DFI KM400A-MLV Bedienungsanleitung

KM400A-MLV/MV

KM400-MLV/MV

Rev. A+

System Board

User’s Manual

74600328

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect

to the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use

or the results of the use of this document. Further, the manufac-

turer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person

or entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. AMD, AthlonTM XP and AthlonTM are regis-

tered trademarks of Advanced Micro Devices, Inc. VIA®is a regis-

tered trademark of VIA Technologies, Inc. Award is a registered

trademark of Award Software, Inc. Other trademarks and registered

trademarks of products appearing in this manual are the properties

of their respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery manufactur-

er’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can radi-

ate radio frequency energy and, if not installed and used in accord-

ance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should al-

ways be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

System Board

This user’s manual is for the KM400A-MV/MLV and KM400-MV/

MLV system boards. The differences between these boards are

shown below.

KM400A-MV/MLV VIA KM400A

Up to 400MHz FSB

Up to DDR400

“MLV” supports onboard LAN

KM400-MV/MLV VIA KM400

Up to 333MHz FSB

Up to DDR333

“MLV” supports onboard LAN

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.....................................................................

1.2 Package Checklist.........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...............................................................................

2.2 System Memory............................................................................................

2.3 CPU......................................................................................................................

2.4 Jumper Settings..............................................................................................

2.5 Rear Panel I/O Ports..................................................................................

2.6 I/O Connectors.............................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility........................................................................

3.2 Updating the BIOS....................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface..........................................................

4.2 Drivers, Utilities and Software Applications.................................

4.3 6-Channel Audio Output via Software..........................................

4.4 Installation Notes..........................................................................................

101

103

Introduction

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function...............................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................

B.2 Error Messages...............................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist........................................................................

108

104

110

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• KM400A-MV/MLV

- North bridge: VIA®KM400A

- South bridge: VIA®VT8237

• KM400-MV/MLV

- North bridge: VIA®KM400

- South bridge: VIA®VT8237

Processor

The system board is equipped with Socket-A for installing one of

the following supported processors.

• AMD AthlonTM XP 266/333/400MHz FSB (KM400A-MV/MLV)

AMD AthlonTM XP 266/333MHz FSB (KM400-MV/MLV)

• AMD AthlonTM 200/266MHz FSB

Important:

To ensure proper boot up and operation of your system, you

must power-off the system then turn off the power supply’s

switch or unplug the AC power cord prior to replacing the CPU.

System Memory

• Two 184-pin DDR SDRAM DIMM sockets

• KM400A-MV/MLV supports up to 2GB memory using PC1600

(DDR200), PC2100 (DDR266), PC2700 (DDR333) and

PC3200 (DDR400) DDR SDRAM DIMM, 2.5V type

KM400-MV/MLV supports up to PC2700 (DDR333) only.

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

• 1 AGP slot

• 3 PCI slots

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 8x with up to 2.13GB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics applica-

tions. AGP in this system board will deliver faster and better graph-

ics to your PC.

Onboard Graphics Features

• Integrated S3 2D/3D/Video accelerator

- Shares 8MB to 64MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- High quality DVD video playback

• 3D rendering features

- 32-bit true color rendering

- MPEG-2 video textures

• 2D hardware acceleration features

• Motion video architecture

• Software drivers

- Windows®98/2000/ME/XP

Onboard LAN Features (KM400A-MLV/KM400-MLV only)

• Phy fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• PCI master interface

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Introduction

Onboard Audio Features

• Realtek 6-channel codec

• AC’97 2.2 extension compliant codec

• Supports Microsoft®DirectSound / DirectSound 3D

• AC’97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

• S/PDIF-out interface

• 6-channel audio output

S/PDIF-out

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to an

analog format. This prevents the quality of the audio signal from

degrading whenever it is converted to analog. S/PDIF is usually

found on digital audio equipment such as a DAT machine or audio

processing device.The S/PDIF connector on the system board sends

surround sound and 3D audio signal outputs to amplifiers and

speakers and to digital recording devices like CD recorders.

6-channel Audio

The 6-channel audio output function is supported by configuring

the audio software application program.

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification (1.5Gbps interface)

PCI Bus Master IDE Controller

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

Introduction

USB Ports

The system board supports USB 2.0 and USB 1.1. USB 1.1 sup-

ports 12Mb/second bandwidth while USB 2.0 supports 480Mb/sec-

ond bandwidth providing a marked improvement in device transfer

speeds between your computer and a wide range of simultaneously

accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®98/2000/ME/XP Plug and Play compat-

ible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play BIOS.

DMI, along with the appropriately networked software, is designed

to make inventory, maintenance and troubleshooting of computer

systems easier. Refer to chapter 4 for instructions on using the DMI

utility.

Rear Panel I/O Ports (PC 99 color-coded connectors)

• Four USB 2.0/1.1 ports

• One RJ45 LAN port (KM400A-MLV/KM400-MLV only)

• One DB-9 serial port

• One DB-15 VGA port

• One DB-25 parallel port

• One mini-DIN-6 PS/2 mouse port

• One mini-DIN-6 PS/2 keyboard port

• Three audio jacks: line-out, line-in and mic-in

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI LanParty UT RDX200 series Bedienungsanleitung

DFI

DFI AK74-SU Bedienungsanleitung

DFI

DFI CS100 Series Bedienungsanleitung

DFI

DFI LR100-N16 Series Bedienungsanleitung

DFI

DFI EHL171 Bedienungsanleitung

DFI

DFI P4X533-ALE Bedienungsanleitung

DFI

DFI CS65-SC Bedienungsanleitung

DFI

DFI G5C100-N Bedienungsanleitung

DFI

DFI AK75-AL Bedienungsanleitung

DFI

DFI KT600-AL Bedienungsanleitung

DFI

DFI KM266Pro-MLV Bedienungsanleitung

DFI

DFI CA33-SC Bedienungsanleitung

DFI

DFI SB336-Ni Bedienungsanleitung

DFI

DFI 748-AL Bedienungsanleitung

DFI

DFI SD631-C236 Bedienungsanleitung

DFI

DFI G486-EVA Bedienungsanleitung

DFI

DFI PE11-EC Bedienungsanleitung

DFI

DFI K8M800 INFINITY Bedienungsanleitung

DFI

DFI LanParty UT NF4 SLI EXPERT Venus Bedienungsanleitung

DFI

DFI Qseven Q7A-551 Bedienungsanleitung

DFI

DFI G4E620-N Bedienungsanleitung

DFI

DFI G4H875-P Bedienungsanleitung

DFI

DFI G7L332-L Bedienungsanleitung

DFI

DFI CMS100 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung