DEMA 167 Bedienungsanleitung

DEMA PROPORTIONER

MODEL 167 & 167T

INSTALLATION INSTRUCTIONS

I-107 Pg. 1 of 5

Rev. B-40495 3/2/15

1. PARTS

A. Proportioner Assembly.

B. Supply tubing with foot valve & ceramic weight.

2. INSTALLATION

This product is designed only to be used as described in this instruction sheet. Adhere to all warnings and

cautions identified in this document.



WARNING: Installations must conform to all local and national plumbing codes and use

approved backflow prevention and pressure relief devices where required.

ALWAYS DISCONNECT DISPENSER FROM WATER SOURCE WHEN DISPENSER

IS NOT IN USE.



Always read SDS for all chemicals used and follow personal protective guidelines.

Screw proportioner directly onto standard external aerator threads. Remove inlet adapter for mounting on garden hose threads. For

other faucets see reverse side for adapter part numbers. For cities with plumbing codes requiring back siphonage protection, install

Dema part 34-22 between faucet and proportioner. See Fig. 1 for supply tubing attachment. Cut vinyl tubing to any convenient length,

slip on the ceramic weight, and push the open end over the detergent inlet barb. Soften end of tubing in hot water to facilitate

attachment. See Section 4 for adjustment screw setting guide. For filling buckets or mop rigs: a short lengthof open ended garden hose

may be attached to the proportioner outlet. Replace screen retainer part 100-8 with hose adapter part 100-10. Use one screen part 100-7

to insure priming.

3. OPERATION

Turn on water and push red button to draw in chemical. Push green button for clear water.

4. PROPORTIONER ADJUSTMENT

WARNING: USE CARE WHEN HANDLING HAZARDOUS CHEMICALS.

DEMA PROPORTIONER

MODEL 167 & 167T

INSTALLATION INSTRUCTIONS

I-107 Pg. 2 of 5

Rev. B-40495 3/2/15

Table 1, 167 Proportioner (Metering Screw)

MODEL 167T:

The injection rate of the detergent or disinfectant into the water is controlled by screwing a color coded metering tip selected from Table

2 into the chemical inlet barb.

MODEL 167:

The injection rate of the detergent or disinfectant into the water can be adjusted by turning the recessed screw in the left side of the

proportioner. The injection rates for various settings and for products of different viscosities are as shown in Table 1.

Turns Counterclockwise from

Closed Position

Injection rate for viscosities shown

1 cps 75 cps 200 cps

Oz/Gal Oz/Gal Oz/Gal

1 0.40 ------ ------

2 3.25 1.75 0.90

2 5.75 2.50 1.00

3 8.25 2.75 1.05

4 12.85 3.00 1.10

Metering

Tip

Color

Injection rates for viscosities shown

1 cps 75 cps 200 cps

Oz/Gal Ratio Oz/Gal Ratio Oz/Gal

Ratio

Tan 0.25 512-1 0.17 756-1 0.15 853-1

Orange 0.35 366-1 0.25 512-1 0.20

640-1

Turquoise 0.50 256-1 0.33 384-1 0.25 512-1

Pink 0.63 205-1 0.45 284-1 0.33

384-1

Clear 0.75 171-1 0.66 213-1 0.45 284-1

Brown 1.00 128-1 0.70 183-1 0.50

256-1

Red 1.25 102-1 0.80 160-1 0.60 213-1

White 1.50 85-1 1.00 128-1 0.70

183-1

Green 1.75 73-1 1.15 111-1 0.75 171-1

Blue 2.00 64-1 1.35 95-1 0.85

150-1

Yellow 3.20 40-1 1.85 69-1 0.95 135-1

Black 4.00 32-1 2.20 58-1 1.00

128-1

Purple 6.40 20-1 2.50 51-1 1.05 122-1

Gray 10.00 12-1 2.75 47-1 1.07

120-1

No Tip 12.00 10-1 3.20 40-1 1.10 116-1

DEMA PROPORTIONER

MODEL 167 & 167T

INSTALLATION INSTRUCTIONS

I-107 Pg. 3 of 5

Rev. B-40495 3/2/15

5. SERVICING

CAUTION: Turn off water supply before servicing.

A. Failure to inject chemical

a. Low water pressure. At least 10 psi is required.

b. Dirt or chemical on outlet screens. Clean.

c. Detergent passage blocked. Back off adjusting screw. Remove proportioner and soak in hot water to clean internal

passages.

d. Foot valve clogged. Soak in hot water.

e. Lime deposits in water passages. Remove proportioner and soak in a deliming solution.

f. Outlet hose (if used) obstructed or too long.

B. Injection in "clear" slide position.

a. Slide valve of vacuum breaking air vent clogged with grease or dirt. Remove proportioner and soak in hot water.

b. Chemical container above level of faucet. Place container on floor.

CAUTION: When servicing unit, be sure that replacement parts have been installed according to drawing.

DEMA PROPORTIONER

MODEL 167 & 167T

INSTALLATION INSTRUCTIONS

I-107 Pg. 4 of 5

Rev. B-40495 3/2/15

CLEAR VINYL

FOOT VALVE

CERAMIC WEIGHT

SUPPLY TUBING FIGURE 1

ADJUSTMENT SCREW MOD. 167

METERING TIP MOD. 167T

CHEMICAL

INLET BARB

RED PUSH BUTTON

OUTLET SCREEN RETAINER

AIR VENT

FAUCET

INLET ADAPTER

RETURNS: NO MERCHANDISE MAY BE RETURNED FOR CREDIT WITHOUT DEMA’S WRITTEN PERMISSION.

RETURN MERCHANDISE AUTHORIZATION NUMBER REQUIRED IN ADVANCE OF RETURN.

WARRANTY: DEMA products are warranted against defective material and workmanship under normal use and service for one

year from the date of manufacture. This limited warranty does not apply to any products which have a normal life

shorter than one year or failure and damage caused by chemicals, corrosion, improper voltage supply, physical

abuse, or misapplication. Rubber and synthetic rubber parts such as “o”- rings, diaphragms, squeeze tubing and

gaskets are considered expendable and are not covered under warranty. This warranty is extended only to the

original buyer of DEMA products. If products are altered or repaired without prior approval of DEMA, this

warranty will be void.

Defective units or parts should be returned to the factory with transportation prepaid. If inspection shows them to

be defective, they will be repaired or replaced without charge, F.O.B. factory. DEMA assumes no liability for

damages. Return merchandise authorization number, to return units for repair or replacement, must be granted in

advance of return.

DEMA PROPORTIONER

MODEL 167 & 167T

INSTALLATION INSTRUCTIONS

I-107 Pg. 5 of 5

Rev. B-40495 3/2/15

NO. PART NO. DESCRIPTION

1 100-3 Inlet Washer (2-Reqd.)

2 100-7 Priming Screens (1 To 3 Needed)

3 100-8 Screen Retainer

4 100-10 Adapter

5 100-24 Metering Screw

6 100-15 Metering Tip

7 150-6 Adapter Washer

8 100-12 7/32” ID x 3/8”OD x 8’ Lg.

Supply Tubing

9 61-107-2 Ceramic Weight (1/4” ID x 3/8”

OD Tubing)

10 100-16E Foot Valve

ACCESSORIES

NO. PART NO. DESCRIPTION

11 150-23 Outside Chicago Thread Adapter

12 150-21 Inside Aerator Thread Adapter

13 150-32 Inside Kohler Thread Adapter

14 150-9-2 Irregular Faucet Adapter

15 34-22 Backflow Preventer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DEMA Steuereinheit Handbücher

DEMA

DEMA 151 Bedienungsanleitung

DEMA

DEMA CHEMASTER DM-813-LLL-1T Bedienungsanleitung

DEMA

DEMA Chemaster DM-813-PLLL-1T Bedienungsanleitung

DEMA

DEMA 440 Bedienungsanleitung

DEMA

DEMA TITAN II T-812-LL Bedienungsanleitung

DEMA

DEMA 463PS Bedienungsanleitung

DEMA

DEMA 154 Bedienungsanleitung

DEMA

DEMA 481-2 Bedienungsanleitung

DEMA

DEMA 434N Bedienungsanleitung

DEMA

DEMA 401P Bedienungsanleitung

DEMA

DEMA 466PV Bedienungsanleitung

DEMA

DEMA 153 Bedienungsanleitung

DEMA

DEMA 294DC Bedienungsanleitung

DEMA

DEMA 466P Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung