Denali CANsmart DNL.WHS.13400 Bedienungsanleitung

Instruction Rev00

0mm 10 20 30 40 50 60 70 80 90

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra

mile to make sure our instructions are clear and as easy to understand as possible. If

you have any questions, comments, or suggestions don’t hesitate to give our experts

a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing

DENALI products should always be installed by a qualified motorcycle technician. If

you are unsure of your ability to properly install a product, please have the product

installed by your local motorcycle dealer. DENALI takes no responsibility for damages

caused by improper installation. Caution: When installing electronics it is extremely

important to pay close attention to how wires are routed, especially when mounting

products to the front fender, front fork, or fairing of your motorcycle. Always be sure

to turn the handlebars fully left, fully right, and fully compress the suspension to

ensure the wires will not bind and have enough slack for your motorcycle to operate

properly.

Installation Tips

We strongly recommend using medium strength liquid thread locker on all screws and

bolts. It is also important to ensure that all hardware is tightened to the proper torque

specifications as listed in your owner’s manual. For included accessory hardware

please refer to the default torque specifications provided below. Inspect all hardware

after the first 30 miles to ensure that proper torque specifications are maintained.

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.

Remember, the length of a screw or bolt is measured from the start of the “mounting

surface” to the end of the screw, so only include the screw head when measuring

countersunk screws.

M3 10.0 in-lbs - 1.0 Nm

M4 23.0 in-lbs - 2.5 Nm

M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm

M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm

M8 - 13.5 ft-lbs 18.0 Nm

M10 - 30.0 ft-lbs 41.0 Nm

M12 - 52.0 ft-lbs 71.0 Nm

in-lbs

ft-lbs NmBolt Size

0in 1 2 3

What’s In The Box?

DENALIELECTRONICS.COM

Instruction Manual

(a) CANsmart Wiring Harness for T3 Switchback Signals.................Qty 1

Kit Contents

CANsmart Wiring Harness

for

T3 Switchback Signals

DNL.WHS.13400

1. Harness Overview

1.1 - Overview of Harness

DENALIELECTRONICS.COM

2.1 - CANsmart Connections

Follow the steps in this section to configure the harness for installation of a

set of four T3 lights; two rear T3 pods & two front T3 pods. If configuring for

an installation of just front or rear T3 pods follow the steps listed in Section 5.

Step One: Connect the longest lead of harness to the White circuit of the

CANsmart.

Step Two: Connect the second longest lead of the harness to the Yellow

circuit of the CANsmart.

Step Three: Connect the third longest lead of the harness to the Blue circuit

of the CANsmart.

Step Four: Connect the shortest lead of the harness to the Red circuit of

the CANsmart.

The DENALI CANsmart™ Wiring Harness for T3 Switchback Signals provides

plug-n-play installation of four T3 Pods to the CANsmart™ Controller.

Compatible with all GEN II DENALI CANsmart™ Controllers, no wire tapping or

other modifications are necessary, just plug directly into the circuits of the

CANsmart to send the signals from your controller to the T3 Lights. This

harness is designed to power a set of four T3 lights; two rear T3 pods & two

front T3 pods, but can also be configured for an installation of just front or rear

T3 pods as well.

Rear Right T3 Front Right T3

Front Left T3

Rear Left T3

Front T3 Extension

CANsmart Red Circuit

CANsmart Blue Circuit

CANsmart Yellow Circuit

CANsmart White Circuit

2. Connecting To CANsmart Controller

3. Conﬁguring CANsmart Controller DENALIELECTRONICS.COM

3.1 - Configure CANsmart Using Software

The CANsmart Accessory Manager will be used to configure your controller

for operation of the T3 signals, for further details of how to use the

software refer to the manual that was provided with your CANsmart

Controller.

Step One: Use the Circuit Function Selector to configure each of the four

circuits as shown above.

(Red Circuit=Left Turn, Blue Circuit=Brake Light, Yellow

Circuit=Light Pair 1, White Circuit=Right Turn)

Step Two: In the Auxiliary Lights One panel, disable “Three-Wire dimming

Mode”.

Step Three: In the Turn Signal panel, set the running light intensity to 0%.

The remainder of the settings can be configured as desired, but it is important

the settings made in steps one through three are not changed or the lights will

not function properly.

Note: If installing just front T3 pods, you do not need to set the Blue Circuit to

Brake Light. Likewise, if installing just rear T3 pods, you do not need to set the

Yellow Circuit to Light Pair One. The unused circuit can be configured to any

circuit function to power another accessory.

5. Alternate Wiring Options

4. Wiring The Lights DENALIELECTRONICS.COM

5.1 - Wiring For Rear T3 Pods Only

4.1 - Routing The Harness

Once the connections to the CANsmart Controller have been made and the

software has been configured you will need to identify the left side and

right side T3 lights.

Step One: If installing front T3 pods, connect the Front T3 Extension to

the long lead of the harness and begin routing the harness towards the

mounted front pods, then connect the pods to the end of the extension.

Step Two: If installing rear T3 pods, begin routing the lead from the rear

pods towards the harness and then connect the pods to the two short leads

of harness.

Step Three: With the motorcycle’s ignition on, activate each side turn signal

and make sure the T3 pods are flashing on the correct side of the vehicle. If

incorrect, simply swap the connections or remount the pods on the other side

of the vehicle.

If configuring for an installation of just rear T3 pods follow the steps listed

below.

Step One: Connect the longest lead of the harness to the White circuit of the

CANsmart.

Step Two: Connect the third longest lead of the harness to the Blue circuit of

the CANsmart.

Step Three: Connect the shortest lead of the harness to the Red circuit of

the CANsmart.

Note: The unused Yellow Circuit can be used to control an additional device

of your choosing.

Front Right T3

Front Left T3

CANsmart

Rear Left T3

Rear Right T3

Front T3 Extension

Harness

5.3 - Tapping Factory Turn Signals

DENALIELECTRONICS.COM

5. Alternate Wiring Options (Continued)

If you already have other devices on your CANsmart and only have two circuits

available, you can use the motorcycle’s factory turn signal wires for the turn signal

input.

Step One: Remove the connector from the longest lead of the harness and then

use a posi-tap connector to tap the factory left side turn signal positive wire.

Step Two: Connect the third longest lead of the harness to the Yellow circuit of

the CANsmart.

Step Three: Connect the second shortest lead of the harness to the Blue

circuit of the CANsmart.

5.2 - Wiring For Front T3 Pods Only

If configuring for an installation of just front T3 pods, follow the steps listed

below.

Step One: Connect the longest lead of the harness to the White circuit of the

CANsmart.

Step Two: Connect the second longest lead of the harness to the Yellow

circuit of the CANsmart.

Step Four: Connect the shortest lead of the harness to the Red circuit of

the CANsmart.

Step Four: Remove the connector from the shortest lead of the harness and

then use a posi-tap connector to tap the factory right side turn signal positive

wire.

Note: The unused Blue Circuit can be used to control an additional device of

your choosing.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Denali Kabel und Steckverbinder Handbücher

Denali

Denali DialDim DNL.WHS.20500 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung