Dertec FP2SS Series Bedienungsanleitung
Quick installation guide
Read this rst.ENG
2021/Quick/ENG-001
2
DERTEC stainless steel motors are quality products.
It is very important that the instructions below are followed during installation.
In addition to following the standard safety instructions, the technician will need to be familiar with the correct installation of the
motors in damp working conditions.
Therefore, please read the instructions below carefully before installing and connecting DERTEC stainless steel drives.
General
• Disassembly of the motor is not permitted.
• Never remove the bearing shields!
• The warranty will be void if disassembly has been performed by anyone other than DERTEC employees.
To ensure proper operation, bearings, seals, O-rings and hygienic rings may only be replaced with OEM parts. Contact DERTEC or your
local agent for a repair kit.
To ensure proper operation, bearings, seals, O-rings and hygienic rings may only be replaced with OEM parts.
Contact DERTEC or your local agent for a repair kit.
FP2SS SL3SS
Installation instructions
3
DERTEC FP2SS Serie AC motoren
Open the cover of the junction box using an appropriate tool.
Prevent damage to the threads and O-ring.
Lightly grease the O-ring and close the terminal box. Prevent any
damage to the O-ring and make sure the cap is closed rmly.
Carefully remove the insulation from the earthing cable and get an
eye-type cable lug suitable for the cable used, with the corresponding
diameter. Fit the cable lug onto the earthing cable. Crimp the cable eye
to the earthing cable.
Route the cable through a suitable stainless steel cable gland into the
terminal box. In the example a stainless steel cable gland is used.
Check that the cable gland diameter matches the cable diameter you
are using. Ensure that the assembly and connection are performed so
as to maintain the protection class.
If the second cable entry will not be used, it must be thoroughly sealed
with the supplied stainless steel blind nut and O-ring.
The connection cable and conductor ferrule must be suitable for
temperatures up to 120 °C. Prepare the leads of the motor winding for
the correct connection(Y or Δ) according to the motor nameplate. The
red/black marked wires are for the PTCs. The yellow marked wires are
for the bimetal thermal protectors.
Connect the motor winding leads and the motor wires with suitable
crimp connections in accordance with the wiring diagram.
The same instructions apply for the built-in PTCs and bimetal thermal
protectors.
Connect the earth wire to the earth connection in the motor.
Installation instructions
4
DERTEC Signature line SL3SS serie AC motoren
Open the cover of the junction box using an appropriate tool.
Prevent damage to the threads and O-ring.
Carefully remove the insulation from the earthing cable and get an
eye-type cable lug suitable for the cable used, with the corresponding
diameter. Fit the cable lug onto the earthing cable. Crimp the cable eye
to the earthing cable.
Connect the motor winding leads and the motor wires with suitable
crimp connections in accordance with the wiring diagram.
The same instructions apply for the built-in PTCs and bimetal thermal
protectors. Connect the earth wire to the earth connection in the motor.
The power cable must correspond with the size of the cable gland.It
must t perfectly to ensure protection against moist.
Lightly grease the O-ring and blue hygiene ring. Grease the O-rings on
the central mounting pin. Place the terminal box cover over the central
mounting pin and make sure that the cable gland is positioned so that
the cable gland is facing down.Take the mounting bolt, grease the blue
sanitizer and place it around the mounting bolt.
Insert the mounting bolt into the center pin and tighten securely.
The O-rings offer sufcient protection against moisture penetration, the
blue hygiene rings ensure a hygienic seal.
Installation instructions
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Dertec Motor Handbücher
