Route Support • w/o URPF: IPv4 128K, IPv6/64 85K, IPv6/128 21K

• w/ URPF: : IPv4 64K, IPv6/64 21K, IPv6/128 5K

Priority Queues 20 priority queues per port

MAC Address Aging

Support 1,000,000 seconds programable (Default 300 seconds)

Spanning Tree Support

• Support IEEE802.1d STP

• Support IEEE802.1s MSTP

• Support IEEE802.1w RSTP

Host Support 136K shared entries with MAC Table

LPM Routes Support 128K shared entries with MAC Table

Serial Console • Provide visual feedback of the boot process to the user

• Timeout after period of inactivity

Port Trunking • IEEE802.3ad Link Aggregation Protocol (LACP)

• Up to 1024 groups with 256 member per group

Port requirements

Speed Capability per Port

• 10G/25Gbps (SFP28 port)

• 40G/100Gbps (QSFP28 port)

• 10G/25G/40G (QSFP28 port, working in breakout)

Full-Duplex Flow Control Support the IEEE 802.3x PAUSE frame

AG5648 Leaf/ToR Switch

2.4 Data Center Deployment

The following gure illustrates the converaged Ethernet data center deployment.

Spine

Leaf

6x100G uplink

25G downlink via

Breakout cable

AG5648

25G downlink

AG5648

25G downlink

AG5648

25G downlink

AG9032 v1 AG9032 v1 AG9032 v1 AG9032 v1

AG9032 v1

(Figure 2-5: Converaged Ethernet Data Center Deployment)

2.5 Power Supply Modules

The power supply modules are hot-swappable power supply units (PSUs) for the switch.

You can install up to two PSUs. The PSUs operate in a load-sharing mode and provides 1+1

redundancy.

(Figure 2-6: Power Supply Unit)

NOTE:

1+1 redundancy is a system where a switch power supply is backed up by

another switch power supply in a load-sharing mode. If one power supply fails,

the other power supply takes over the full load of the switch.

WARNING:

• The switch includes plug-in power supply and fan tray modules that are

installed into its chassis. All modules have a front-to-back airow direction.

• Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.

• Remove the power cable from the module prior to removing the module

itself. Power cable must not be connected prior to insertion in the chassis or

equivalent.

Inhaltsverzeichnis

Andere Delta Schalten Handbücher

Delta

Delta AG9032 Bedienungsanleitung

Delta

Delta AG7648 Bedienungsanleitung

Delta

Delta AG9064 Bedienungsanleitung

Delta

Delta DVS-G008W01 Bedienungsanleitung

Delta

Delta HYPERSPROUT Bedienungsanleitung

Delta

Delta STS30002SR00035 Bedienungsanleitung

Delta

Delta DVS Series Bedienungsanleitung

Delta

Delta Agema Series Bedienungsanleitung

Delta

Delta AGC7648A Bedienungsanleitung

Delta

Delta DS-7604NI-K1/4P Bedienungsanleitung

Delta

Delta DVS-103I02C-DLR Bedienungsanleitung

Delta

Delta MST-01 Bedienungsanleitung

Delta

Delta IPB-5-10A-S4 Bedienungsanleitung

Delta

Delta EXPERT-POE-54G Bedienungsanleitung

Delta

Delta DVS Series Bedienungsanleitung

Delta

Delta OR-CR-213 Bedienungsanleitung

Delta

Delta InfraSuite STS 16A Bedienungsanleitung

Delta

Delta NovoConnect B360 Bedienungsanleitung

Delta

Delta AG6248C Bedienungsanleitung

Delta

Delta LE-764501 Bedienungsanleitung

Delta

Delta PFS3106 Bedienungsanleitung

Delta

Delta Agema Series Bedienungsanleitung

Delta

Delta EXPERT-POE-1616 Bedienungsanleitung

Delta

Delta TL-SG1024D Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch