Desco 07010 Montage- und Bedienungsanleitung

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Employee Owned

Made in the

United States of America

Calibration Unit for Testers

Installation, Operation and Maintenance

Description

The Desco 07010 Calibration Unit is designed to verify

whether a tester is operating within specifications.

This product can be used as one of the tools to fulfill

the ANSI/ESD S20.20 paragraph 6.1.3.2 “Compliance

Verification Plan.” The 07010 Calibration Unit is a

passive device and requires no power source. The

Calibration Unit is manufactured with industry accepted

test ranges for both wrist straps and foot grounders.

The wrist strap pass range is set at 750K - 10M, while

the foot ground test range is set at 750K - 100M. The

Desco Calibration Unit is calibrated to NIST traceable

standards.

The Desco 07010 Calibration Unit is to be used with the

following items:

Item Description

19240 Wrist Strap Tester

19280 Combo Tester

19282 Combo Tester with Stand and Foot Plate

19283 Combo Tester with Stainless Steel Foot Plate

19350 Wrist Strap Touch Tester, 120VAC

19351 Wrist Strap Touch Tester, 220VAC

NOTE: The 07010 Calibration Unit also calibrates the

following discontinued items:

19250, 19252, 19253

March 2018

Figure 1. Desco 07010 Calibration Unit

Packaging

1 Calibration Unit

2 Test Leads with Banana Plug Terminals

1 Certificate of Calibration

Operation

WRIST STRAP TESTER

1. Plug one of the included test leads into the black

banana jack labeled “E” on the Calibration Unit.

Connect the opposite end of the test lead into the

yellow banana jack located on the 19240 Wrist

Strap Tester.

TECHNICAL BULLETIN TB-2039

Figure 2. Connecting the test lead from banana jack “E”

on the Calibration Unit to the banana jack on the Wrist

Strap Tester

2. Connect the second test lead to the red 675K

banana jack labeled “A” on the Calibration Unit.

Touch the opposite end of the test lead to test

plate on the Wrist Strap Tester and press down to

activate the test. Be sure not to touch the banana

plug or test plate with your skin.

3. Observe the response from the Wrist Strap Tester.

The alarm should sound, and the LOW LED should

illuminate red.

4. Repeat the procedure for test points B (825K), C

(8.5M) and D (11.5M). The expected test results can

be found in the following table:

Test

Point

Resistance

Value

Tester

LED

Buzzer

A 675K FAIL LOW ON

B 825K PASS OFF

C 8.5M PASS OFF

D 11.5M FAIL HIGH ON

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Employee Owned

Figure 3. Verifying the calibration of the Wrist Strap

Tester

COMBO WRIST STRAP / FOOTWEAR TESTER

Testing the Wrist Strap Circuit

1. Plug one of the included test leads into the black

banana jack labeled “E” on the Calibration Unit.

Connect the opposite end of the test lead into the

yellow banana jack labeled “WRIST STRAP” on the

Combo Wrist Strap / Footwear Tester. Toggle the

switch to the “WRIST STRAP” position.

2. Connect the second test lead to the red 675K

banana jack labeled “A” on the Calibration Unit.

Touch the opposite end of the test lead to test plate

on the Combo Tester and press down to activate

the test. Be sure not to touch the banana plug or

test plate with your skin.

3. Observe the response from the Combo Tester.

The alarm should sound, and the LOW LED should

illuminate red.

4. Repeat the procedure for test points B (825K), C

(8.5M) and D (11.5M). The expected test results can

be found in the following table:

Figure 4. Connecting the test lead from banana jack “E”

on the Calibration Unit to the WRIST STRAP banana

jack on the Combo Tester

Testing the Footwear Circuit

1. Plug one of the included test leads into the black

banana jack labeled “E” on the Calibration Unit.

Connect the opposite end of the test lead into the

yellow banana jack labeled “FOOT PLATE” on the

Combo Wrist Strap / Footwear Tester. Toggle the

switch to the “FOOT PLATE” position.

Figure 5. Verifying the calibration of the wrist strap

circuit in the Combo Tester

Figure 6. Connecting the test lead from banana jack “E”

on the Calibration Unit to the FOOT PLATE banana jack

on the Combo Tester

2. Connect the second test lead to the red 675K

banana jack labeled “A” on the Calibration Unit.

Touch the opposite end of the test lead to test plate

on the Combo Tester and press down to activate

the test. Be sure not to touch the banana plug or

test plate with your skin.

3. Observe the response from the Combo Tester.

The alarm should sound, and the LOW LED should

illuminate red.

4. Repeat the procedure for test points B (825K), C

(80M) and D (120M). The expected test results can

be found in the following table:

Test

Point

Resistance

Value

Tester

LED

Buzzer

A 675K FAIL LOW ON

B 825K PASS OFF

C 8.5M PASS OFF

D 11.5M FAIL HIGH ON

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Employee Owned

Figure 7. Verifying the calibration of the footwear circuit

in the Combo Tester

WRIST STRAP TOUCH TESTER

1. Plug one of the included test leads into the black

banana jack labeled “E” on the Calibration Unit.

Connect the opposite end of the test lead into one

of the yellow banana jacks located on the Wrist

Strap Touch Tester. Power the Wrist Strap Touch

Tester.

Figure 8. Connecting the test lead from banana jack “E”

on the Calibration Unit to one of the banana jacks on the

Wrist Strap Touch Tester

Figure 9. Verifying the calibration of the Wrist Strap

Touch Tester

2. Connect the second test lead to the red 675K

banana jack labeled “A” on the Calibration Unit.

Touch the opposite end of the test lead to test plate

on the Wrist Strap Touch Tester to activate the test.

Be sure not to touch the banana plug or test plate

with your skin.

3. Observe the behavior of the Wrist Strap Touch

Tester. The buzzer should not sound, and the TEST

GOOD LED should not illuminate.

4. Repeat the procedure for test points B (825K), C

(8.5M) and D (11.5M). The expected test results can

be found in the following table:

Test

Point

Resistance

Value

Tester

LED

Buzzer

A 675K FAIL LOW ON

B 825K PASS OFF

C 80M PASS OFF

D 120M FAIL HIGH ON

Test

Point

Resistance

Value

TEST

GOOD LED

Buzzer

A 675K OFF OFF

B 825K ON ON

C 8.5M ON ON

D 11.5M OFF OFF

Specifications

Accuracy ±5%

Dimensions 3.2" L x 4.4" W x .9" H

(8.1 x 11.2 x 2.3 cm)

Weight 4 oz (.1 kg)

Country of Origin United States of America

Limited Warranty, Warranty Exclusions, Limit

of Liability and RMA Request Instructions

See the Desco Warranty -

Desco.com/Limited-Warranty.aspx

Inhaltsverzeichnis

Andere Desco Prüfgeräte Handbücher

Desco

Desco TB-2071 Installationsanleitung

Desco

Desco 19250 Bedienungsanleitung

Desco

Desco 19443 Handbuch

Desco

Desco 19493 Fehlerbehebungshandbuch

Desco

Desco 19656 Handbuch

Desco

Desco 19650 Service-Handbuch

Desco

Desco EMIT 500524 Bedienungsanleitung

Desco

Desco 50005 Montage- und Bedienungsanleitung

Desco

Desco Combo Tester X3 Technisches Dokument

Desco

Desco 19640 Service-Handbuch

Desco

Desco 19780 Service-Handbuch

Desco

Desco 19245 Bedienungsanleitung

Desco

Desco 07010 Gebrauchs- und Pflegehandbuch

Desco

Desco 19493 Installationsanleitung

Desco

Desco 19250 Service-Handbuch

Desco

Desco 19770 Installationsanleitung

Desco

Desco 19780 Installationsanleitung

Desco

Desco 07010 Bedienungsanleitung

Desco

Desco 19240 Service-Handbuch

Desco

Desco 19276 Montage- und Bedienungsanleitung

Desco

Desco 19280 Montage- und Bedienungsanleitung

Desco

Desco TB-3041 Fehlerbehebungshandbuch

Desco

Desco Limit Comparator Bedienungsanleitung

Desco

Desco TB-3065 Montage- und Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung