Devon TREAD 2 Bedienungsanleitung

enGlish

TREAD 2 OPERATING MANUAL

DEVON timepieces are manufactured in California with state-of-the-art technology

and innovative processes. Each one must pass strict quality controls and undergo

rigorous testing throughout the manufacturing process before leaving our factory.

The international warranty of your watch runs for a period of two years from the date

of purchase and covers manufacturing defects that arise during normal usage. For your

convenience, a copy of the user manual and the warranty information are available on

our website, www.devonworks.com.

We invite you to visit the customer portal of our website at www.devonworks.com/

registration in order to register your Tread 2 and validate its warranty. Should your

watch need servicing, please bring it to an authorized DEVON retailer or send an

email to [email protected]. You can also call us at (888)901-0081.

Please accept our warmest welcome to the DEVON brand, and know that we sincerely

appreciate the trust you’ve placed in us.

Kind regards,

Scott Devon

Thank you for purchasing the Tread 2, the second line of timepieces from DEVON.

The Tread 2 was designed, developed and manufactured in California,

USA to the highest standards the laws of physics allow.

WELCOME

DISPLA

minutes

seconds /

battery life

hours

minutes

hours

The Tread 2 case has been tested to prevent water

penetration to a static water depth of 1 atmosphere

(ATM), which is equal to 10 meters or 33 feet.

In order to avoid damage to the watch, please never

operate the crown when it is wet.

WATER RESISTANCEDISPLAY

DISPLAY

minutes

seconds /

battery life

hours

ON / OFF

To turn the Tread 2 ON / OFF:

Push crown button IN momentarily

and RELEASE.

If the Tread 2 is entering into ON

mode, the Time Belts will cycle

to the current time.

If the Tread 2 is entering

into OFF mode, the Time

Belts will advance to the

12:00 position and then

advance the minute

belt to indicate battery

life (see Battery Life

Indicator).

TIME SET

The TIME SET mode of the Tread 2 allows the user

to adjust the time.

To enter TIME SET mode:

While the watch is turned on, push the crown

button IN for greater than 3 seconds until the hour

belt rotates a full revolution to indicate hour TIME

SET mode has been entered.

To adjust hour indicator belt one position:

Push crown lever DOWN and RELEASE.

To adjust hour indication belt multiple positions:

Push crown lever DOWN and HOLD.

Once the hour belt position is correct, push

crown button IN momentarily and RELEASE. The

Tread 2 will rotate the vertical belt a full revolution

to indicate minute TIME SET mode has been

entered.

To adjust minutes indicator belt one position:

Push crown lever DOWN and RELEASE.

To adjust minutes indicator belt multiple positions:

Push crown lever DOWN and HOLD.

To exit TIME SET mode:

Push crown button IN momentarily and RELEASE.

The Tread 2 will advance both the hour and

minute belts a full revolution to indicate the exit

from TIME SET mode.

NOTE: The Tread 2 will resume timekeeping at

zero seconds of the time that was set, therefore

performing this step at the instant a reference clock

hits 0 seconds will insure synchronization.

down push

CHRONOGRAPH

The Tread 2 is equipped with a chronograph

(stopwatch) function. When used as a chronograph,

the horizontal belt represents minutes and the

vertical belt represents seconds.

To enter CHRONOGRAPH Mode:

During normal time display, pull the crown lever

UP momentarily. The horizontal belt will advance

to 12 and the vertical belt will advance to 00.

To start or stop the chronograph:

Push the crown button IN momentarily and

RELEASE. The stopwatch will count seconds

on the vertical belt. Once 60 seconds is reached

the horizontal belt will advance to 1 to track that

a minute has passed. The stopwatch will then

automatically roll over to 1 min again after 10

minutes and 59 seconds has past.

To reset the chronograph:

Push the crown lever DOWN momentarily and

RELEASE.

To exit the chronograph:

Pull the crown lever UP momentarily. The vertical

and horizontal belts will now advance back to the

current hour and minute reading and continue

displaying the current time.

NOTE: Extended use in CHRONOGRAPH mode

causes signiﬁcant drain on the battery

SECONDS MODE

Although the Tread 2 is not equipped with a

second belt, SECONDS mode will allow you to use the

minute belt to indicate the advancing of seconds.

To view the current seconds reading:

During normal time display, push the crown

lever DOWN momentarily. The minute belt will now

advance to the current second reading and begin

ticking.

NOTE: While in this mode you will not be able

to see the current minute reading, however, the

internal clock will continue to track the correct

time.

To exit SECONDS mode:

Push the crown lever DOWN momentarily. The

minute belt will revert back to the current minute

reading.

NOTE: Extended use in SECONDS mode causes

signiﬁcant drain on the battery.

DISPLAY

minutes

seconds /

battery life

hours

BATTERY

BattEry LifE indiCatOr

The Battery Life Indicator is

automatically entered when

the watch is turned OFF.

The minute belt will ad-

vance to a number between

0 and 10 to indicate the

percentage of battery life

remaining when the Tread

2 enters OFF mode. For

instance: if 9 is indicated,

the battery has 90% power

reserve; if the 5 is indicated,

the battery has 50% power

reserve, and so on.

If a low battery is detected by the Tread 2, the

Tread 2 will automatically turn off. This allows the

internal circuitry to retain the correct time before

the battery level is completely depleted. This is an

indication that the Tread 2 should be placed onto

the charging station.

If the Tread 2 is not placed on the charging

station, the battery will continue to drain. The

Tread 2 must be placed in the charging station

within a short period of time to retain the set time.

Once the battery level is brought back to a usable

level, the Tread 2 can be turned on again.

During LOW BATTERY Mode, the Tread 2 may be

turned on again to show the current time, but will

not be allowed to enter into SECONDS mode or

CHRONOGRAPH mode.

The Tread 2 is charged through an inductively

coupled wireless charging system. Plug the Tread 2

box into an electrical receptacle using the included

DC power adapter. To enable charging, place the

Tread 2 on its specialized cradle in the Tread 2 box.

Once the watch is placed in the cradle, the charging

of the internal battery will start.

NOTE: The watch must be fully engaged in the cradle

in order to charge.

As the battery is charged, the battery level indicator in-

creases showing the current level of the battery. Battery

charging will automatically stop when the battery is full.

Once the battery is fully charged, the charging circuitry will

continue to trickle charge the battery to ensure it remains

fully charged. Because of this technology it is not possible

to overcharge the battery of the Tread 2.

The Tread 2 is supplied with 100-240V charger plug.

In some regions, a plug adapter may be required. See

www.devonworks.com for more information on obtaining

the correct adapter for your region.

LOW BattEry indiCatOr

CHARGING

The Tread 2 is equipped with the highest quality

rechargeable battery. With normal use, your

battery should not need to be replaced for many

years. When the battery needs replacement please

use only those that are supplied by an authorized

Devon Works retailer or service center.

CARE AND MAINTENANCE

The Tread 2 is designed and manufactured to

function and retain its beauty and character, however

care should be taken to protect your watch from

extenuating circumstances. Avoid shocks, whether

physical, thermal or other. Avoid exposure to extreme

temperatures (greater than 60°C/140°F, less than

0°C/32°F) or acute temperature changes.

The Tread 2 is manufactured from many

different materials and each material has its own

characteristics and reacts differently to contact

with varying chemicals. While one material

may withstand the effects of many chemicals,

others may not have the same resistance. For

this reason, DEVON recommends avoiding direct

contact with solvents, detergents, perfumes,

cosmetics etc., since they may damage the

strap, case, or gaskets.

The lens on the Devon Tread 2 watch is

manufactured from top quality sapphire. While

sapphire provides an extremely hard surface

that resists scratches, sapphire is brittle and can

crack under extreme forces.

REPLACEMENT

GEnEraL CarE ChEMiCaL rEsistanCE

NOTE: The internal charging cradle within the Tread

2 box can be removed from the box in order to be

used as a stand-alone charger. First, unplug the

power adapter from the back of the box. Then re-

move the charger stand by holding the box with one

hand and pulling up on the cradle with the other.

Once the stand is removed, the velvet insert can

be removed f rom th e stand. Plug the power

adapter back into the stand and use the charging

stand as needed.

CLEaninG

The Tread 2 should never be submerged in any

cleaning solution. Steam cleaning and high-pressure

compressed air should also be avoided when

cleaning the Tread 2. For light cleaning, gently wipe

the surfaces of the Tread 2 with a soft, non-abrasive,

lint-free cloth to remove any loose dirt and dust. For

a heavier cleaning, start by using a jeweler’s blower

to remove loose dust and debris from the surface

and crevices of your watch. Lightly loosen caked-

on debris with a soft brush or other small, soft tool.

Blow away the particles with the jeweler’s blower.

Dampen a non-abrasive cloth, and then wring out

as much water as possible. Rub the cloth gently

over the watch face and case. If a stronger cleaning

agent is needed, isopropyl or rubbing alcohol may be

used. For isopropyl alcohol, use four parts alcohol

to one part water. Dampen a non-abrasive cloth in

the solution, and then wring out as much solution as

possible. Rub the cloth gently over the watch face

and case. For cleaning within the crevices of the

Tread 2, dip a cotton swab in water or the isopropyl

alcohol solution. Rub off as much moisture from

the tip as possible onto a paper towel to prevent it

from collecting on the watch’s surface. Avoid using

any abrasive cleaners on your watch as they cause

scratches. Also avoid the use of soap products as

soap leaves residue.

To clean the wrist-strap, dampen a cloth in clean

water. Rub this over your rubber or leather band

to remove dirt. If the band is rubber, this is all the

cleaning you should do. If your timepiece features a

leather watchband instead of a rubber one, you may

clean it with traditional leather cleaner. Use leather

conditioner on your top-grain (smooth) leather band

occasionally to prevent it from drying. You should do

this once every few months, or when the band feels

dry (necessary frequency will vary). Wipe the leather

band down again with a soft, dry cloth after applying

the conditioner.

Minor scratches are common, especially on watches

that get daily use. The safest way to remove scratches

is always to have the watch serviced by an authorized

Devon retailer or service center.

The Tread 2 should be cleaned and serviced every

2-5 years depending on use and wear. You can send

the watch to your authorized Devon retailer or service

center to have this service performed. Sending your

watch to a Devon service center is the only way to

ensure that the replacement parts are genuine Devon

parts. Your Devon watch will also be returned with

papers documenting the authenticity of the repairs

performed by a Devon service center.

MaintEnanCE and rEpairs

Belts not moving

•Is the watch in Time-Set mode?

If the watch is in Time-Set mode the belts

will be stationary. To exit the mode, press the

crown button in and release. The watch should

begin to keep time.

•Is the watch turned off?

If the watch is displaying 12:00 constantly,

it could be switched off or in Chronograph

mode. Push the crown lever up and release. If

the watch was in Chronograph mode, this will

exit the mode. If no change is made, press the

crown button in and release. If the watch was

off, it will begin its homing routine.

If none of these items resolve the issue, there may

be trouble with the battery or charging systems.

Consult the Battery and Charging section for more

information.

Unresponsive Crown

•Is the watch otherwise functioning?

If the watch is keeping time but the crown switch

is unresponsive, it is likely that something has

malfunctioned in the crown mechanism. The

watch will need to be returned for service and

repair.

•When was the last time the battery was

charged?

The watch continuously monitors the state of

the battery. If the power level drops too low,

the microcontroller will shut down the belts

to conserve power. This allows the watch to

continue to store the correct time until it can

be charged again. Charging the watch for 5-6

hours should return it to a fully charged state.

Consult the Battery and Charging section of

this document for more information.

TROUBLESHOOTING

syMptOMs, CausEs and pOssiBLE sOLutiOns

Battery and Charging

•Battery Life

The capacity of all batteries decreases as they

are used. When new, the Tread 2 should last up

to 2 weeks. For best performance the watch

should be charged as often as possible. There

is no need to allow the battery to become fully

depleted before charging – in fact this can lead

to shorter battery life. Several factors could

contribute to reduced battery performance.

•Is the watch set properly in the cradle?

If the watch is not seated fully in the charging

cradle, the induction coils will not properly

couple and the watch will not charge. If using

a travel charger the box lid must be closed and

latched to secure the watch to the charging

cradle.

•Is the correct power adapter being used?

All the chargers require the same 12 Volt 0.65

Amp adapter.

•How long was the watch on the charger?

Normally it should take about 5-6 hours to

fully charge the Tread 2. Charging overnight

(12 hours) can help ensure the watch is fully

charged. It is most efﬁcient to charge the

watch when it is off.

•Is the watch presently cold?

Lithium-polymer batteries are sensitive to

excessive cold. The effective capacity of the

battery decreases rapidly as temperature

drops below 0°C.

•Is the watch warm or hot when removed from

charger?

Some warming is normal as a result of the

energy dissipated when charging, however

if the watch is exceedingly warm (too hot to

touch) this may indicate a serious problem. The

charger should be immediately unplugged and

the watch and charger returned for testing and

service.

Inhaltsverzeichnis

Sprachen:

Andere Devon Betrachten Handbücher

Devon

Devon Tread 1 Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

Seiko

Seiko N830 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung