DFI EC531-SD Bedienungsanleitung

EC531-SD/EC532-SD Installation Guide

Package Contents

www.d.com

•

1 EC531-SD/EC532-SD system unit

• Mounting screws for SATA drive

•

Mounting screws for Mini PCIe module

Panel

DC-in

DVI-I

(DVI-D signal)

HDMI(2)

USB 3.0 LAN 1 LAN 2

USB 3.0

SATA 2 SATA 1

VGA

COM 1

COM 2

COM 3

Remote

Power on/off

Line-out

Microphone

Expansion slots

DIO COM4 COM5 COM6

Status LED (Orange)

HDD LED (Red)

Power Button

(1)

with LED (Green)

DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the

installation process, please refer to the user's manual.

Notes:

1. Please gently press the power button to avoid possible damages.

2. The HDMI is a DP/HDMI combo port but can only transmit HDMI signals (unless wired as a DP port by

request). Please plug in an HDMI cable with the right orientation and alignment to avoid damage to the

connector. You should feel resistance (due to a pin on the right) if the cable is not inserted correctly.

For detailed instructions, please see a video at https://youtu.be/SUj07rfN5l8.

Align this edge with the

left side of the connector

Angled-corner

(up)

Angled-corner

Aligning side

(left) pin

Installing a 2.5" SATA Drive

1. The SATA drive bay can be easily accessed witout opening the system.

However, the system does not support hot-swapping hard drives; turn off the

system rst. Locate the drive bay on the front panel and open it by releasing

the handle.

2. Slide the HDD into the drive bay. Note that the HDD should be positioned

vertically with the SATA power connector on top of the data connector to

correctly engage with the system's SATA connectors. Then close the drive bay

and lock the handle.

SATA power/data cable

Notes:

1. The slot is desgined to exactly t a 2.5" SATA drive with 7mm thickness; it

cannot t SATA drives with other sizes.

Do not force to close the drive bay if the HDD is not correctly inserted.

SATA drive bay

SATA 2 SATA 1

SATA power

Connecotr

Drive bay handle

Installing a SODIMM

1. The SODIMM sockets are located on the system board. You need to revmove

the system cover first. Before working inside your system, observe the

following precautions:

(1) Make sure the system and all other peripherals connected to it have been

powered off.

(2) Disconnect all power cords and external cables.

2. The 4 mounting screws on the bottom of the system are used to secure the

cover to the chassis. Remove these screws and put them in a safe place for

later use.

3. Remove the supporting bracket to access the SODIMM sockets.

Mounting screw

Supporting bracket

Mounting screw

SODIMM socket

2. Grasp the module by its edges and align the memory’s notch with the

socket’s notch; then insert the memory into the socket at an angle and push

it down until you feel a click.

SODIMM module

Notes:

1. The system supports dual-channel conguration. To enable dual-channel,

populate both SODIMM sockets.

2. The SODIMM sockets can only accept DDR4 memory modules. Please do not

install other types of memory modules.

Installing a Mini PCIe or mSATA Card

The system board is equipped with 2 Mini PCIe slots: one full-size and one half-

size slot. Here we will demonstrate the installation of a full-size Mini PCIe card.

1. Grasp the Mini PCIe card by its edges and align the notch in the connector of

the Mini PCIe card with the notch in the connector on the system board.

Mounting screw

Note:

The system also has a half-size Mini PCIe slot that can accommodate a Mini PCIe

card using mSATA or USB signals.

2. Push down the other end of the card and secure it on the board with the

provided mounting screw.

Installing a PCI or PCIe Expansion Card

Important:

When inserting expansion cards into the system unit, please select a standard card

within 190mm (as shown in the picture below) in order to t expansion slots.

1. PCI and PCIe slots on the riser card inside the system are used to install the

expansion cards. To install the expansion cards, you need to first remove

the slot plates and bracket by uninstalling the mounting screws on the front

chassis.

Slot plate

Mounting screw and bracket

2. Insert the expansion card into a PCI or PCIe slot on the riser card and secure

the bracket in place.

Rear View

PCIe card

Note:

The EC531-SD has one PCIe x16 slot and two PCI slots with the H320-2P1E card,

whereas the EC532-SD has two PCIe x16 slots and one PCI slot with the H320-

1P2E card.

Board Layout and Jumper Settings

www.d.com

USB 3-4 USB 3.0

USB 1-2 USB 3.0

J22

JP2 JP3

J21

HDMI (default)/DP

DVI

System

Fan 2

Front

Panel

SATA Power

DC-in

LAN 2

LAN 1

PCIe x16 (PCIE1)

SPI Flash

BIOS

VGA

Clear CMOS

Data (JP1)

Auto Power-on

Select (JP11)

(JP9)

(JP8) (JP15)

2 10

COM 3

(JP6)

2 10

COM 2

(JP7) (JP14)

2 10

COM 1

LPC

4-pin power

PCIe x4 (PCIE2)

Power

Button

Reset

DDR4_2 SODIMM

DDR4_1 SODIMM

(JP5)

2 2

Status LED

HDD LED

Parallel

DIO Power

DIO

S/PDIF

Front Audio

ECX

SATA 3.0

USB 2.0 13-14

(JP13)

(JP12)

SATA 0 SATA 1

Mini PCIe

mSATA

System

Fan 1

bettery

2 12

USB 2.0

Clear CMOS Data JP1

Normal (default) 1-2 On

Clear CMOS Data 2-3 On

RS232/422/485 Select:

COM 1 (JP5/JP12), COM 2 (JP7/JP14)

RS232 (default) 1-3, 2-4 On

RS422 Full Duplex/RS485 3-5, 4-6 On

RS232/422/485 Select:

COM 1 (JP6), COM 2 (JP13)

RS232 (default) 1-2 On

RS422 Full Duplex 3-4 On

RS485 5-6 On

RS232/Power Select:

COM 1 (JP3), COM 2 (JP2)

R S 2 3 2 ( d e f a u l t ) 1-3 (RI), 2-4 (DCD) On

RS232 with power 3-5 (+5V), 4-6 (+12V) On

Auto Power-on Select JP11

Power-on via Power Button (default) 1-2 On

Power-on via AC Power 2-3 On

Notes:

1. When COM1 RS232/422/485 is selected,

JP5 and JP12 must be set in accordance to JP6.

2. When COM2 RS232/422/485 is selected,

JP7 and JP14 must be set in accordance to JP13.

3. When COM3 RS232/422/485 is selected,

JP8 and JP15 must be set in accordance to JP9.

RS232/422/485 Select:

COM 3 (JP8/JP15)

RS232 (default) 1-3, 2-4 On

RS422 Full Duplex/RS485 3-5, 4-6 On

RS232/422/485 Select: COM 3 (JP9)

RS232 (default) 1-2 On

RS422 Full Duplex 3-4 On

RS485 5-6 On

A45713945

RS232/Power Select:

COM 4 (JP7), COM 5 (JP11)

R S 2 3 2 ( d e f a u l t ) 1-3 (RI), 2-4 (DCD) On

RS232 with power 3-5 (+5V), 4-6 (+12V) On

RS232/422/485 Select:

COM 4 (JP1), COM 5 (JP8)

RS232 (de fault) 1-2 On

RS422 Full Duplex 3-4 On

RS485 5-6 On

RS232/422/485 Select:

COM 4 (JP2/JP3), COM 5 (JP9/JP10)

RS232 (default) 1-3, 2-4 On

RS422 Full Duplex/RS485 3-5, 4-6 On

RS232/422/485 Select:

COM 6 (JP13/JP14)

RS232 (default) 1-3, 2-4 On

RS422 Full Duplex/RS485 3-5, 4-6 On

RS232/422/485 Select:

COM 6 (JP12)

RS232 (default) 1-2 On

RS422 Full Duplex 3-4 On

RS485 5-6 On

(JP7)

(JP2)

(JP3) 1

(JP1) 1

(JP5)

(JP6)

(JP4)

(JP11) 1

(JP9)

(JP10) 1

(JP8) 1

(JP13) 1

(JP14)

(JP12)

DC-in

USB 3.0

USB 7-8

USB 5-6

DIO COM4 COM5 COM6

I/O board

Notes:

1. When COM 4 RS232/422/485 is selected,

JP2 and JP3 must be set in accordance to JP1.

2. When COM 5 RS232/422/485 is selected,

JP9 and JP10 must be set in accordance to JP8.

3. When COM 6 RS232/422/485 is selected,

JP13 and JP14 must be set in accordance to JP12.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI Industrie-PC Handbücher

DFI

DFI EC531-HD Bedienungsanleitung

DFI

DFI VC70B-KU Bedienungsanleitung

DFI

DFI EC510 Bedienungsanleitung

DFI

DFI RM641-SD Bedienungsanleitung

DFI

DFI EC500-ADS Bedienungsanleitung

DFI

DFI EC541-HD Bedienungsanleitung

DFI

DFI EC51 CS Series Bedienungsanleitung

DFI

DFI EC510-KH Bedienungsanleitung

DFI

DFI EC900-FS6 Bedienungsanleitung

DFI

DFI EC70A-KU Bedienungsanleitung

DFI

DFI EC700-BT Bedienungsanleitung

DFI

DFI VC230-BT Bedienungsanleitung

DFI

DFI KS156-AL Bedienungsanleitung

DFI

DFI VC70B-KU Bedienungsanleitung

DFI

DFI EC310 Series Bedienungsanleitung

DFI

DFI EC500-ADS Bedienungsanleitung

DFI

DFI GM831-CSF Bedienungsanleitung

DFI

DFI EC700-BT Bedienungsanleitung

DFI

DFI EC300 Series Bedienungsanleitung

DFI

DFI KS-KH Series Bedienungsanleitung

DFI

DFI EC510-KH Bedienungsanleitung

DFI

DFI EC700-QRB Bedienungsanleitung

DFI

DFI EC500-SD Bedienungsanleitung

DFI

DFI DT200-CS Bedienungsanleitung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung