Demerbox DB1 Bedienungsanleitung
Ultimate outdoor bluetooth®speaker
DB1
QUICKSTARt guide
Using In and Around Water or Sand
IMPORTANT: Your DemerBox is only waterproof and sealed when the port plug is
properly inserted!
To Insert the Port Plug
1. Unscrew the port plug from its holder inside the DB1. To do this, use
one hand to hold the port plug collar while using your other hand to turn
the wings.
2. Close the DB1 lid and latch it.
3. Insert the port plug into the port tube outside the DB1 until the
port plug is fully seated in the port hole. To do this, use one
hand to hold the port plug collar and turn the port plug wings
clockwise until the plug is secure in the port hole. A snug
t is all you need.
Single Unit Mode
Turn on the DemerBox DB1 by pressing the Power
button . Find DemerBox DB1 under your device’s
Bluetooth®settings and select it.
Charging a Device Using the DB1
1. Plug a device into the USB charge out port on
the DB1.
2. Turn on the DemerBox DB1. Keep in mind, a DB1
battery will drain faster if you’re charging a device
from it.
Aux Cable
Plug one end of the AUX cable into the DemerBox DB1
and the other into the audio output of your device.
Volume Controls
You can control the volume two ways:
1. Use the volume controls on your device.
2. Use the UP/DOWN arrow buttons on
the front of the DemerBox. These only work in
Bluetooth mode.
CHARGING
First time use
Charge the DemerBox DB1 fully before using for the rst time.
The light on the charger will turn from red to green when fully charged.
Charge Status
The ve green LED lights on the DemerBox DB1 control panel show
the battery state of charge. When all ve LEDs are lit up, it will have
approximately 40 hours of continuous play time.
Preserving Battery Life
For best long-term battery life, don’t leave the DemerBox DB1 plugged
in for extended periods after the battery is charged.
Using the DemerBox
CHARGE
DEMERBOX
CHARGE
STUFF
AUDIO
IN
Demerbox.com
MULTI-cast Mode:
Connecting Multiple Speakers Together
Enable Multi-cast Mode for Speakers
1. Choose a speaker and connect to it via Bluetooth. (This will be the ‘Primary’ speaker.)
2. Next, press and hold the UP button until you hear “broadcast mode enabled”. The right LED light on the
keypad will begin to blink.
3. Turn ON another DB1 or DB2 speaker. (This speaker will be a ‘Satellite’ speaker.)
4. On the second speaker, press and hold the DOWN button until you hear “broadcast audio enabled”.
Both speakers are now ENABLED for multi-cast mode, and ready for pairing.
5. To activate multi-cast pairing, quick press both the UP and DOWN volume buttons on the Primary
speaker at the same time. Repeat this action on the Satellite speaker.
a. The Primary DemerBox LEDs will start a back and forth tracking pattern.
b. The Satellite DemerBox LEDs will alternate in a LEFT / RIGHT pattern.
c. After a few seconds you should hear “paired.” You are now ready to listen to both speakers.
Exiting Multi-cast Mode
To exit multi-cast mode, hold down the UP/DOWN volume buttons for 5 seconds. You can also turn the
speaker OFF/ON .
Volume Control
When in multi-cast mode, the Primary speaker volume buttons control the volume on all paired speakers. You can
also use the volume control on your device.
Add an additional speaker
Once the boxes are in multi-cast pairing mode, they will stay active for 30 seconds. You maybe able to connect
several more speakers to the Primary during this time. (You will know if the speakers are active if they display the
LED patterns described in 5a, 5b above).
If you are adding another speaker more than 30 seconds after initial Primary and Satellite pairing,
repeat steps 3-5c.
@DEMERBOX
Inhaltsverzeichnis
Andere Demerbox Sprecher Handbücher
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung