Denon AVR 4308CI - AV Network Receiver Bedienungsanleitung

- 1 -

DENON AVR control protocol

Ver. 5.1.0_a

Application model : AVR-4308

Application terminal: RS-232C/ Ethernet

Connector specification

Ⅰ. RS-232C

Connector type: DB-9pin female type, slave straight connection (DCE type)

( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )

Communication format:

Synchronous system : Tone step synchronization

Communication system : A half duplex

Communication speed : 9600bps

Character length : 8 bits

Parity control : None

Start bit : 1 bit

Stop bit : 1 bit

Communication procedure : Non procedural

Communication data length : 135 bytes (maximum)

Version Date Contents Page

5.1.0 06.Jul.’07 Original

5.1.0_a 23.Jan.’08 1.Added NSE,NSB,NSC for iRadio Control. 24,42

2.Corrected the Command of IPE,IPA for iPod Control. 25,43,44,45,46

3.Added Response MS Command for DTS Mode. 31,32

4.Corrected the Response Command of PSMODE. 33

- 2 -

Ⅱ. Ethernet

Connector type ：RJ-45(10BASE-T/100BASE-TX)

Communication format ：

Communication system : A half duplex

Communication speed : 10Mbps/100Mbps

Communication port : TCP port 23 (telnet)

Communication data length : 135bytes (maximum)

AVR/AVC

Ethernet

Cross cable

AVR/AVC

HUB

Ethernet

Straight

cable

Ethernet

Straight

cable

Example ①

Example ②

- 3 -

NETWORK SETUP of AVR-4308

>Procedure of Network Setup mode.

(1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI)

(2)Select “Network Setup > Detail” .

(3)Set parameters described below.

<DHCP> "ON"---Use this setting when DHCP server is on the local network.

"OFF"---Use this setting when DHCP server is not on the local network.

<IP Address> When <DHCP> sets "OFF”, please set IP address.

When <DHCP> sets "ON”, you can confirm the IP address that is set by server.

<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.

When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.

<Gateway> Set the address of Gateway when Gateway is on the local network.

Do not set this parameter when Gateway is not on the local network.

<Primary DNS> Do not set this parameter.

<Second DNS> Do not set this parameter.

<Proxy> Set this parameter "OFF".

(1)Press MENU button, then Menu appears on FL-display (and GUI)

(2)Select “Manual Setup > Network Setup > Other > Power Saving”

(3)Set parameters described below.

“OFF”---Use this setting when using the AVR-4308 connected in a network.

“ON”--- Use this setting when not using the AVR-4308 connected in a network.

This setting is reducing the power consumption in the standby mode.

- 4 -

Protocol specification

The following three data forms are defined.

COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.)

A command to a system is given from a controller.

EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR)

The result is sent, when a system is operated directly and a state changes.

*The form of EVENT presupposes that it is the same as that of COMMAND.

**Refer to the following table for the contents of COMMAND and EVENT.

RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR)

if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.

The RESPONSE should be sent within 200ms of receiving the COMMAND.

*The form of RESPONSE presupposes that it is the same as that of EVENT.

Basic specification: The command by ASCII CODE, parameter expression

*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs,

AND carriage return (0x0D) --- It is used only as a pause sign.

Command structure: COMMAND + PARAMETER + CR (0x0D)

COMMAND: ASCII CODE of 2 characters

Ex. SI : Select Input source

MS : surround Mode Setting

MV : Master Volume setting

PW : system Power setting

PARAMETER : ASCII CODE ( up to 25 characters)

ex. DVD : function name

SUPER STADIUM : surround mode name

*Special Parameter--- ? : for request command

- 5 -

The example of a command * <CR> is the meaning of 0x0D.

SIDVD<CR> : Select Input source DVD

MSSTEREO<CR> : surround Mode Set to STEREO

MVUP<CR> : Master Volume UP

PWON<CR> : system PoWer ON

PWSTANDBY<CR> : system PoWer STANDBY

SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’

- 6 -

Others

A) COMMAND is receivable also during transmission of EVENT.

B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels

returns as EVENT.

C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,

the data of an intact channel is set to "50".

D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel

volume of all channels , It described in B) ) returns as EVENT.

E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME

does NOT return.

F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.

G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.

H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to

the another request commands(ex. SV command).

I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.

J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three

ASCII characters as bellows.

Ex. MASTER VOLUME = +1.0dB : MV81<CR>

+0.5dB : MV805<CR>

0dB : MV80<CR>

-0.5dB : MV795<CR>

-1.0dB : MV79<CR>

| |

-79.5dB : MV005<CR>

-80.0dB : MV00<CR>

--- : MV99<CR>

* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.

K) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）.

- 7 -

COMMAND and PARAMETER list

COMMAND PARAMETER function example

PW ON POWER ON/STANDBY change PWON<CR>

STANDBY PWSTANDBY<CR>

? Return PW Status PW?<CR>

MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR>

DOWN MVDOWN<CR>

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR>

? Return MV Status MV?<CR>

CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR>

FL DOWN ---FRONT Lch CVFL DOWN<CR>

FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR>

FR UP CVFR UP<CR>

FR DOWN ---FRONT Rch CVFR DOWN<CR>

FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR>

C UP CVC UP<CR>

C DOWN ---CENTERch CVC DOWN<CR>

C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR>

SW UP CVSW UP<CR>

SW DOWN ---SUBWOOFERch CVSW DOWN<CR>

SW ** **:00,38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50<CR>

SL UP CVSL UP<CR>

SL DOWN ---SURROUND Lch CVSL DOWN<CR>

SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50<CR>

SR UP CVSR UP<CR>

SR DOWN ---SURROUND Rch CVSR DOWN<CR>

SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50<CR>

SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR>

SBL DOWN CVSBL DOWN<CR>

SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>

SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR>

SBR DOWN CVSBR DOWN<CR>

SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR>

MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

- 8 -

COMMAND PARAMETER function example

CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR>

SB DOWN CVSB DOWN<CR>

SB ** **:00 to 99 by ASCII , 50=0dB CVSB 50<CR>

? Return CV Status CV?<CR>

MU ON OUTPUT MUTE ON/OFF change MUON<CR>

OFF MUOFF<CR>

? Return MU Status MU?<CR>

SI PHONO Select INPUT source SIPHONO<CR>

CD SICD<CR>

TUNER SITUNER<CR>

DVD SIDVD<CR>

HDP SIHDP<CR>

TV/CBL SITV/CBL<CR>

SAT SISAT<CR>

VCR SIVCR<CR>

DVR SIDVR<CR>

V.AUX SIV.AUX<CR>

NET/USB SINET/USB<CR>

XM (North America model Only) SIXM<CR>

HDRADIO (North America model Only) SIHDRADIO<CR>

DAB (Europe model Only) SIDAB<CR>

IPOD SIIPOD<CR>

? Return SI Status SI?<CR>

ZM ON MAIN-ZONE ON/OFF change at AVR-4308 ZMON<CR>

OFF ZMOFF<CR>

? Return ZM Status ZM?<CR>

SR PHONO REC SELECT mode set , and select source SRPHONO<CR>

| ---The name of PARAMETER is |

IPOD the same as that of the time of SI COMMAND. SRIPOD<CR>

SOURCE REC SELECT mode cancel SRSOURCE<CR>

? Return SR Status SR?<CR>

CV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)

- 9 -

COMMAND PARAMETER function example

SD AUTO set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR>

HDMI set force HDMI INPUT mode SDHDMI<CR>

DIGITAL set force DIGITAL INPUT (Optical,Coaxial)mode SDDIGITAL<CR>

ANALOG set force ANALOG INPUT mode SDANALOG<CR>

EXT.IN-1 ---Set EXT.IN mode at AVR-4308 SDEXT.IN-1<CR>

? Return SD Status SD?<CR>

DC AUTO set DIGITAL INPUT AUTO mode DCAUTO<CR>

PCM set DIGITAL INPUT force PCM mode DCPCM<CR>

DTS set DIGITAL INPUT force DTS mode DCDTS<CR>

? Return DC Status DC?

SV DVD VIDEO SELECT mode set , and select source SVDVD<CR>

HDP SVVDP<CR>

TV/CBL SVTV/CBL<CR>

SAT SVSAT<CR>

VCR SVVCR<CR>

DVR SVDVR<CR>

V.AUX SVV.AUX<CR>

SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>

? Return SV Status SV?<CR>

MS DIRECT Select SURROUND mode MSDIRECT<CR>

PURE DIRECT MSPURE DIRECT<CR>

STEREO MSSTEREO<CR>

STANDARD MS STANDARD<CR>

DOLBY DIGITAL MSDOLBY DIGITAL<CR>

DTS SUROUND MSDTS SURROUND<CR>

NEURAL MS NEURAL<CR>

North America model only

WIDE SCREEN MSWIDE SCREEN

7CH STEREO MS7CH STEREO<CR>

SUPER STADIUM MSSUPER STADIUM<CR>

ROCK ARENA MSROCK ARENA<CR>

JAZZ CLUB MSJAZZ CLUB<CR>

- 10 -

COMMAND PARAMETER function

example

MS CLASSIC CONCERT MSCLASSIC CONCERT<CR>

MONO MOVIE MSMONO MOVIE<CR>

MATRIX MSMATRIX<CR>

VIDEO GAME MSVIDEO GAME<CR>

VIRTUAL MSVIRTUAL<CR>

? Return MS Status MS?<CR>

QUICK1 QUICK SELECT 1-3 MODE SELECT MSQUICK1<CR>

QUICK2 MSQUICK2<CR>

QUICK3 MSQUICK3<CR>

QUICK1 MEMORY USER1-3 MODE MEMORY MSQUICK1 MEMORY<CR>

QUICK2 MEMORY MSQUICK2 MEMORY<CR>

QUICK3 MEMORY MSQUICK3 MEMORY<CR>

QUICK ? Return MSQUICK Status MSQUICK ?<CR>

VS MONIAUTO

Set HDMI MONITOR automatic detection VSMONIAUTO<CR>

MONI1 Set HDMI MONITOR OUT-1 VSMONI1<CR>

MONI2 Set HDMI MONITOR OUT-2 VSMONI2<CR>

MONI? Return VSMONITOR Status VSMONI?<CR>

ASPNRM

Set Normal mode VSASPNRM<CR>

ASPFUL

Set FULL mode VSASPFUL<CR>

ASP? Return VSASPECT Status VSASP?<CR>

SC48P Set Resolution to 480p/576p VSSC48P<CR>

SC10I Set Resolution to 1080i VSSC10I<CR>

SC72P Set Resolution to 720p VSSC72P<CR>

SC10P Set Resolution to 1080p VSSC10P<CR>

SC AUTO Set Resolution to AUTO VSSCAUTO<CR>

SC? Return VSSCALE Status VSSC?<CR>

Andere Handbücher für AVR 4308CI - AV Network Receiver

Dieses Handbuch passt für folgende Modelle

Andere Denon Stereo-Receiver Handbücher

Denon

Denon AVR-X510BT Bedienungsanleitung

Denon

Denon AVR-787 Bedienungsanleitung

Denon

Denon AVR-X4500H Bedienungsanleitung

Denon

Denon AVR-1404 Bedienungsanleitung

Denon

Denon AVR-X6700H Bedienungsanleitung

Denon

Denon AVR-2312 Bedienungsanleitung

Denon

Denon AVR-X250BT Bedienungsanleitung

Denon

Denon AVR-550SD Bedienungsanleitung

Denon

Denon AVR-1610 Bedienungsanleitung

Denon

Denon AVR-2802 Bedienungsanleitung

Denon

Denon AVR-X2800H Bedienungsanleitung

Denon

Denon DRA-565RD Bedienungsanleitung

Denon

Denon AVR-2106 Bedienungsanleitung

Denon

Denon AVR-1802 Bedienungsanleitung

Denon

Denon AVR-4308 Bedienungsanleitung

Denon

Denon AVR 3802 Bedienungsanleitung

Denon

Denon AVR-1712 Kurzanleitung

Denon

Denon AVR-985SP Bedienungsanleitung

Denon

Denon AVR-E200 Bedienungsanleitung

Denon

Denon DRA-700AE Bedienungsanleitung

Denon

Denon AirPlay AVR-3311CI Bedienungsanleitung

Denon

Denon AVR-4308 Bedienungsanleitung

Denon

Denon AVR-X3400H Bedienungsanleitung

Denon

Denon AVR-X580BT Bedienungsanleitung

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Yamaha

Yamaha RX-830 Bedienungsanleitung

Pioneer

Pioneer AVH-Z7250BT Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Pioneer

Pioneer SC-LX904 Handbuch

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Pioneer

Pioneer SX-1000TA Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Pioneer

Pioneer SX-838 Bedienungsanleitung

Sherwood

Sherwood S-2660CP Technisches Handbuch

Sony

Sony STR-K790 - Lifier Bedienungsanleitung

Pioneer

Pioneer XR-VS77 Bedienungsanleitung