DFI CW35-TC Bedienungsanleitung

CW35-TC

Rev. A+

System Board

Users Manual

52600135

Copyri ht

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,

Windows® 98 SE, Windows® ME, Windows® 000 and Windows

NT® 4.0 are registered trademarks of Microsoft Corporation. Intel®,

Pentium® III and CeleronTM are registered trademarks of Intel

Corporation. VIA CyrixIII is a registered trademark of VIA

Technologies, Inc. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC . There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to tr y to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

.1 System Board Layout ..........................................................................................

. System Memory...........................................................................................................

.3 Jumper Settings for Selecting the CPUs Front Side Bus......

.4 Jumper Settings for Clearing CMOS Data........................................

.5 Jumper Settings for Wake-On-Keyboard/Mouse..................................

.6 Jumper Settings for Wake-On-USB Keyboard................................

.7 Ports and Connectors...........................................................................................

Chapter 3 - Award BI S Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 CPU Frequency Control..................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3. Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 Hardware Doctor Utility.........................................................................................

4.3 Intel 10 INF Update Utility for Windows 95/9 /

2000..........................................................................................................................................

4.4 Avance Logic Drivers for Windows............................................................

4.5 Intel 10 Graphics Drivers for Windows..............................................

4.6 Microsoft DirectX .0 Driver.............................................................................

4.7 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C - roubleshooting

C.1 Troubleshooting Checklist....................................................................................

Introduction



1.1 Features and Specifications

1.1.1 Features

Chipset

 Intel® 810E

Processor

The system board is equipped with Socket 370. It is also equipped

with a switching voltage regulator that automatically detects 1.050V

to 1.8 5V.

 Pentium® III

- FCPGA 133MHz FSB (1.13GHz-1. 6GHz on 0.13µ)

- FCPGA 133MHz FSB (533EB-1GHz)

- FCPGA 100MHz FSB (500E-850E)

 CeleronTM

- FCPGA 100MHz FSB (≥1. GHz on 0.13µ)

- FCPGA 100MHz FSB (800MHz-1.1GHz)

- FCPGA 66MHz FSB (566MHz-700MHz)

 VIA CyrixIII processor

System Memory

 16MB to 56MB/51 MB memory using unbuffered DIMMs with

64Mbit/1 8Mbit technology (You must use 3 MBx64 SDRAM

DIMM to support 51 MB memory.)

 Two 168-pin DIMM sockets

 Uses x64 PC-100 SDRAM DIMM, 3.3V

Chapter 1 - Introduction

DIMMs

MBx64

4MBx64

8MBx64

16MBx64

3 MBx64

Memory Size

16MB

3 MB

64MB

1 8MB

56MB



Introduction

Expansion Slots

The system board is equipped with 3 dedicated PCI slots and 1

shared PCI/CNR slot. CNR (Communication and Networking Riser)

is an interface that can support multi-channel audio, V.90 analog

modem, phone-line based networking or 10/100 Ethernet based

networking riser board.

nboard Graphics Features

 Graphics memory

- Shares 1MB of the system memory. This is fixed regardless of

the size of the system memory.

- Uses the Dynamic Video Memory Technology (DVMT) tech-

nology. This freely changes in size because graphics memory is

allocated from the system memory according to current

needs.

- 4MB onboard display cache

 Graphics controller

- 133MHz super AGP performance using 4MB display cache

memory

- 3D hyper pipelined architecture

- D hardware and motion video acceleration

- 9-bit precision hardware motion compensation assistance for

software MPEG decode

- Software DVD at 30fps

 D graphics features

- Resolution: up to 1600x1 00 in 8-bit color at 85Hz refresh

- 64-bit blitter with enhancements

- 64x64x3 color transparent cursor

- Arithmetic stretch blitter

 3D graphics features

- 600K-700K tri/sec sustained

- 55Mpixels/sec

- Flat and Gouraud shading

- MIP mapping with bi-linear and anisotropic filtering

- 16-bit color/Z-buffering

- Discrete/strips/fans

- Anisotropic filtering

- Texture compositing, color keying and chroma keying

Introduction



 Software drivers

- Windows® 95/98/ME

- Windows NT® 4.0 / Windows® 000

nboard Audio Features

 18-bit stereo full-duplex codec with independent variable sam-

pling rate

 High quality differential CD input

 True stereo line level outputs

Compatibility

 Microsoft PC 98 compliant

 VESA Display Power Management Signaling (DPMS)

 VESA DDC B for Plug and Play monitors

 PCI . , CNR 1.0 A type and AC 97 compliant

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One NS16C550A-compatible DB-9 serial por t

 One DB-15 VGA port

 One DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for additional external USB por ts

 One 9-pin connector for 1 external serial port

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 One ATX power supply connector

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU, chassis and second fan connectors



Introduction

 One opened chassis alarm connector

 Three internal audio connectors (AUX-in, CD-in and TAD)

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33, ATA/66 and ATA/100 hard drives

 PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J15

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB ports, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

BI S

 Award BIOS, Windows® 95/98/ 000/ME Plug and Play

compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

Desktop Management Interface (DMI)

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

Introduction



computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors CPU/system temperature and overheat alarm

 Monitors 5VSB/VBAT/VTT(1.5V/1. 5V)/3.3V/5V/±1 V/CPU

voltages and failure alarm

 Monitors the fan speed of the CPU fan, chassis fan and second

fan; and failure alarm

 Automatic chassis and second fans on/off control

 Read back capability that displays temperature, voltage and fan

speed

 Opened chassis alarm

 Supports Intel® processor thermal diode output (real processor

temperature)

Refer to the PC Health Status section in chapter 3 and the

Hardware Doctor section in chapter 4 for more information.

1.1.3 Intelligence

Automatic Chassis/Second Fan ff

The chassis and second fans will automatically turn off once the

system enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the Soft-Off By PWR-BTTN field of

the Power Management Setup, this switch will allow the system to

enter the Soft-Off or Suspend mode.

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI CS15-BN Bedienungsanleitung

DFI

DFI 915P-TAL Bedienungsanleitung

DFI

DFI WL171 Bedienungsanleitung

DFI

DFI LANParty UT ICFX3200-T2R/G Bedienungsanleitung

DFI

DFI AD76 RAID Bedienungsanleitung

DFI

DFI SB331-D Bedienungsanleitung

DFI

DFI G586IPV Bedienungsanleitung

DFI

DFI AD75 Bedienungsanleitung

DFI

DFI G586SPB AIO Bedienungsanleitung

DFI

DFI G586IPB Bedienungsanleitung

DFI

DFI CS65-SC Bedienungsanleitung

DFI

DFI PB50-ZX Bedienungsanleitung

DFI

DFI PT332-DRM Bedienungsanleitung

DFI

DFI CM35-EC Bedienungsanleitung

DFI

DFI ADN171 Bedienungsanleitung

DFI

DFI M8M051 Bedienungsanleitung

DFI

DFI HD632-H81 Bedienungsanleitung

DFI

DFI KT600-AL Bedienungsanleitung

DFI

DFI P4X400-A Bedienungsanleitung

DFI

DFI Infinity NF650I Ultra Bedienungsanleitung

DFI

DFI SD100-H110/Q170 Bedienungsanleitung

DFI

DFI 848P-AL Bedienungsanleitung

DFI

DFI SU171 Bedienungsanleitung

DFI

DFI CS170-Q370/C246 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung