DeVilbiss QM T-5 Series Referenzhandbuch

SERVICE BULLETIN

SB-21-064-J

Replaces SB-21-064-I

IMPORTANT: Read and follow all instruc-

tions and SAFETY PRECAUTIONS before

using this equipment. Retain for future

reference.

5, 10, 15 GALLON QMS TANKS

(STAINLESS STEEL)

DESCRIPTION

DeVilbiss pressure feed tanks are intended

for use as a pressure container to supply

material at a constant preset pressure up to

a maximum of 110 psi. The tanks are built to

ASME specifications, and are FM approved.

DeVilbiss pressure tanks are also certified

for vacuum operation.

NOTE

These pressure tanks are constructed

from stainless steel and other non-

reactive materials. Materials con-

taining halogented solvents can be

used safely with these tanks.

Standard Nonregulated Tanks

(No Regulation)

Standard type tank for use to distribute

“regulated” air by remote filter/regulator or

other similar control to pressure tank.

Equipped with pressure gauge, safety valve,

air bleed down valve, and air inlet valve.

Standard Fluid Regulated Tanks

(Single Regulation)

Standard type tank for use on jobs where

precision control of both fluid and atomiza-

tion air pressures is not required. Also used

where atomization air can be taken from

filter/regulator air lines. Provides standard

fluid pressure control only. Equipped with

pressure regulator, pressure gauge, air bleed

down valve, safety valve, and inlet and

outlet air valves. (For conversion to double

regulation, use kit QMS-436.)

Standard Air and Fluid Regulated Tanks

(Dual Regulation)

Precision controlled tanks for use with

materials that are best applied at low,

closely controlled, fluid and atomization air

pressures. Used with portable air compres-

sors or with air lines when no other means

of air pressure regulation (filter/regulator)

is available. Equipped with two regulators

(one for fluid pressure, the other for atomi-

zation air pressure), two pressure gauges,

air bleed down valve, safety valve, and

inlet and outlet valves.

Extra Sensitive Fluid Regulation

Tanks especially adapted for use with elec-

trostatic spray installations, application of

lubricants, special coatings, etc. Suitable for

use wherever extremely sensitive, non-fluc-

tuating low pressure control is required.

Large, reinforced, synthetic diaphragm

type regulator controls to a maximum of

30 pounds pressure. Equipped with extra

sensitive pressure regulator, pressure

gauge, air bleed down valve, safety valve,

inlet valve, and unregulated outlet valve.

Agitation

Pressure tanks can be equipped with differ-

ent types of fluid agitation, or no agitation.

Hand agitation or air agitators are provided

to suit any application.

Refer to specifications chart to ensure

that fluids and solvents being used

are chemically compatible with the

tank wetted parts. Before placing

fluids or solvents in tank, always

read accompanying manufacturer’s

literature.

Air pressure loads that are higher

than design loads, or changes to the

pressure feed tank, can cause the

tank to rupture or explode.

•Asafety valve protects the tank

from overpressurization. During

each use, pull ring on the safety

valve to make sure it operates freely

and relieves air pressure. If the valve

is stuck, does not operate freely, or

does not relieve air pressure, it must

be replaced with a safety valve

having the same rating. Do not

eliminate, make adjustments to, or

substitute this valve.

•Changes to the air tank will

weaken it. Never drill into, weld, or

change the tank in any way.

•Maximum working pressure of

this tank is 110 psi.

MODEL NUMBERS

The model numbers are coded with specific

information for each character and position

in the number. Refer to the following table

for an explanation of each position and

meaning for each character in the model

number. Use this information in selecting

the proper model from the MODEL APPLI-

CATION TABLE.

TYPE OF REGULATION

0= NONE

1= ONE REGULATOR

2= TWO REGULATORS

3= EXTRA-SENSITIVE

T = TOP FLUID

OUTLET

PRODUCT

IDENTIFICATION

QM T -5

G = GALVANIZED

S = STAINLESS

STEEL

COMPLETELY

FACTORY

ASSEMBLED

TANK SIZE

5= 5-GAL

10 = 10-GAL

15 = 15-GAL

TYPE OF AGITATION

0=NONE

2=HAND

3=QS-5012(STD)

6=31-381

(RECIPRO-

CATING)

Page 2SB-21-064-J

SAFETY PRECAUTIONS

This manual contains important information that all users should know and understand before using the equipment. This information

relates to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the following terms

to draw your attention to certain equipment labels and portions of this Service Bulletin. Please pay special attention to any label or

information that is highlighted by one of these terms:

Important information to alert you

to a situation that might cause

serious injury if instructions are not

followed.

Important information that tells how

to prevent damage to equipment, or

how to avoid a situation that might

cause minor injury.

NOTE

Information that you should pay

special attention to.

The following hazards may occur during the normal use of this equipment. Please read the following chart.

HAZARD CAUSE SAFEGUARDS

Fire

Solvents and coatings can be highly 1. Adequate exhaust must be provided to keep

flammable or combustible, especially the air free of accumulations of flammable

when sprayed. vapors.

2. Smoking must never be allowed in the spray

area.

3. Fire extinguishing equipment must be present

in the spray area.

Fire - Pressure Tank

Vapors from flammable liquids 1. Keep tank at least 10 feet away from sources

can catch fire or explode. of ignition. Ignition sources include hot objects,

mechanical sparks, and arcing (non-explosion

proof) electrical equipment.

InhalingToxic Substances

Certain materials may be harmful if 1. Follow the requirements of the Material

inhaled, or if there is contact with the skin. Safety Data Sheet supplied by your coating

material manufacturer.

2. Adequate exhaust must be provided to keep

the air free of accumulations of toxic materials.

3. Use a mask or respirator whenever there is a

chance of inhaling sprayed materials. The mask

must be compatible with the material being

sprayed and its concentration. Equipment must

be as prescribed by an industrial hygienist or

safety expert, and be NIOSH approved.

Explosion, Pressure

Making changes to pressure 1. Never drill into, weld, or modify tank in any

Tank - Rupture

tank will weaken it. way.

2. Do not adjust, remove, or tamper with the

safety valve. If replacement is necessary, use

the same type and rating of valve.

General Safety

Improper operation or maintenance may Operators should be given adequate training in

create a hazard. the safe use and maintenance of the equipment

(in accordance with the requirements of NFPA-33,

Chapter 15 in U.S.). Users must comply with all local

and national codes of practice and insurance

company requirements governing ventilation, fire

precautions, operation, maintenance and housekeep-

ing (in the U.S., these are OSHA Sections 1910.94

and 1910.107, and NFPA-33).

SB-21-064-J Page 3

DIMENSIONS

INSIDE

INSIDE HEIGHT OVERALL OVERALL

TANK SIZE DIAMETER AT CENTER HEIGHT* WIDTH WEIGHT*

(Inches) (Inches) (Inches) (Inches) (Pounds)

5 Gallon 14 16 20-5/16 18-1/2 51

10 Gallon 14 19-1/16 23-3/8 18-1/2 54

15 Gallon 14 29-1/16 33-3/8 18-1/2 78

*Basic tank, not including regulators or agitation.

MODEL APPLICATION TABLE

MODEL NUMBER AGITATOR REGULATOR

5 GALLON 10 GALLON 15 GALLON TYPE/DRIVE TYPE NUMBER

QMST-5500 QMST-51000 QMST-51500 None None QMS-4003

QMST-5510 QMST-51010 QMST-51510 None Single QMS-4006

QMST-5520 QMST-51020 QMST-51520 None Double QMS-4007

QMST-5502 QMST-51002 ———— Hand/Crank None QMS-4003

QMST-5512 QMST-51012 QMST-51512 Hand/Crank Single QMS-4006

QMST-5513 QMST-51013 QMST-51513 Std/Air Single QMS-4006

QMST-5523 QMST-51023 QMST-51523 Std/Air Double QMS-4007

QMST-5516 QMST-51016 QMST-51516 Recip/Air Single QMS-4006

QMST-5526 QMST-51026 QMST-51526 Recip/Air Double QMS-4007

———— ———— QMST-51530 None Ex Sen QMS-4010

QMST-5533 QMST-51033 ———— Std/Air Ex Sen QMS-4010

Static electricity is created by the flow of

fluid through the pressure tank and hose. If

all parts are not properly grounded, sparking

may occur. Sparks can ignite vapors from

solvents and the fluid being sprayed.

If static sparking, or slight shock, is

experienced while using this equipment,

stop spraying immediately.

Ground the pressure tank by connecting

one end of a 12 gauge minimum ground

wire to the pressure tank and the other end

to a true earth ground. Local codes may

have additional grounding requirements.

If using an air quick disconnect (Q.D.) at the

inlet to the regulator at the pressure tank,

do not disconnect the Q.D. while the tank is

pressurized, unless the ball valve is closed.

Doing so will allow tank pressure to quickly

relieve, and can potentially pull paint back

through the air regulator and air motor

depending upon the liquid level in the tank.

Tank pressure should always be relieved

by opening the pet cock (relief valve) or

pulling the safety valve ring.

NOTE

(For non-direct drive models)

A tank with agitator assembly is shipped with the

curved edge of the paddle down. When a steel

insert container is used it is necessary to turn the

bottom paddle upside down so that the flat side is

down. In either position, the correct adjustment

on the paddle position is with the end of

the paddle hub flush with end of the shaft. This

mounting should give 1/2 inch clearance between

the edge of the paddle and the insert container.

Pressure Relief Procedure

High pressure can cause a serious

injury. Pressure is maintained in a

pressure tank after the system has

been shut down. Before attempting

removal of fill plug or cover, pressure

must be relieved using the following

steps:

1. Turn off the main air supply

to the tank.

2. Close air inlet valve located

on tank air manifold.

3. Bleed off air in the tank by turning

the air relief valve thumb screw

counterclockwise. Wait until all the air

has escaped through the valve before

removing the pressure tank cover or

fill plug.

4. Leave the air relief valve open

until you have reinstalled the

cover or fill plug.

Mix and prepare material to be used according to

manufacturer’s instructions. Strain material

through a fine mesh screen to remove lumps,

skin, and foreign matter that might enter and clog

fluid passages and/or spray equipment.

SPECIFICATION CHART

Maximum Working Pressure ............. 110 PSI

Tank Shell ............................................ 304 Stainless Steel,

.............................................................. 13 gauge (.0897 in.) thick

Tank Lid ............................................... 304 Stainless Steel,

.............................................................. 3/16 in. thick

Agitator Shaft ...................................... 303 Stainless Steel

Fluid Tube ............................................ 316 Stainless Steel,

.............................................................. 3/8 in. pipe

Fluid Valve, Outlet .............................. 316 Stainless Steel,

.............................................................. 3/8-18 NPSM outlet

Air Manifold ........................................ CRS - zinc plated

Shaft Seal ............................................ Engineered Teflon,

.............................................................. Stainless Steel

Agitator Paddles ................................. Nylon, Glass Filled

Fluid Outlet .......................................... 316 Stainless Steel

Bottom Outlet (Optional Kit) .............. 304 Stainless Steel,

.............................................................. 3/4 in. NPSM outlet

TO ASSEMBLE REGULATORS AND HOSE TO TANK

Assemble

single

regulator to

manifold

using

an 11/16

wrench.

Assemble

double

regulator

to manifold

using

an 11/16

wrench.

Assemble

hose to

either

manifold

using a 5/8

wrench.

PTFE

Page 4SB-21-064-J

1. Follow pressure relief procedures

above.

2. To add material to tank, remove lid

and pour directly into the tank or con-

tainer.

NOTE

If desired, a U.S. or metric 5 gallon

pail of fluid can be placed directly

into the tank.

3. Replace the lid assembly and tighten

thumb screws (6) securely.

4. The air supply to the tank should be

filtered to remove dirt, water and oil

(see Clean Air

™

under Accessories,

page 8). Connect the air supply line to

the tank inlet valve.

5. Connect the material hose to fluid

outlet ball valve (16).

USING BOTTOM OUTLET PORT

The pressure tank has a 1 inch NPT drain

port in the bottom of the tank. Bottom outlet

kits may be connected into the drain port.

Use bottom outlet feature when top outlet is

not desirable. Direct bottom outlet piping to

either one of two holes located in tank skirt.

A dolly to raise the tank off the floor is not

required.

OPERATION

1. Close air inlet valve to tank. Turn handle

on regulator counterclockwise until

spring tension is relieved.

2. Turn on air supply to tank.

3. Open air inlet valve to tank.

4. Open fluid outlet valve.

5. Turn handle on tank pressure regulator

clockwise to pressurize tank. Clockwise

increases material pressure; counter-

clockwise will decrease material pres-

sure. If the pressure tank has no regula-

tor, adjust pressure at the source.

6. Turn on atomization air to spray gun at

source of supply.

7. Test spray. For further instructions, see

spray gun service bulletin SB-2-001.

NOTE

If tank has a hand agitator, agitate

material periodically by turning

crank slowly clockwise.

If an air motor drive is used, start

the agitator by slowly opening the

needle valve. Air motor speed

should be regulated according to

the nature of the material being

agitated. The agitator should be

running continuously while using

the tank.

PREVENTIVE MAINTENANCE

To clean equipment, proceed as follows:

1. Turn off the air supply.

2. Follow pressure relief procedure

on page 3.

3. Turn T-handle adjusting screw on tank

fluid regulator counterclockwise until

no spring pressure is felt.

SERVICE CHECKS

CONDITION CAUSE CORRECTION

A. Air escaping from port on 1. Broken or damaged diaphragm. 1. Replace diaphragm.

regulator cap.

B. Pressure creepage registered 1. Dirty or worn valve seat in 1. Clean or replace valve seat.

on gauge. regulator.

C. Material tends to settle out 1. Not enough agitation of material. 1. Increase agitation.

rapidly.

D. Air leakage at agitator seal. 1. Defective seal assembly. 1. Replace.

E. Paint getting into bearing 1. Paint level in tank too high. 1. Do not fill tank above

assembly of agitator. agitator bearing assembly.

2. Defective agitator shaft seal. 2. Replace.

F. Fluid or air leak at lid gasket. 1. Thumb screw not tight. 1. Tighten.

2. Defective lid gasket. 2. Replace.

G. Air mixing with paint. 1. Fluid tube not sealed to lid. 1. Tighten fluid tube into lid.

2. Excessive agitation. 2. Reduce speed of agitator.

NOTE: Occasionally check pressure gauge. The needle should return to zero with no pressure on the gauge.

4. Loosen thumb screws (6), tip clamp (7)

back, and tip lid (15) to one side of

tank. Do not remove lid from tank.

5. Loosen spray gun air cap retaining

ring about three turns.

6. Turn on air supply.

7. Cup cloth over air cap on the gun and

pull trigger. This will force material

back through the hose, into the tank.

8. Empty and clean tank and parts that

come into contact with material.

Use a solvent compatible with

material being used.

9. Pour solvent into tank.

10. Replace lid and tighten thumb screws

and clamps.

11. Spray until clean solvent appears.

12. Repeat steps 4 through 8.

LUBRICATION

Refer to the service manual provided with

the air motor for lubrication information.

The bearings in the agitator bearing assem-

bly are impregnated with a special non-

gumming oil. Therefore, additional lubrica-

tion is not required.

The agitator shaft seal does not require

lubrication.

SB-21-064-J Page 5

5,10,15 Gallon Stainless Steel Tanks

Exploded View

•Open side of Shaft Seal

(27A) faces downward.

USED ONLY WITH

BOTTOM OUTLET

27A

•

*27B

Refer to Accessories

for Agitator Drives.

36 Used with

no agitation.

For bottom outlet

conversion remove

and discard plug.

Refer to Accessories

for bottom outlet.

NOTE

Use a Teflon based

sealant on all air/fluid

connections.

*Retainer 27B only required in

tank if used for vacuum opera-

tion. Not necessary to replace if

tank is used for pressure only.

PTFE

Page 6SB-21-064-J

PARTS LIST FOR STAINLESS STEEL 5, 10, 15 GALLON TANKS

REF INDIVIDUAL

NO. DESCRIPTION 5 GALLON 10 GALLON 15 GALLON PARTS REQ.

1--- Not Used

2Disposable Tank Liner PTL-406-K20 PTL-410-K8 PT-415-K10 1

3Tank Assembly (includes items 4 through 9) QMS-440 QMS-441 — 1

+4 Clevis Pin — — — 6

•+5 Cotter Pin (1/8 diameter x 1 in. long) — — — 6

+6 Thumb Screw QM-1352 QM-1352 QM-1352 6

+7 Clamp — — — 6

8 Tank, Stainless Steel QMS-505 QMS-510 QMS-515 1

9 Plug — — — 1

10 Stationary Paddle Kit (includes items — QMS-445 QMS-445 1

11 and 12)

11 Stationary Paddle — — — 1

•12 Hex Socket Head Cap Screw — — — 1

(5/16-18 x 1-1/4, Stainless Steel)

13 Fluid Tube (3/8-18 NPT) QMS-10-1 QMS-11-1 QMS-12-1 1

14 Lid Gasket, Santoprene QM-1458-1 QM-1458-1 QM-1458-1 1

15 Tank Lid, Stainless Steel QMS-417 QMS-417 QMS-417 1

16 Ball Valve, 316 Stainless Steel VA-527 VA-527 VA-527 1

17 90°St. Elbow (3/8 x 18 NPT Stainless Steel) SSP-1939 SSP-1939 SSP-1939 1

•18 Plug (3/8-18 NPT Stainless Steel) — — — 1

19 Agitator Assembly (includes items QMS-432 QMS-433 QMS-434 1

20 through 34)

20 Retaining Nut QMS-46 QMS-46 QMS-46 1

21 Thrust Collar Kit (includes items 22 and 23) QMS-447 QMS-447 QMS-447 1

22 Thrust Collar — — — 1

•23 Set Screw (5/16-18 x 3/8) — — — 1

24 Thrust Washer Kit (includes 2 washers) KK-5049 KK-5049 KK-5049 2

25 Bearing Assembly QMS-407 QMS-407 QMS-407 1

26 O-Ring (Kit of 2) SSG-8184-K2 SSG-8184-K2 SSG-8184-K2 1

27 Shaft Seal Kit KK-5042 KK-5042 KK-5042 1

27A Shaft Seal — — — 1

27B Retainer — — — 1

28 Agitator Shaft (5/8" Diameter) QMS-6 QMS-7 QMS-8 1

29 Agitator Paddle Kit (includes items 30 and — — QMS-444 1

31), nylon

30 Agitator Paddle — — — 1

•31 Hex Socket Head Cap Screw — — — 1

(5/16-18 x 1-1/4, Stainless Steel)

32 Agitator Paddle Kit (includes items 33 and QMS-444 QMS-444 QMS-444 1

34), Nylon

33 Agitator Paddle — — — 1

•34 Hex Socket Head Cap Screw — — — 1

(5/16-18 x 1-1/4, Stainless Steel)

35 Not Used — — —

36 Plug QMS-3 QMS-3 QMS-3 1

37 Air Manifold QMG-21 QMG-21 QMG-21 1

38 Air Relief Valve SS-2707 SS-2707 SS-2707 1

•39 Street Elbow (1/4"-18 NPT Brass) — — — 1

40 Safety Valve Assembly, 110 PSI TIA-5110 TIA-5110 TIA-5110 1

Safety Valve Assembly, 40 PSI (for tanks TIA-5040 TIA-5040 TIA-5040 1

with extra sensitive regulation)

• Purchase locally.

+ KK-5014 Clamp, Pin and Screw Kit includes 1 each of Items 4, 5, 6 & 7.

ACCESSORIES

QMS-443 BOTTOM OUTLET CONVERSION KIT

Fittings that allow standard top outlet tank to feed from bottom by

removing plug in bottom port. Kit includes stainless steel shutoff

valve and all stainless steel parts.

Ref. Replacement

No. Part No. Description Qty.

41 ----- Adapter, 3/4" NPT 1

to 3/4-14 NPS(M)

42 ----- Reducer Bushing, 3/4 to 1" s.s. 1

43 ----- Ball Valve, 1 x 1 NPT(f) s.s. 150 PSI 1

44 ----- Pipe Nipple (1" Stainless Steel) 1

45 ----- Street Elbow (1" Stainless Steel) 1

SB-21-064-J Page 7

QMS-4010 EXTRA SENSITIVE REGULATOR KIT

Use with electrostatic spray or other applications requiring ex-

tremely sensitive nonfluctuating low pressure control. Kit

includes one extra sensitive gauge, one extra sensitive regulator,

inlet and outlet shutoff valves, and connection fittings. Refer to

SB-6-131 for regulator service parts.

Ref Replacement

No. Part No. Description Qty.

61 SSP-8217-ZN Swivel Adapter 1

62 VA-542 Valve 2

63 SSP-2629-ZN Tee Male Branch 2

•64 ----- Hex Reducer Bushing 2

(3/8 x 1/4 Galvanized)

65 HAR-501 Extra Sensitive Regulator 1

66 83-1414 Gauge 30 lb. 1

• Purchase locally.

QM-142 HAND CRANK

Mounts on agitator shaft to provide manual

agitation of materials in tank.

QMS-4003 NO REGULATION KIT

Use when fluid pressure in tank is regulated by some other

separate controls. Kit includes air shutoff valve, gauge to read

fluid pressure in tank, and fittings.

Ref Replacement

No. Part No. Description Qty

•46 SSP-35-CD Swivel Coupling 1

•47 ----- Street Tee (1/4") 1

48 83-1290 Gauge 150 lb 1

49 VA-542 Valve 1

• Purchase locally.

QMS-4006 SINGLE REGULATOR KIT (STANDARD)

Provides standard fluid pressure control only. For use when atomi-

zation air is controlled by a separate filter-regulator. Kit includes

pressure regulator with gauge, inlet and outlet shutoff valves, and

connection fittings. Refer to 77-2781 for regulator service parts.

Ref Replacement

No. Part No. Description Qty.

50 SSP-8217-ZN Swivel Adapter 1

51 VA-542 Valve 2

52 HAR-511 Regulator 1

53 83-1290 Gauge 150 lbs. 1

•XX ---- Bushing 3/8 NPT(m) x 1/4 NPT(f) 2

(Supplied/Regulator)

•YY ---- Pipe Plug 1/4 NPT (Supplied/Reg) 1

• Purchase locally.

ACCESSORIES (CONTINUED)

Ref Replacement

No. Part No. Description Qty.

54 VA-542 Valve 2

55 HAR-507 Regulator (Painted) 1

56 83-1355 Gauge, 100 lbs. 1

57 83-4233 D.M. Nipple 1/4 x 3/8 Universal 1

Pipe Threads

58 83-1290 Gauge, 150 lbs. 1

59 HAR-511 Regulator 1

60 SSP-8217-ZN Swivel Adapter 1

•XX ---- Bushing 3/8 NPT(m) x 1/4 NPT(f) 2

(Supplied/Regulator)

•YY ---- Pipe Plug 1/4 NPT (Supplied/Reg) 2

• Purchase locally.

QMS-4007 DUAL REGULATOR KIT (STANDARD)

Provides independent controls for fluid pressure in tank and

atomization air pressure. Kit includes two regulators with gauges,

inlet and outlet shutoff valves, and connection fittings. Refer to

SBBI-6-147 and 77-2781 for regulator service parts.

Page 8SB-21-064-J

ACCESSORIES (CONTINUED)

QMS-436 CONVERSION TO DOUBLE REGULATOR

ASSEMBLY KIT

Adapts to tanks equipped with single regulator to provide

independent pressure control of atomization air and fluid pres-

sure. Converts QMS-4006 single regulator to a QMS-4007 dual

regulator. Refer to SBBI-6-147 for regulator service parts.

Ref Replacement

No. Part No. Description Qty.

67 HAR-507 Regulator 1

68 83-1355 Gauge, 100 lbs. 1

69 83-4233 D.M. Nipple 1/4 x 3/8 1

Universal Pipe Thds.

•YY ---- Pipe Plug 1/4 NPT 1

(Supplied/Regulator)

• Purchase locally.

VS-534 FLUID STRAINER

Primary fluid strainer that attaches between fluid

outlet valve and fluid hose to strain material.

Components made of stainless steel with nylon filter.

Comes standard with 100-mesh screen. For more

information see SB-7-072.

QS-5012 Air Motor Drive

Standard duty 1/2 hp agitator

drive with 15:1 gear reduction.

Operates from 20 to 120 rpm.

Mounts on agitator shaft.

Includes throttling valve, fittings,

and hose for connection to air

supply on tank lid. For further

information see SB-19-087.

31-381 Reciprocating Air Motor Drive

Low air consumption motor

mounts easily on tanks equipped

for material agitation. Slow back

and forth motion ensures proper

agitation. Operates at 10 to 30

cycles per minute. For more

information see part Sheet 77-2788.

DISPOSABLE TANK LINERS

Molded polyethylene tank liners to reduce solvent

waste and tank cleanup time. The liner is made of

tough, durable, leakproof polyethylene and can

be used with all compatible materials.

PTL-406-K20 Kit of 20 tank liners for 5 gal.

PTL-410-K8 Kit of 8 tank liners for 10 gal.

PTL-415-K10 Kit of 10 tank liners for 15 gal.

HFRL-508, HFRL-509 CLEAN AIR™

CONTROL UNITS

These units are designed to remove dirt,

pipe scale and most liquid aerosol.

Includes an automatic drain which expels

liquids which accumulate in the filter bowl.

Inner Diameter .............. 11.75" (298.45mm)

Outer Diameter ........... 15.375" (390.52mm)

Height/Depth ..................... 3.75" (95.25mm)

Case Qty .................................................... 20

PTS-5Gal-K20-200 ..................... 200 micron

(approx. 65 wire mesh)

PTS-5Gal-K20-400 ..................... 400 micron

(approx. 37 wire mesh)

PTS-5Gal-K20-600 ..................... 600 micron

(approx. 28 wire mesh)

PROSPECTORTM PRESSURE TANK STRAINERS

FOR 5, 10, AND 15 GALLON TANKS

Prospector™ strainers are an economical way to remove foreign

material from paint, stain, lacquer and coatings.

WARRANTY

This product is covered by DeVilbiss' 1 Year Limited Warranty.

DeVilbiss Worldwide Sales and Service Listing: www.devilbiss.com

Industrial Finishing

DeVilbiss has authorized distributors throughout the world. For

technical assistance or the distributor nearest you, see listing below.

U.S./Canada Technical Service Office:

195 Internationale Blvd., Glendale Heights, IL 60139

Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)

Toll-Free Fax: 1-800-368-8401

29-3100 SCRUBS®HAND CLEANER TOWELS

Scrubs® are a pre-moistened hand cleaner

towel for painters. No water is needed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DeVilbiss Tankausrüstung Handbücher

DeVilbiss

DeVilbiss PT-500-WB Referenzhandbuch

Beliebte Tankausrüstung Handbücher anderer Marken

ARKSEN

ARKSEN 002-AU-30035/GAS35 Bedienungsanleitung

morse

morse 185G Bedienungsanleitung

IVT

IVT LATENTO XXL Series Benutzerhandbuch

Clayton

Clayton WartHog 603-105W Leitfaden

Vetus

Vetus FTL3808B Kurzanleitung

Astro Pneumatic Tool

Astro Pneumatic Tool PT2-4 Bedienungsanleitung

SII

SII 99800088 Bedienungsanleitung

Gardena

Gardena 4000/5 eco Bedienungsanleitung

CALEFACTIO

CALEFACTIO GMP Bedienungsanleitung

Amtrol

Amtrol FILL-TROL FT-109 Montageanleitung

Graf

Graf 160470 UPone 3 EW, 2000 L Bedienungsanleitung

VIAIR

VIAIR 90011 Bedienungsanleitung

Flexcon

Flexcon FLU/H2PLU Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools Centralpneumatic 66839 Montageanleitung

Regulus

Regulus PS 80 Z Bedienungsanleitung

KIESELMANN

KIESELMANN TDAM 6180 Bedienungsanleitung

Worthington

Worthington Amtrol THERM-X-TROL ST-447C Montageanleitung

Worthington

Worthington AMTROL THERM-X-TROL STL Series Montageanleitung