Develop Ineo 164 Bedienungsanleitung

E-1

1BP0831301 A0XX-9635-00

INSTALLATION MANUAL

Applied Machine:

I. Outline of Installation Procedures for

ineo 164

Follow the notes below to install the printer and the

multi bypass tray.

Note:

• For the detailed installation procedures for the

multi bypass tray, see the Installation Manual,

and perform the procedures correctly.

• Once the power switch is turned on, do not turn

it off until the installation has been completed.

• When transporting or moving the printer, assign

adequate number of persons

(the printer mass: 23.5 kg/52 lb).

• This manual provides the illustrations of the

printer and the accessory parts that may be

slightly different in shape from yours. In that

case, instead of the illustrations, use the appear-

ance of yours to follow the installation proce-

dure. This does not cause any significant

change or problem with the procedure.

II. Installation Space (unit: mm (inch))

ineo 164 + MB-503

III. Pre-installation Check Items

1. Install the printer at a horizontal and stable place.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the printer directly from a dedicated power

outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

A0XXIXC001MA

A0XXIXC002MA

200

(8)

530 (20-7/8)

927 (36-1/2)

928 (36-1/2)

783 (30-13/16)

607 (23-7/8)

570 (22-7/16)

449(17-21/32)

856 (33-11/16)

E-2

IV. Accessory Parts

* Varies depending on the applicable marketing

area.

V. Unpacking the Printer

1. Unpack the packaging box, and remove cushion-

ing materials and plastic bags from the box.

2. While keeping the printer level, take out the

printer from the box.

Note:

Printer mass: 23.5 kg/52 lb

When transporting or moving the printer, assign

adequate number of persons.

VI. Removing Protective Tape, Packaging

Materials and Imaging Unit

1. Remove pieces of protective tape and packaging

materials.

2. Open the right and front doors.

3. Remove the cover shown in the illustration and

unplug the connector (one screw).

No. Name Q’ty

1. User’s Guide 1 set

2. Installation Manual (this manual) 1

3. Starter 1

4. Power Cord 1

5. Power Cord Instruction* 1

6. CD-ROM 1 set

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting your head in the wrapper involves

danger of suffocation.

A0XXIXC004MA

A0XXIXC005MA

A0XXIXC008MA

E-3

4. Unscrew the screws shown in the illustration to

remove the imaging unit (two screws).

Note:

• Do not touch or scratch the PC drum.

• Cover the imaging unit, which has been

removed, with a protective cloth or similar mate-

rial.

5. Close the front door.

6. Remove the protective tape.

7. Push the shafts in the direction of the arrows to

remove the fixing brackets that fix the transfer

roller.

8. Close the right door.

9. Slide out the drawer and remove the protective

tape and cushioning material.

10. Slide the drawer back in.

A0XXIXC012MA

A0XXIXC011MA

A0XXIXC006MA

Starter

E-4

VII. Loading the Starter

1. While pressing the connector tabs, push out the

connector from the imaging unit.

2. Unscrew the screws that secure the PC drum

unit, and then take out the PC drum unit by

slightly opening the lower part (the shadowed

area) of the PC drum unit (five screws).

Note:

• Do not open the lower part wide, otherwise the

charger may drop.

• Do not touch or scratch the PC drum.

• Cover the PC drum unit, which has been

removed, with a protective cloth or similar mate-

rial.

3. Remove the developing unit cover (three

screws).

4. Ready a packet of the starter and cut off one cor-

ner of the aluminum packet with scissors.

5. While turning the gear in the direction of the

arrow, pour the starter evenly into the developer

chamber.

Note:

• Turn the magnet roller in the direction of its nor-

mal rotation, and not the backward.

• Be sure not to let the starter get inside the collar.

6. Reinstall the developing unit cover, ensuring that

its tabs are fitted properly into the slits (three

screws).

Note:

Do not tilt the developing unit or imaging unit after

the starter is poured.

A0XXIXC040MA

Tabs

A0XXIXC013MA

PC drum unit

Developing unit

A11UIXC014MA

A11UIXC015MA

Collar

A11UIXC016MA

Temporarily tighten the screw first.

E-5

7. Install the front of the PC drum unit first, and then

the rear part. Then, secure the screws (five

screws).

Note:

• Do not open the lower part wide, otherwise the

charger may drop.

• Clean the screw groove before securing them.

• Do not touch or scratch the PC drum.

8. Attach the imaging unit connector that is removed

in step 1.

9. Slide the imaging unit into the printer, and then

secure the screws (two screws).

Note:

• Make sure that the right door is open when slid-

ing the imaging unit into the printer.

• Align the shaft of the imaging unit with the guide

of the printer.

10. Plug the connector, and then attach the cover

(one screw).

11. Close the right and front doors.

12. Plug the power cord to the printer, and then to a

power outlet.

VIII. ATDC Adjustment

1. Turn on the power switch.

2. Enter the service mode on the display.

(Refer to the Service Manual to display the ser-

vice mode screen.)

3. Press [+] or [-] key to select “FUNCTION” on the

display.

4. Press the [Menu/Select] key.

5. Press the [+] or [-] key to select “TCR AUTO

ADJUST.”

6. Press the [Menu/Select] key to execute the ATDC

adjustment.

The following message appears in two minutes.

TCR AUTO ADJUST

TCR GAIN: ***

7. Turn off the power switch.

A0XXIXC017MA

Temporarily tighten

the screw first.

Temporarily tighten

the screw first.

A0XXIXC019MA

A0XXIXC008MA

E-6

IX. Installing the Toner Bottle

Note:

A toner bottle is not shipped with your printer.

Purchase one that is separately available.

1. Shake the toner bottle well about five times in the

vertical direction. Then, turn it over and repeat

the same procedure.

Note:

The toner can cake in the toner bottle. Be sure to

perform this procedure.

2. Open the front door.

3. Insert the toner bottle halfway with the tape side

up, and then slowly peel the tape off the bottle.

4. Aligning the tip of the bottle tab with the

mark, insert the toner bottle all the way in.

5. Check that the toner bottle is all the way in, and

then turn the toner bottle in the direction of the

arrow to lock it.

6. Close the front door.

A0XXIXC018MA

Tape

A0XXIXC050MA

Andere Handbücher für ineo 164

Inhaltsverzeichnis

Andere Develop Drucker Handbücher

Develop

Develop QC 2235 Plus Bedienungsanleitung

Develop

Develop ineo 3301P Bedienungsanleitung

Develop

Develop ineo 4000i Bedienungsanleitung

Develop

Develop ineo 5000i Bedienungsanleitung

Develop

Develop ineo 958 Bedienungsanleitung

Develop

Develop ineo 3320 Bedienungsanleitung

Develop

Develop ineo 160 Bedienungsanleitung

Develop

Develop ineo 25e Bedienungsanleitung

Develop

Develop ineo 3300P Bedienungsanleitung

Develop

Develop D1531iD Bedienungsanleitung

Develop

Develop ineo 4000P Bedienungsanleitung

Develop

Develop ineo 3300P Bedienungsanleitung

Develop

Develop D 162F Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Develop ineo 164 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken