DesignTech Smart Entry 20094 Bedienungsanleitung

V1.4

Smart EntryTM

Remote Keyless Entry

Model 20094/20994

For +12 volt vehicles with existing electric locks

Installation Manual

7955 Cameron Brown Court

Springfield, Virginia 22153 USA

Tel: 703-866-2000 ; Fax: 703-866-2001

20094/20994 Page 3Page 2 20094/20994

Congratulations on your purchase of the Smart Entrytm from DesignTech.

Smart Entrytm Protects You:

Lock and unlock your doors & trunk by remote control.

Optional Features Include:

Car Locator

Remote Panic/Rescue alarm

Turn on your headlights by remote control.

The transmitter which comes with the unit is already programmed to the

receiver and includes a long life lithium battery that will last many years.

CONTENTS:

Smart Entrytm Module

Transmitter (3 button)

Parts Baggie containing:

4 cable ties

2 "Protected by DesignTech" window stickers

Tools Required:

Test / Volt meter

Set of screw drivers

Wire cutter and strippers

Soldering iron and solder

Crimping tool

Smart Entrytm has a 10 amp headlight relay output. The unit also has

power transistors(+/-) to control Lock and Unlock. All other outputs are

negative transistor outputs (-400mA) and require external relays.

1. Mounting and Connecting the module:

Screws or cable ties may be used for mounting the module in the driver's

left kick panel area. We recommend mounting after everything has been

completed and tested fully. Be sure to leave access to the LED and red

push button on the side of the case for programming.

Make sure that the white antenna wire is as straight as possible and not

likely to be touching any moving parts. Make sure not to let this white

antenna wire touch metal ground as this will severely impede transmitter

range.

2. Wire Connections

Connect the wires in the harness by soldering the wires as perscribed be-

low. Do not connect the harness to the Smart Entry module until step 11.

A description of each wire in the harness and its connection as is:

1. BLACK Chassis ground. Strip off 1/2" of insulation of the end of the

wire and screw to the metal frame in the kick panel area.

2. RED +12 volts constant such as the ignition power feed in the

steering column area. (15 amp fuse must remain in-line).

3. BROWN/WHITE

This is the factory Alarm Disarm wire. This wire is used to

disarm a factory alarm when using this keyless entry module.

In most cases you will not need this wire unless an alarm sounds

when unlocking the doors by remote control.

4. ORANGE Ignition input -- connect to an ignition wire which has +12

volt when the key is in the ignition (normal running) position

but has no voltage when the key is out. This wire is optional

and when connected, prevents the unit from responding to the

transmitter when the ignition is on.

5. GREEN/WHITE

Trunk Release. For this option your trunk must have an

electric trunk release. This optional output is a (-400 mA)

STEP COLOR WIRE FUNCTION

20094/20994 Page 5Page 4 20094/20994

negative transistor output. In most cases you will need to use

an external relay (not supplied) when hooking up this wire.

See Page 8 for a detailed hook-up using a relay.

6. BROWN This is used for Dome Light activation. This optional wire can

control a relay to activate the dome light for 25 seconds after

the doors are unlocked with the transmtiter. This is a (-400mA)

negative transistor output. This wire must drive an external

relay.

7. BLUE Horn/Siren. This is an optional transistor output (-400 mA)

which can be used to drive a horn or be used with a relay to

drive a siren. If connecting to the horn, connect to a wire that

rests at +12 volts and switches to 0 volts when you honk the

horn. See programing options for changing this output from a

pulsed horn output to a constant siren output.

8. YELLOW The optional yellow wire activates the low beam headlights or

parking lights. This feature provides visual indication that

the doors have been locked or unlocked. Locate a wire that

switches to +12 volts when the lights are turned on.

9 & 10 Keyless Entry Wires

Note: Your vehicle must have electric locks

These are flip/flop transistor outputs (+/- 400mA)

WHITE/RED Negative - Lock Positive - Unlock

YELLOW/RED Negative - Unlock Positive - Lock

Determine the polarity of your door lock system using a test meter.

For Negative Locks (the lock wire sees a ground signal briefly as the electric locks are

locked) - connect the White/Red to the Lock wire and the Yellow/Red to the Unlock

wire.

For Positive Locks (the lock wire see a +12 volt signal briefly as the electric locks are

locked but does not see ground when they are inactive) - connect the White/Red to the

Unlock wire and the Yellow/Red to the Lock wire.

For Reversing Polarity (the lock wires sees a +12 volt signal briefly as the electric

locks are locked and sees a ground signal when they are inactive). Use the diagram at

the bottom of the previous page. Two Relays are Required

11. Powering Up The Unit

Plug the harness into the module at this time. Note that upon first power up -- the red

LED light on the module flashes 4 times slowly followed by rapid flashes and then

stops to indicate the unit is ready for normal operation.

20094/20994 Page 7Page 6 20094/20994

3. Horn-vs-Siren (Factory setting is Horn)

This product gives you the option of having a pulsed output for a car horn or a

constant output for a siren.

This section will set or reset any of the three options.

1) Push the red button on the side of the case of the receiver and the red LED

will flash once letting you know you are in option 1. Push the red button

again to scroll to option 2 (the LED will flash twice) and again for option 3

(the LED will flash 3 times) -- then back to option 1 again if necessary.

2) When you are at the option you want to change -- simply press the Middle

button on the transmitter to choose the function you want. After a few sec-

onds of holding the transmitter button down -- the red LED on the receiver

will flash once indicating you've set the optional setting or twice indicating

you've returned to the factory setting.

3) The unit will exit out of programming in 5 seconds by flashing the LED 3

times.

Follow the chart below and on the next page to set the features desired:

Option 1 — Lock Follow Ignition:

This option will lock the doors 2 seconds after the key is inserted into the ignition, and

will automatically unlock the doors when the key is removed from the ignition.

Factory (2 Flashes) Option (1 Flash)

No Lock Follow Ignition Lock Follow Ignition

Option 2 – Single Pulse / Double Pulse locks:

This option gives a double pulse to the Locks and Unlocks.

Factory (2 Flashes) Option (1 Flash)

Single Pulse Locks Double Pulse Locks

Option 3 — Horn-vs-Siren:

This gives an option for pulsed output for a horn or a constant output for a siren:

Factory (2 Flashes) Option (1 Flash)

Horn Output Siren Output

13. PROGRAMMING OPTIONS:

There are 3 options which can be changed

1. Lock Follow Ignition (Factory setting is "No Lock Follow Ignition")

This option will automatically lock the doors 2 seconds after the car is started, and

will automatically unlock the doors when the key is removed from the ignition

2. Single Pulse / Double Pulse Locks (Factory setting is Single Pulse)

This option gives a double pulse to Lock and Unlock the doors. The double

pulses are seperated by 1 second.

12. TRYING OUT THE UNIT:

Always keep one window rolled down to avoid locking yourself out of the vehicle.

Your transmitter has already been factory coded to the Smart Entrytm . (If it does not

trigger any of the following functions, and you have already checked your connec-

tions, follow the steps for Transmitter Code Learning at the end of the manual.) Gener-

ally, the transmitter button should be held down until the Smart Entrytm unit re-

sponds with the desired feature.

Button 1: Hold for one second -Lock (One chirp, One light flash)

Again: Hold for one second -Unlock (Two chirps, Two light flashes)

Hold for four seconds -Unlocks and opens Trunk

Button 2: Hold for One second -Car Locator (Brief Horn/Siren sound)

Hold for four seconds -Panic Alarm (45 second horn/alarm

sound)

Button 3: Hold for one second -Turns the Lights on for 25 seconds

Again: Hold for one second -Turns the Lights off

NOTE: If the Panic Alarm is sounding -- Button 2 held for 2 seconds will

turn off the Panic Alarm or the Panic Alarm will automatically

silence after 45 seconds.

20094/20994 Page 9Page 8 20094/20994

15. Transmitter Code Learning: Your Smart Entry module comes

factory coded to one of 16 million different codes and is already pro-

grammed. If you unit does not respond to your transmitter in any way after

checking the connections, or if you want to have additional transmitters

(up to 3 more for a total of 4) to trigger your Smart Entry module -- follow

the following directions:

1. Disconnect power for 5 seconds. Re-apply power - you will see

the LED flash 5 times quickly, then begin to flash rapidly.

2. While the LED is still flashing rapidly push the red button on the

side of the Smart Entry (the red LED will flash once) then push

and hold the left button on the transmitter for several seconds

until the red LED on the receiver comes on -- stop pushing the

transmitter button.

3. If you have a 2nd transmitter, within 5 seconds push the left button

on this transmiiter for a few seconds until the red LED on the

receiver comes on. Release transmitter button. Repeat for up to

4 total transmitters.

4. Wait 5 seconds for receiver to exit out of code learning mode --

the red LED on the receiver flashes 4 times.

Note: Teaching the module a new transmitter code will erase all

previously learned codes -- so all transmitters must be taught.

For any technical assistance regarding this product you may call DesignTech

on our toll-free telephone number - (800) 337-4468.

14. Example of optional Trunk hookup using an external relay:

Take a relay with 10 amp or higher capacity and a 12 volt coil. Locate the

push button for the trunk (usually in the glove compartment). You will

notice two wires behind this push button switch. Connect the Smart Entry's

Green/White Trunk wire to one side of the relay coil and constant +12 volts

to the other side of the coil.

If you are using one of the automotive industry standard relays like the

Bosch 30 amp relay -- the connections would be as follows:

Pin 85 (Positive side of relay's coil) +12 volts constant

Pin 86 (Negative side of relay's coil) Green/White wire

Pin 30 (Relay's common contact) One side of the trunk push button wire.

See Below

Pin 87 (Relay's normally closed contact) +12 volts

Pin 87a Not used

Example of Trunk hookup using an external relay:

20094/20994 Page 11Page 10 20094/20994

LIMITED WARRANTY

DesignTech International, Inc. Warrants to the original consumer/purchaser that this product shall be

free of defects in material and workmanship under normal use and circumstances for a period of two

(2) years from the date of original purchase for use. When the original consumer/purchaser returns

the product to DesignTech International Inc., 7955 Cameron Brown Court, Springfield, Virginia

22153, USA within the warranty period, and if the product is defective DesignTech International, Inc.

will at its option repair or replace such.

This warranty shall constitute the sole liability of DesignTech International, Inc. concerning the

product. DesignTech International, Inc. expressly disclaims all other warranties INCLUDING, WITH-

OUT LIMITATION, THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PAR-

TICULAR PURPOSE. NO PERSON, FIRM , OR CORPORATION IS AUTHORIZED TO ASSUME

FOR DESIGNTECH INTERNATIONAL, INC. ANY OTHER LIABILITY IN CONNECTION WITH

THE SALE AND USE OF THE PRODUCT. DesignTech International, Inc. and agents and distribu-

tors will bear no liability whatsoever for incidental or consequential damages or charges of any kind.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above disclaimer regarding incidental or consequential damages may not apply to you.

This warranty shall be effective only if the registration card is fully completed and mailed to: DesignTech

International, Inc., 7955 Cameron Brown Court, Springfield, Virginia 22153 USA within ten (10)

days after date of purchase.

This warranty is void if the product or has been damaged or tampered with or if the product or any

such parts have been opened. In all cases of damage during shipment, a claim must be filed with the

shipping carrier and not with DesignTech International, Inc.

This warranty gives you specific legal rights; you may also have other rights which vary from state to

state.

OUT OF WARRANTY REPAIRS

DesignTech International, Inc. will at its option either (1) replace this product with a functionally

similar (but not necessarily visually identical) refurbished product or (2) repair the original product

and return it to the original consumer/purchaser C.O.D. covering all reasonable repair or replacement

charges if the product is returned prepaid to DesignTech International, Inc., 7955 Cameron Brown

Court, Springfield, VIRGINIA 22153, USA after the two year warranty period has expired.

__________________________________________________________________________

This registration card must be returned within ten (10) days of purchase.

NAME__________________________________________________User's Age_________

ADDRESS________________________________________________________________

________________________________________________________________________

City State Zip

PLACE OF PURCHASE_________________________DATE OF PURHASE____________

Product Purchased:__Smart Entry 20094/20994____________________________________

Purchased for : __________YOURSELF _________SPOUSE

__________OTHER FAMILY MEMBER _________FRIEND

Where did you learn about this product?__________________________________________

Vehicle Make:__________________Vehicle Model:________________Year:____________

___________Please send me FREE information on other innovative DesignTech products.

7955 Cameron Brown Court, Springfield, Virginia 22153, USA

Tel: (703) 866-2000 Fax: (703) 866-2001

OTHER ACCESSORIES

A. Extra transmitters for more than one user in the family. Up to four transmitters can be used

with each Smart Entrytm.

B. Garage Door Receiver Unit will allow Your Smart Entrytm transmitter to operate an

electric garage unit.

C. You can remotely control your vehicle with our AutoCommand model 20022. Simply

pushing the lock button twice on your Smart Entry will start your vehicle.

These products are available through your dealer or directly from DesignTech :

3 button transmitter 20061 $49.95

30 amp relay with harness 20047 $17.95

Siren 20405 $49.95

Transmitter battery(CR2032) 20059 $7.95

Universal Garage Door Module 30021 $49.95

AutoCommand Remote Starter 20022 $99.95

All prices are in US Dollars and include shipping and handling.

7955 Cameron Brown Court nSpringfield, Virginia 22153 USA

Tel: 703-866-2000 nFax: 703-866-2001

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

FCC ID: ELGKEY2 DOC: _____________

User is cautioned that changes or modifications not expressly approved by DesignTech could

void the user's authority to operate this equipment.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DesignTech Fernbedienung Handbücher

DesignTech

DesignTech 29922 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung