DeView DN22H485 Bedienungsanleitung

INSTRUCTION MENU

System Day/Night Camera

WARNING

To prevent fire or electric shock hazard, Do not expose this appliance to rain or

moisture.

RF EMISSIONS

This Class B digital apparatus complies with Canadian ICES-003.

Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

-reorient or relocate the receiving antenna.

-increase the separation between the equipment and receiver.

-connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

-consult the dealer or an experienced radio/TV technician for help

PREFACE

CB series camera introduces a new high picture quality , high resolution and high

sensitivity 1/3 inch type interline transfer CCD image sensor.

The CB series cameras have been developed using the advanced technology of

Digital Signal Processing LSI ( DSP ) together with On Screen Display control ( OSD ).

This series cameras is ideal for advance surveillance applications, or as an input

device for an mage processing system.

FEATURES

zHigh sensitivity with minimum illumination needed for quality video.

zLow image distortion and residual, withstanding electric and magnetic field

interference and mechanical vibration.

zApplications: Surveillance, Monitoring and Security.

zExcellent signal to noise ratio.

zAccurate color reproduction and 2 application range of Auto Tracing White

balance ( ATW ) over a wide color temperature.

zAperture and color suppression under low light to reduce spectral and Chroma

noise.

zAutomatic electronic shutter provides ＞1,600 : 1, equivalent to 40 steps,

dynamic range to correct exposure, if a manual iris lens is used.

zThe following functions are built in :

1 ) On Screen Display ( OSD ) digital control.

2 ) Internal and line lock synchronizations.

3 ) Auto IRIS ( AI ) / Auto Electronic Shutter ( AES ).

4 ) Auto IRIS level adjust by digital process on OSD manual.

5 ) 6 option for full application of Black Light Conversation ( BLC ).

6 ) Advance parameter adjust for application conditions.

7 ) 2 range Auto Tracking White balance ( ATW ) for indoor and outdoor

application conditions.

zThe back focus adjustment function allows easy adjustment and installation.

zExcellent picture quality

1 ) 2 edge ( vertical and horizontal ) picture enhancer for greater picture

sharpness.

2 ) New Chroma processing circuit for better color reproduction.

3 ) New concept ATW curve for good color emendation.

PRECAUTION

zDo not attempt to disassemble the camera.

To prevent electric shock, do not remove screws, case or covers. There are

no user serviceable parts inside. Ask a qualified service person for serving.

zHandle the camera with care.

Do not abuse the camera. Avoid striking, shaking, etc. The camera could

damage by any improper handing or storage.

zDo not expose the camera to rain or moisture, or try to operate it in

wet areas.

Take immediate action if the camera becomes wet. Turn power OFF and

refer servicing to a qualified service person for servicing. Moisture can

damage the camera and also create the danger of electric shock.

zDo not use strong or abrasive detergents when cleaning the camera

body.

Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove,

use a maid detergent and wipe gently.

zClean the CCD faceplate with care.

Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a

cotton tipped applicator and ethanol.

zNever face the camera towards the sun.

Permanent damage may occur when subjected to intense light. Whether the

camera is in use or not. Use cautiously when operating any electrical device.

Keep the camera out of the direction of spotlights and light reflecting objects.

zDo not operate the camera beyond the specified temperature, humidity

or power source ratings.

Do not use the camera in an extreme environment where high temperature or high

humidity conditions exist. Use the camera under conditions where temperatures

are within -10℃~ + 50℃, and humidity is below 80% relative humidity. The

input power source is 220VAC ~ 240VAC for AC230V model and DC12V/AC24V ±

20% for AC24V model camera.

zDo not touch the CCD sensor with your fingers. If necessary, use soft

cloth moistened with alcohol to wipe off the dust.

zWhen the camera is not in use, keep the cap on the lens to protect the

CCD sensor.

CAMERA DRAWING

PART DESCRIPTION

CONNECTION

Important Note:

Qualified service personnel or system installers should make the installation. Check

the power is OFF before handling the power cable no matter AC main power or low

voltage AC24V/DC12V.

A. Main Power Model (100VAC-240VAC 50Hz) :

1. Connect the AC power cord (supplied as standard accessory) to the power cord

socket of the camera.

2. Connect the AC power cord to an electrical outlet of AC100V ~ AC240V

50Hz/60Hz.

Notes:

zConnect the power cord firmly. The power cord should be long enough for

panning and tilting. If the cable is too short, the power cord plug may be

pulled off the camera when the camera pans or tilts.

zBrown: Live, Reference line lock. Blue: Neutral.

zThis camera voltage could accept range rated is AC90V ~ AC260V. But

recommend range is AC100V ~ AC240C.

B. Dual Power Model (12VDC/24VAC).

The series model has an AC/DC compatible input terminal. DC12V or AC24V

power supply cable can be connected to this terminal. The camera detects

the power source automatically.

Recommended wire gauge size. Φ0.65mm(AWG22), Stranded wire

0.32m ㎡(AWG22), Element wireφ0.18Min.

1. 12V DC Power Supply

Connect the power cable to the AC/DC compatible input terminal on the rear

panel of the camera. +12VDC should connect is the RED terminal. 0VDC

to the white terminal. Black terminal for Earth connection.

2. 24V AC Power Supply

Connect the power cable to the AC/DC compatible input terminal on rear

panel of the camera.

Notes:

zIf the cable is too short, the power cable may be pulled off the camera

when the camera pans or tilts.

zRed: Live, Reference line lock, Black: GND,. White: Neutral.

zVoltage range: Rated AC12V ~ AC28V. or DC10V ~ DC30V.

C. Video Cable

！

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

1. It is recommended to use a monitor whose resolution is at least equal to

the camera.

2. Set the termination switch to the 75Ωposition on the last monitor, and

to the Hi-Z position on the other monitors. Do not change the positions

after setting.

a. Use a 75Ωcoaxial cable.

b. The maximum extensible coaxial cable length between the camera

and the monitor is shown below.

RG-59/U RG-6U RG-11/U

Type of Coaxial cable 3C-2V 5C-2V 7C-2V

m 250 500 600

Recommended

Maximum

Cable length ft 825 1650 1980

3. Wiring precautions:

zDo not bend the coaxial into curve whose radius is smaller than 10

times cable’s diameter.

zNever staple the cable even if with circular staples. Impedance

mismatching will occur.

zNever crush or pinch the cable and cause poor picture quality.

D. Installation of Auto Iris Lens Connections

The camera supports Manual Iris Lens, Video Auto Iris Lens and DC Auto Iris

Lens. Use Video Auto Iris Lens or DC Auto Iris Lens is recommended for

outdoor application to prevent smear of the CCD.

1. Video Auto Iris lens

The connection terminal is on the rear panel of the Camera.

Refer the pin assignment (as Figure 1 at Right ) is necessary to insure

correct operation.

Recommended wire gage:

Solid wire : φ1.2mm(AWG16), Stranded wire :

0.25m ㎡(AWG16), Element wire : φ0.18Min.

Pin assignment

GND : Shield, ground.

+12V : Power source; +12VDC, 50mA Max.

Video : Video signal output.

2. DC Auto Iris Lens

The 4pin connection terminal is on the rear panel of the Camera.

Refer the pin assignment is necessary to insure correct operation.

G. Mounting the Lens

1.Mount the lens by turning it clockwise on the lens mount of the camera.

2.Connect the lens cable to the auto iris lens connector on the rear panel of

the camera.

Caution for Mounting the Lens

The lens mount should be a CS –mount (1”-32UN) and the lens weight

should be less than 450g (0.99 lbs). IF the lens is heavier, both the lens

and camera should be secured by using the supporter.

H. Focus and Back Focal Adjustment

The following adjustment should be made by qualified service personnel or

system installers.

1. Loosen the screw of back

focus adjust on the topside of

front head.

2. Move the back focus adjust screw

to the desired position.

3. Fixing the screws on the back focal adjusting screw.

Caution:

Do not fix the back focus screw too tight, otherwise the back

focus mechanize unit might be damaged. Finger tight only.

When the C-mount lens is mounted, do not rotate the ring

Counter clockwise by force after it. If the ring is rotated by

force, the inner lens or CCD image sensor may be damaged.

I. LAMP Contact

To prevent mechanize OLPF hunting, this camera equipped the

external contact terminal with IR lamp control. Connect to GND that

switch camera to nighttime mode immediately.

Caution :

When use IR illuminations, use a lens that is

compatible with the IR illuminations.

Any lens other than the compatible one

can result out of focus due to such

characteristics.

J. RS485

Terminal for remote control by EIA/TIA RS485 format,

refer pin assignment to have correct connection.

Those cables should 0.654 conductor twisted

pair cables. With these cables the max

extension distance is 1,000m. 3

CS Lens mount,

1"-32 UNF

Back Focus Adjust

Back Focus Fix Screw

DC Auto IRIS

Output Connector

BNC,

Video Output

Terminal Block,

Power Input

Video Auto IRIS Drive Output.

RS-485 Controller.

IR Lamp Contect.

Power Input.

110VAC ~ 240VAC

OSD menu, Arrow Key.

OSD menu, Enter Key.

Mounting screw hole,

¼", 7mm deep.

Rotation preventive hole

VIDEO LENS

GND

+12V

VIDEO

GND

LAMP

RS485

Pin 1 Damp +

Pin 2 Damp -

Pin 3 Drive +

Pin 4 Drive - Pin 1

Pin 2 Pin 3

Pin 4

GND

LAMP

RS485

OSD Menu Operation

A. OSD menu flow chart

The function indicated with * for default setting.

B. Tact Switch Operation

This camera utilizes a user menu “ Set Up Menu “ that is displayed on the

monitor. To set items on the “ Set Up Menu “, use the following buttons on

the side panel.

UP Key: This button is used to move the cursor upwards.

Down Key: This button is used to move the cursor downwards.

Right Key: This button is used to move the cursor to the right.

Use this button to select or adjust the parameters of the selected item.

The parameter changes each time this button is pressed.

Left Key: This button is used to move the cursor to the left.

Use this button to select or adjust the parameters of the selected item.

The parameter changes each time this button is pressed.

Set Key: This button is used to set the determined parameter. If the item

has its own setting menu ( indicted by ), press this button to display the

next page setting menu.

C. Opening the Set Up Menu

Press SET Key for three second. The

“ SET UP MENU “ will appear on the

monitor as shown on right side. Check

the current settings on the menu.

Refer to the sections below for a

detailed description of menu items. If

you decide not to make any changes

after checking the current settings,

move the cursor to “ QUIT“ and press

SET Key to close the “ SET UP MENU

“ and return to normal camera picture.

D. Reset

Reset allows you to reset all setup menu items to the factory settings if you are

unsure about the correct settings. Proceed as follows: Move OSD cursor to

“ Reset “ and press SET Key. The words “ Resetting “ momentarily appear on

the monitor. At this time all adjustments and parameters are reset to the

factory default settings.

Note:

If no button is pressed for 30 second while the OSD menu or any other setting

menu is displayed, the menu is automatically canceled and returns to the normal

camera picture.

FUNCTION OPERATION

1. Synchronization Setting (SYNC)

You can select internal sync mode (INT) or line-lock mode (LL).

a. Use UP Key and Down Key move the cursor to the Sync parameter and use

Right Key or Left Key to select line-lock ( LL ) or internal ( INT ), and press

SET Key.

b.If LL is selected, the Sync second menu appears, If INT is selected, the

synchronization mode is automatically set to internal sync , and the menu is

displayed INT.

1-1. Line-lock Sync Mode (LL)

The line-lock mode has its own menu for line-lock vertical phase adjustment.

When the vertical phase adjustment menu appears on the monitor. use Right

Key or Lift Key to move the cursor for phase adjustments. If the camera

installation is relocated, check the vertical phase adjustment again since the AC

line phase may be different.

Note: The line-lock ( LL) sync mode is not available when the camera operates

on DC power.

How to make sure the Phase:

Set the oscilloscope to the vertical rate and expand the vertical sync portion on

the oscilloscope.

Press Right Key or Lift Key of the camera to match the vertical phase for both

video output signals as closely as possible.

Phase adjustment range can be incremented in 16 steps by 22.5 degrees.

When Right Key or Lift Key is kept pressed for a second or longer, the " I "

cursor moves faster.

Note : If the AC line contains noise (spike noise, etc.), the stability of

the vertical phase of the camera video output signal may be disturbed.

2. Shutter Speed Setting (Shutter)

To select electronic shutter speed, you can select an manual electronic shutter

speed of 1/50 (1/60), 1/120 (1/100). 1/250. 1/500, 1/1000, 1/2000, 1/4000,

1/10000 seconds. Or Auto Electronics Shutter ( AES ). The 1/50 (1/60) is shutter

OFF. This function is effective to raise the sensitivity in low light conditions when

OFF is selected for Auto IRIS Lens. Move the cursor to the Shutter parameter

and select the electronic shutter speed. The preset values for Shutter (electronic

shutter speed) change by pressing Right Key or Lift Key as follows:

3. Lens

3-1 Bright

This item is used to adjust the level of auto iris tens drive which supplied to DC

drive lens or video iris lens. Before operation make sure that connection is

correct for video auto iris lens or DC auto iris lens.

a. Move the cursor to the Lens parameter and press SET Key, the second

menu of Lens is appear on the monitor.

b. Change the curser by Right Key or left Key to adjust IRIS to close or open.

Once the picture is optimum move curse to Back and press SET key to safe

setting and return to top menu.

3.2 BF

This function is allow installer very easy to adjust optical back focus. When used

auto iris lens, this function will automatically fully open the IRIS of lens and change

to AES ( auto electronics shutter ). In case of manual lens, this function will

automatically switch to AES.

a. Move curse to Lens by Control Key, change to BF and press SET key. In

the meantime “ Press SET for return” is display on monitor.

b. Adjust optical back focus to optimum position that press SET key for return to

top menu. ( Please refer to section H Focus and Back Focal Adjustment )

4. BLC

This provide camera incase face strong light to have compensation luminance on

monitor. There are six BLC pattern and each are could adjust compensation level.

Compensation area indicated as below

5. Configure

5-1. Aperture, Move the curse to Aperture and press SET key. The second menu

will appear. Move the “ I “ to adjust V-Aperture and H-Aperture level.

5-2. Gamma, Move the curse to Gamma and press SET key. The second menu will

appear. Use Lift and Right key to select gamma 0.45, 0.8 or 1.

5-3. Pedestal, Move the curse to Pedestal and press SET key. The second menu

will appear. Move the “ I “ to adjust pedestal level.

5-4. Chroma, Move the curse to Chroma and press SET key. The second menu

will appear. Move the “ I “ to adjust Chroma level.

5-8. AGC, 7 limited value could select to limit enhance gain of AGC circuit, also select

OFF could closed AGC function and select Sens Up to have maximum value (38dB) of

AGC gain.

6. White Balance

6-1. WB-Auto ( White Balance Auto), In this mode, the color temperature is

monitored continuously and thereby white balance is set automatically. The color

temperature range for the proper white balance is approximately 2500 - 9100K.

6-2. WB-Menu (White Balance Menu), This mode provide user to adjust

white balance by manual adjust, There are R-gain and B-gain could adjust

independent.

6-3. WB-Push, Move curse to WB-Push. Press on SET key to start the white

balance tracing. When the white balance setting is completed, release SET key and

push white was completely.

7. CAM Title

The camera provide text generation on the display monitor. The 16 character in one

line is available for CAM Title function.

8. D/N

This function provide camera automatically switch from color camera to B/W

camera by auto detect luminance, manual switch or external contact terminal by

IR lamp on rear panel.

8-1. Fuzzy, The camera switch to B/W camera by auto detect luminance.

D/N Level, the detect level could be select by Low or High.

Burst On, Keep Burst signal when camera changes to B/W mode.

Burst Off, Remove Burst signal when camera changes to B/W mode.

8-2. IR Pass, Change camera to B/W camera by selects this function.

Burst On, Keep Burst signal when camera changes to B/W mode.

Burst Off, Remove Burst signal when camera changes to B/W mode.

8-3. IR Cut, Close Day/Night function, keep camera on color mode, at this

mode the camera will not accept IR luminance.

9. RS485

Before operation is function make sure correct connection on rear panel for

RS485.

Provide 000 ~ 999 ID address, 3 Password to protect RS485 setting.

Use arrow key to move curse to RS485 and press SET key,

Password, Before into RS485 setting. Camera system request 3 character

password, input correct password to second menu.

Note, before password change the default password is 000.

Address, provide 000 ~ 999 ID address. Wrong address ID setting both

control and receive will cause remote control no function.

B-rate, Baud rate setting, provide 2 rate select 4800 or 9600.

Note, Incorrect baud rate setting will cause remote control no function.

Package

Camera 1pcs.

InstructionManual 1pcs.

CCDProtectCover 1pcs.

Main Power Cable ( Main power model only ) 1pcs

Specification

General PAL Model / NTSC Model

Image Size 1/3 Format Interline CCD Sensor

Pixel Element PAL Model : 768 (H) ×582 (V) approx. 440K pixels

NTSC Model : 768(H) x 494 (V) approx. 380K pixels

Scanning Frequency PAL 2 : 1 Interlace / H : 15625Hz , V : 50Hz

NTSC 2: 1Interlance / H : 15750Hz, V : 60Hz

Operation Temperature -10℃~ +50℃

Storage Temperature -20℃~ +60℃

Output Terminal BNC 75Ohm Unbalance

Power Source Dual Switching Mode Power Supply DC12V / AC24V ±20%

Universal Switching Power Supply AC100V ~ AC240V

Power Consumption 4.5 W Max,

Power Indicator 3θGreen LED on Rear Panel

IRIS Connector 4 pin Connector For DC Drive Lens ( Panasonic Standard )

3pin Terminal Block For Video Drive Lens

Lens Mount CS Mount, Change C Mount by Adaptor.

Mounting Hole 1/4” Top and Bottom

External Dimension 73mm (W) x 63mm (H) x 122mm (D)

Weight TBD

Functional Specification

Auto IRIS Control Video Drive / DC Drive Separate Output

* Day & Night Optical Low Pass Filter Removable

* IR Lamp Trigger External Relay Contact for GND Loop

Chroma Separate CS / Color Killer

* Color Killer ON / OFF / Fuzzy

SYNC System INT / Line Lock

Line Lock Phase Adjust Range 0°~ 270°

Frequency Range PAL 50Hz ±1Hz / NTSC : 60Hz ±1Hz

Remote Controller RS-485 two way communications

Camera Addressable 001 ~ 999

Text Display 16 Character with one line

Resolution 470 TV Line

Minimum Illumination 0.5Lux @F=1.2 ( 50IRE Video Output )

Video Output 1.0Vpp 75Ohm BNC unbalance

S/N Ratio 50dB

Gamma Compensation 3 Curve Selectable ; 0.45 / 0.8 / 1

Function Control or Selectable By OSD and RS-485

SYNC System INT / LL Selectable

V-Phase 0°~ 270°

Exposure Control Auto Electronics Shutter / Manual Electronics Shutter

/ Auto IRIS lens

Auto Electronics Shutter Max, Limit and Level Adjustable

Menu Electronics Shutter 8 Step 1/50 (1/60), 1/120 (1/100) , 1/250 , 1/500

1/1000 , 1/2000 , 1/4000 , 1/10000

Auto IRIS Lens Driver Video IRIS lens / DC IRIS lens

Lens Level Control Both For DC IRIS Lens and Video IRIS Lens

BLC 6 Area Select and Level Adjustable; Center 1, Center 2,

Door Way 1, Door Way 2, Upper Half, Lower Half.

White Balance Control Auto White Balance / Push White Balance /

Menu White Balance

Auto White Balance 2 Application Range Selectable;

2500K ~ 9500K / 2000K ~ 18000K

Menu White Balance 1 Preset; R gain / B gain Adjustable

Gain Control Auto Gain Control

Auto Gain Control 12dB ~ Sensitivity up (38dB max.) Adjustable.

Gamma Control 3 Step Selectable; 0.45 / 0.8 / 1

Aperture Control 0 ~ 15 IRE Max. For Vertical and Horizontal

Chroma Level Adjustable

* Color Killer ON / OFF / Fuzzy Selectable

* Day/Night IR Pass / IR Cut / Fuzzy

Remote Control RS-485, Two way communications

Address 001 ~ 999 ID selectable

Note : Function indicated * for System Day/Night model only.

Document Nr. : TOM-20030606-01B

Version Nr. : 030804A

Part Nr. : 531-CD000-000

Set key

Right key

Down key

Up key

Left key

Detect

Area

CENTER 1 CENTER 2

Detect

Area

DOORWAY 1

Detect

Area

DOORWAY 2

Detect

Area

LOW HALF

Detect

Area

UP HALF

Detect

Area

TOP MENU SECOUND MENU THIRD MENU

Lens Bright

Configure

Chroma Level

Pedestal Level

Aperture H-APT Level

V-APT Level

Sync INT *

LL V-Phase

BLC Off *

Center 1

Center 2

Door Way 1

Up Half

Low Half

Level

Door Way 2

Gamma 0.45 *

0.8

RS485 Address _ _ _

B-Rate 9600dps *

Address

4800dps

Password Setting Password _ _ _

Shutter AES 1/2K

1/60(1/50) *

1/100(1/120)

1/250

1/500

1/1K

1/2K

1/4K

1/10K

Bright

1/5K

1/10K

1/20K

1/50K *

1/100K

Text

CAM Tilte

Position

Off *

D/N IR Pass

IR Cut

Burst On

Burst Off *

Fuzzy

D/N Level Low

D/N Level High

Burst On

Burst Off *

AGC Off

18dB

26dB

30dB *

32dB

34dB

Sens Up

36dB

22dB

R-Gain

B-Gain

2500K ~ 9500K *

2000K ~ 18000K

WB - Auto *

WB - Menu

WB - Push

White Bal

Set up Menu

Sync Int

Shutter

Lens

BLC

Configur

White B

Cam Tit

D/N

1/50

Bright

Off

e Aperture

al AWB

le Off

Fuzzy

RS-485 Address

Exit ResetQuit

TOP MESECOUND MENUTHIRD MENU

BFLensBrightConfigureChromaLevelPedestalLevelApertureH-APT LevelelV-APT LevSyncINT*LLV-PhaseBLCOff*Center 1Center 2Door Way 1Up HalfLow HalfLevelDoor Way 2Gamma0.45*0.81RS485Address _ _ _B-Rate9600dps*Address4800dpsPassword SettingPassword _ _ _ShutterAES1/2K1/60(1/50)*1/100(1/120)1/2501/5001/1K1/2K1/4K1/10KBright1/5K1/10K1/20K1/50K*1/100KTextCAM TiltePositionOff