Desa Wall Mantel and Base W26ME Gebrauchsanweisung

Shown with

Light Reed

Panels

If any wood pieces are missing or damaged, contact the

dealer where you purchased this mantel for replacement.

If hardware is missing or damaged, contact DESA Heating

Products at 1-866-672-6040 for referral information. You can

also visit DESA Heating Products’ technical service web site

at www.desatech.com.

Note: Gather all mantel pieces together before assembling

mantel.

WARNING: Use only 1/2" screws to attach metal

angle brackets. Damage to mantel will result if other

screws are used for this purpose.

ASSEMBLING MANTEL

IMPORTANT: More than one person is required to as-

semble and lift mantel.

Estimated assembly time: 45 minutes.

When assembling mantel do not tighten screws completely

until told to do so. There should be some play in the pieces

to allow for proper alignment and best possible t. It is very

important thatmorethanone personassemblemanteltogether.

Panels must be held in proper alignment to each other while

tightening screws to assure fewer gaps and proper surface

alignment. When tightening screws, do not over tighten. This

may cause threads to strip. For this reason, the supplied Allen

wrench should be used rather than a power screwdriver. The

panels have threaded inserts installed to mark your screw

locations. Screws should start and turn easily in threaded

holes when assembled according to instructions. Do not force

screws into holes.

IMPORTANT: There is a serial number label inside of right

side panel and on outside package. When calling to request

technical assistance or for replacement parts please have

that number ready.

W26ME WALL MANTEL AND BASE

ASSEMBLY AND INSTALLATION INSTRUCTIONS

IMPORTANT: Read entire instruction sheet before

assembling or installing mantel kit.

This mantel is only approved for use with any DESA

Heating Products 26" gas or electric replace system.

Do not use mantel with any other product.

This mantel kit contains the following:

• Mantel pieces - unassembled and marked as follows:

#1 Base

#2 Right Side with arrow

#3 Right Front Leg with arrow

#4 Left Side with arrow

#5 Left Front Leg with arrow

#6 Header with arrow

#7 Top

#8 Top Assembly Blocks (3)

#9 Header Assembly Blocks (2)

#10 Fruitwood (light) Left and Right Reed Panels (2)

#11 Fruitwood (light) Front Reed Panel

#12 Espresso (dark) Left and Right Reed Panels (2)

#13 Espresso (dark) Front Reed Panel

#14 Corner Trim (4)

• Hardware Kit*

12 - Metal Brackets 118937-01

24 - Screws M6 x 12 mm (1/2") 121149-01

20 - Screws M6 x 30 mm (1 1/4") 121335-01

20 - Washers M6 121336-01

1 - Allen Wrench 121337-01

*Extra hardware may be included.

• Perimeter Trim Kit 113140-02 (GAB6094)

www.desatech.com

Shown with

Dark Reed

Panels

www.desatech.com 122025-01A

LEG ASSEMBLY

1. Lay right side panel (#2) face down on a soft surface

to avoid marking nish. Attach three brackets with 1/2"

screws to bottom of right front leg (#3), leaving screws

slightly loose. Face brackets out toward tongued side

(see Figure 1). Place right front leg over right side (#2)

matching groove in leg to tongue on side, as shown in

Figure 1. Align threaded holes with brackets on side. Start

three 1/2" screws through brackets. Align bottom of side

and leg assembly so they are ush with each other. Hold

these pieces securely in alignment while tightening (but

not over tightening) screws.

2. Assemble left side (#4) and left leg (#5) as described in

step 1.

3. Attach 6 brackets to base (#1) at threaded hole locations

using 1/2" screws leaving screws loose. Face brackets

toward outside (see Figure 2).

Figure 1 - Right and Left Leg Assemblies

Figure 2 - Leg Assembly to Base

Figure 3 - Attaching Header

Tongue on

Leg Side

Groove in

Leg Front

1/2" Screw

Bracket

1/2" Screw

Bracket

Right

Side/Leg

Assembly

Header (#6)

Base (#1)

Leg Side (#2)

Leg Front (#3) Header

Assembly

Block (#9)

1 1/4"

Screw

Washer

4. Place right side/leg assembly on base and align threaded

holes with brackets. Start 1/2" screws through brackets

into threaded holes in side/leg assembly. Back of side/

leg assembly should be ush with back of base. Assure

alignment is correct and spaces are at a minimum. Leave

screws slightly loose.

Assemble left side/leg assembly to base following step #4.

HEADER ASSEMBLY

1. Start two 1 1/4" screws with washers through header as-

sembly block (#9) into threaded inserts on right side of

mantel. Repeat for left side (see Figure 3).

2. With arrow pointing up, place header (#6) into position on

top of leg assemblies and against header assembly block

(#9) (see Figure 3). Start two 1 1/4" screws with washers

through header assembly blocks (#9) into threaded in-

serts in header. Hold header in proper alignment with leg

assemblies and tighten, leaving screws slightly loose.

www.desatech.com

122025-01A 3

Figure 4 - Attaching Mantel Top

1 1/4" Screw

Washer

Mantel Top (#7)

Mantel Side

Assembly

FINISHING MANTEL

Starting with left side leg assembly, tighten screws using

Allen wrench provided. Tighten screws on the right side leg

assembly, header, top assembly and base.

MANTEL TOP ASSEMBLY

1. Start two 1 1/4" screws with washers through each of the

three header assembly blocks (#8) and into threaded

inserts on mantel as shown in Figure 4.

2. Place mantel top (#7) on mantel assembly. Align back of

top with back of sides. Using six 1 1/4" screws with wash-

ers, install two in each header assembly block (#8) (see

Figure 4). Make sure all pieces are aligned properly and

tighten all screws.

Top

Assembly

Blocks (#8)

Figure 5 - Installing Reed Panels

ELECTRIC FIREPLACE INSTALLATION

This mantel can be used with any DESA Heating Products

26" electric replace. Electric replaces install from the front

of mantel. To install electric replace see replace instruction

manual. Use caution when positioning replace on base. Base

may scratch easily.

REED INSTALLATION

1. Mantel kit contains two sets of reed panels. A dark set

(Espresso) and a light set (Fruitwood). Determine which

set you prefer. Store second set in safe, dry location on a

at surface to interchange in the future if you so desire.

2. Slide front reed panel (#11 or #13) into track on front of

mantel top (see Figure 5).

3. Slide left and right reed panels (#10 or #12) into tracks

on sides of mantel top. Be sure panel colors match.

4. Install 4 corner trim pieces (#14) by sliding onto dovetail

guide on mantel top (see Figure 5). Corner pieces should

slide on easily. Do not apply excessive force to prevent

breakage.

Note: Reed panels can be changed after installation.

122025-01

Rev. A

06/07

DESA Heating, LLC

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

GAS FIREPLACE INSTALLATION

1. Fireplace should be fully assembled. See Assembling

Fireplace in replace owner’s manual.

2. Place mantel base close to installation location. See re-

place owner’s manual for installation clearances. Leave

enough room to insert replace from back of mantel.

3. Install gas line. See Connecting to Gas Supply in replace

owner’s manual. Remember to leave access to the gas

shutoff valve somewhere on the base or where it is ac-

cessible to the user.

4. Check for leaks. See Checking Gas Connections in re-

place owner’s manual.

5. Position replace inside mantel (see Figure 6). Carefully

position gas lines. Important: Use caution when position-

ing replace on base. Base may scratch easily. Make

sure replace is in proper position within mantel opening

before continuing with installation.

6. Fireplace with louver door: Lower bottom louver door.

Use two screws provided in hardware package and attach

replace to wooden base. Close louver door.

Figure 6 - Installing Fireplace

Fireplace with xed louver: Before installing logs or

burner assembly (see owner’s manual) remove screws

securing oor to assembly. Lift oor for access to bot-

tom of replace. Use two screws provided in replace

hardware package and attach replace base to wooden

base. Reinstall oor with screws removed previously.

7. If mantel trim has not yet been assembled, see As-

sembling Perimeter Trim. Place metal trim on shoulder

screws. Firmly snap trim assembly over shoulder screws

on replace.

8. Carefully push mantel and base into position against

wall.

ASSEMBLING PERIMETER TRIM

1. Remove packaging from three pieces of metal trim.

2. Locate two adjusting plates with set screws, and two

shims in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 7.

4. Slide one end of adjusting plate/shim in slot on mitered

edge of top trim (see Figure 7).

5. Slide other end of adjusting plate/shim in slot on mitered

edge of side trim (see Figure 7).

6. While rmly holding edges of trim together, tighten both

set screws on the adjusting plate with slotted screw-

driver.

7. Repeat steps 2 through 6 for other corner.

Figure 7 - Assembling Trim

Side Trim

Slot

Top Trim

Mitered Edge

Shim

Set Screws

Adjusting

Plate

Slot

Inhaltsverzeichnis

Andere Desa Kaminzubehör Handbücher

Desa

Desa W26GO Gebrauchsanweisung

Desa

Desa PC-BDV37N Bedienungsanleitung

Desa

Desa Mantel and Base W26RO Gebrauchsanweisung

Desa

Desa Wall Mantel and Base with Trim W32WP Gebrauchsanweisung

Desa

Desa PCBM-325 Bedienungsanleitung

Desa

Desa W32AOSA Gebrauchsanweisung

Desa

Desa C32CO Gebrauchsanweisung

Desa

Desa Wall Mantel and Base W32MF Gebrauchsanweisung

Desa

Desa BDMO48E Bedienungsanleitung

Desa

Desa GA3555 Bedienungsanleitung

Desa

Desa Wall Mantel and Base W32LT Gebrauchsanweisung

Desa

Desa GB38 Bedienungsanleitung

Desa

Desa GA3700T Bedienungsanleitung

Desa

Desa Mantel and Base W21TO Gebrauchsanweisung

Desa

Desa W32GO Gebrauchsanweisung

Desa

Desa Wall Mantel and Base W32LS2 Gebrauchsanweisung

Desa

Desa Wall Mantel and Base W26LC Gebrauchsanweisung

Desa

Desa 102865-01 Bedienungsanleitung

Desa

Desa GS38 Bedienungsanleitung

Desa

Desa VCBK4L Bedienungsanleitung

Desa

Desa Comfort Glow GA3750 Bedienungsanleitung

Desa

Desa Wall Mantel and Base with Trim W32KCSA Gebrauchsanweisung

Desa

Desa Mantel and Base W26TO Gebrauchsanweisung

Desa

Desa GA6050 Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung