DFI CA64-TN Bedienungsanleitung

CA64-TC

CA64-TN

Rev. A+

System Board

Users Manual

49800120

Copyri ht

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,

Windows® 98 SE, Windows® ME, Windows® 000 and Windows

NT® 4.0 are registered trademarks of Microsoft Corporation. Intel®,

Pentium® III and CeleronTM are registered trademarks of Intel

Corporation. VIA C3 is a registered trademark of VIA Technologies,

Inc. Award is a registered trademark of Award Software, Inc. Other

trademarks and registered trademarks of products appearing in this

manual are the properties of their respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This users manual contains detailed information about the system

board. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

System Board

This users manual is for the CA64-TC and CA64-TN system

boards. The differences between these boards are shown below.

CA64-TC

(Supports onboard audio)

CA64-TN

Game/MIDI port

Audio jacks

Internal audio

(CD-in and AUX-in)

Front audio (J9)

S3 (Suspend to RAM)

DIMM Standby Power

LED

Table of Contents

Chapter 1 - ntroduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware nstallation

.1 System Board Layout .............................................................................................

. System Memory.............................................................................................................

.3 Frequency Ratio Settings for Processors................................................

.4 Jumper Settings for Selecting the CPUs Front Side Bus...............

.5 Jumper Settings for Clearing CMOS Data..........................................

.6 Ports and Connectors.............................................................................................

Chapter 3 - Award B OS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

ntroduction



Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4. VIA Hardware Monitor............................................................................................

4.3 VIA Service Pack..........................................................................................................

4.4 Audio Drivers ................................................................................................................

4.5 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function ......................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B. Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................



ntroduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA® 8 C694T/8 C686B AGPset

Processor

The system board is equipped with Socket 370. It is also equipped

with a switching voltage regulator that automatically detects 1.050V

to 1.8 5V.

 Pentium® III

- FCPGA 133MHz FSB (1.13GHz-1. 6GHz)

- FCPGA 133MHz FSB (533EB-1GHz)

- FCPGA 100MHz FSB (500E-850E)

 CeleronTM

- FCPGA 100MHz FSB (800MHz-950MHz)

- FCPGA 66MHz FSB (566MHz-700MHz)

 Future VIA C3TM with L cache

System Memory

 Up to 1GB using VCM (Virtual Channel Memory) or PC

SDRAM DIMM (unbuffered or registered)

 Three 168-pin DIMM sockets

 Uses x64 or x7 PC SDRAM, 3.3V

- PC-66 SDRAM DIMM for 66MHz FSB processors

- PC-100 SDRAM DIMM for 100/66MHz FSB processors

- PC-133 SDRAM DIMM for 133MHz FSB processors

 ECC supported (uses x7 PC SDRAM DIMM)

Chapter 1 - Introduction

Note:

If you are using more than one DIMM, make sure you insert

the same type of DIMMs into the DIMM sockets. Using

different types (VCM or PC SDR M) of DIMMs may cause

problems.

ntroduction



Expansion Slots

The system board is equipped with 1 universal AGP slot. AGP is an

interface designed to support high performance 3D graphics cards. It

utilizes a dedicated pipeline to access system memory for texturing,

z-buffering and alpha blending. The universal AGP slot supports AGP

x with up to 533MB/sec. bandwidth and AGP 4x with up to

1066MB/sec. bandwidth for 3D graphics applications. AGP in this

system board will deliver faster and better graphics to your PC.

The system board is also equipped with 4 dedicated PCI slots and

1 shared PCI/ISA slot.

Onboard Audio Features (CA64-TC)

 AC97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 Two NS16C550A-compatible DB-9 serial ports

 One SPP/ECP/EPP DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port (CA64-TC)

 Three audio jacks: line-out, line-in and mic-in (CA64-TC)

Connectors

 One connector for additional external USB ports

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 One ATX power supply connector

 One Wake-On-LAN connector

 One Wake-On-Ring connector

D MMs

MBx64/x7

4MBx64/x7

8MBx64/x7

Memory Size

16MB

3 MB

64MB

D MMs

16MBx64/x7

3 MBx64/x7

64MBx64/x7

Memory Size

1 8MB

56MB

51 MB



ntroduction

 CPU, chassis and AGP fan connectors

 Two internal audio connectors - AUX-in and CD-in (CA64-TC)

 One connector for external line-out and mic-in jacks (CA64-TC)

PC Bus Master DE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33, ATA/66 and ATA/100 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

rDA nterface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the HPSIR and ASKIR

standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J17

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB ports, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

B OS

 Award BIOS, Windows® 95/98/ 000/ME Plug and Play compat-

ible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

 Mbit flash memory

ntroduction



Desktop Management nterface (DM )

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors CPU/system temperature and overheat alarm

 Monitors VCORE/3.3V/5V/1 V/ .5V voltages and failure alarm

 Monitors CPU/chassis fan speed and failure alarm

 Automatic CPU and chassis fans on/off control

 Read back capability that displays temperature, voltage and fan

speed

Refer to the PC Health Status section in chapter 3 and the VIA

Hardware Monitor section in chapter 4 for more information.

1.1.3 ntelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system

enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the Soft-Off By PWRBTN field of the

Power Management Setup, this switch will allow the system to enter

the Soft-Off or Suspend mode.

Dieses Handbuch passt für folgende Modelle

Andere DFI Hauptplatine Handbücher

DFI

DFI LanParty X58-T3eH8 Bedienungsanleitung

DFI

DFI CS331-C246 Bedienungsanleitung

DFI

DFI G486VPC Bedienungsanleitung

DFI

DFI NS70-EC Bedienungsanleitung

DFI

DFI PT630-NRM Bedienungsanleitung

DFI

DFI C51G-ML Bedienungsanleitung

DFI

DFI 915P-TAL Bedienungsanleitung

DFI

DFI PIC-Q170/H110 Bedienungsanleitung

DFI

DFI 945G-TMGF Bedienungsanleitung

DFI

DFI WL051 Bedienungsanleitung

DFI

DFI NB32-SL Bedienungsanleitung

DFI

DFI PS82-BC/BL Bedienungsanleitung

DFI

DFI G586SPB AIO Bedienungsanleitung

DFI

DFI G486-EVB Bedienungsanleitung

DFI

DFI G586IPV Bedienungsanleitung

DFI

DFI SB336-Ni Bedienungsanleitung

DFI

DFI 586ITOX Bedienungsanleitung

DFI

DFI Infinity NF series Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI NF4 SLI INFINITY Bedienungsanleitung

DFI

DFI FS053 Bedienungsanleitung

DFI

DFI CS15-BN Bedienungsanleitung

DFI

DFI AL170 Bedienungsanleitung

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung