DFI LT600-DR/D/L Bedienungsanleitung

LT600-DR/D/L

System Board

User’s Manual

935-LT6003-000G

A02820048

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Intel RAID BIOS........................................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Chapter 5 - RAID.................................................................................

Appendix A - NLITE and AHCI Installation Guide ........................

Appendix B - Watchdog Timer ..........................................................

Appendix C - System Error Message ..............................................

Appendix D - Troubleshooting..........................................................

101

124

129

141

143

145

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;A user’s manual

;One IDE cable

;One FDD cable

;Two USB port cables

;Two Serial ATA data cables

;Two Serial ATA power cables

;One “Main Board Utility” CD

;Two RAID/AHCI driver floppy diskettes (LT600-DR only)

;One I/O shield

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Serial ATA

• LGA 775 socket for:

- Intel®CoreTM2 Duo

- Intel®Pentium®D

- Intel®Pentium®4 or Intel®Celeron

- Intel®Celeron D

• Supports Intel Enhanced Memory 64 Technology (EMT64T)

• Supports Enhanced Intel SpeedStep Technology (EIST)

• Supports Intel Hyper-Threading Technology

• Supports 1066/800/533MHz FSB (LT600-DR/D)

Supports 800/533MHz FSB (LT600-L)

• Intel®chipset

- Northbridge: Intel®945G Express chipset (LT600-DR/D)

Intel®945GC Express chipset (LT600-L)

- Southbridge: Intel®ICH7R (LT600-DR)

Intel®ICH7 (LT600-D/L)

• Four 240-pin DDR2 DIMM sockets (LT600-DR/D)

Two 240-pin DDR2 DIMM sockets (LT600-L)

• Supports DDR2 533 and DDR2 667 DIMMs

• Supports dual channel (128-bit wide) memory interface

• Supports up to 4GB system memory (LT600-DR/D)

Supports up to 2GB system memory (LT600-L)

• Supports non-ECC x8 and x16 DIMMs

• Supports up to 1Gb DRAM densities

• Supports unbuffered DIMMs

• 1 PCI Express x16 slot

• 6 PCI slots (LT600-DR/D)

5 PCI slots (LT600-L)

• Integrated Intel Graphics Media Accelerator 950

• Realtek ALC662 5.1-channel High Definition Audio CODEC

•Six channel DAC support 16/20/24-bit PCM format for 5.1

channel audio solution

• Two stereo ADC support 16/20-bit PCM format

• All DAC/ADC support independent 44.1k/48k/96kHz sample

rate

•44.1k/48k/96kHz S/PDIF-out interface

• Two Realtek RTL8111B PCI Express Gigabit controllers (LT600-DR/D)

One Realtek RTL8111B PCI Express Gigabit controller (LT600-L)

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Supports four SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification

• SATA speed up to 3Gb/s

• RAID 0, RAID 1, RAID 0+1 and RAID 5 (LT600-DR only)

Chapter 1 - Introduction

Specifications

Introduction

IDE Interface

Rear Panel I/O

Ports

I/O Connectors

BIOS

Energy Efficient

Design

Damage Free

Intelligence

Temperature

Humidity

PCB

• One IDE connector supports up to two UltraDMA 100Mbps

IDE devices

• Supports PIO IDE transfers up to 16MB/sec

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 1 DB-9 serial port

• 1 DB-15 VGA port

• 2 RJ45 LAN ports (LT600-DR/D)

1 RJ45 LAN port (LT600-L)

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line-out

• 2 connectors for 4 additional external USB 2.0/1.1 ports

• 1 connector for an external COM 2 port

• 1 Digital I/O connector (LT600-DR/D)

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector and 1 S/PDIF-out connector

• 1 connector for IrDA interface

• 4 Serial ATA connectors

• 1 40-pin IDE connector and 1 floppy connector

• 1 24-pin ATX power connector and 1 4-pin 12V power connector

• 1 chassis open connector

• 1 front panel connector

• 3 fan connectors

• Award BIOS

• 8Mbit flash memory

• Supports ACPI specification and OS Directed Power Manage-

ment

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-LAN and Wake-On-Ring

- RTC timer to power-on the system

• System power management supported

• CPU stopped clock control

• Microsoft®/Intel®APM 1.2 compliant

• Soft Power supported - ACPI v2.0 specification

• AC power failure recovery

• Monitors CPU/system/AUX temperature and overheat alarm

• Monitors Vcore/VCC3/VBAT/3VSB/12V/1.5V/1.8V/5V voltages

and failure alarm

• Monitors CPU/2nd/system fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan

speed

• Watchdog timer function

•0

oC to 60oC

• 10% to 90%

• 4 layers, ATX form factor

• 30.5cm (12") x 24.4cm (9.6")

Introduction

S/PDIF

Features

The Watchdog Timer function allows your

application to regularly “clear” the system at

the set time interval. If the system hangs or fails to function, it will

reset at the set time interval so that your system will continue to

operate.

DDR2 is a higher performance DDR technology

whose data transfer rate delivers bandwidth of 4.3

GB per second and beyond. That is twice the speed of the conven-

tional DDR without increasing its power consumption. DDR2

SDRAM modules work at 1.8V supply compared to 2.6V memory

voltage for DDR modules. DDR2 also incorporates new innovations

such as the On-Die Termination (ODT) as well as larger 4-bit pre-

fetch against DDR which fetches 2 bits per clock cycle.

The Intel northbridge chip comes integrated with the

Intel Graphics Media Accelerator 950 delivering ex-

ceptional 3D graphics performance.

The audio jacks at the rear panel will

support 5.1-channel audio only when the

audio utility is configured to support this function. The mic-in at the

rear will be disabled. Use the front audio’s mic-in jack.

S/PDIF is a standard audio file transfer format that

transfers digital audio signals to a device without

having to be converted first to an analog format. This prevents the

quality of the audio signal from degrading whenever it is converted

to analog. S/PDIF is usually found on digital audio equipment such as

a DAT machine or audio processing device.The S/PDIF connector on

the system board sends surround sound and 3D audio signal out-

puts to amplifiers and speakers and to digital recording devices like

CD recorders.

watchdog timer

5.1-channel audio

DDR2

graphics

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI EHL556 Bedienungsanleitung

DFI

DFI LanParty NF3 Ultra-DF Bedienungsanleitung

DFI

DFI KD171 Bedienungsanleitung

DFI

DFI AM33-EC Bedienungsanleitung

DFI

DFI G586VPM/C Bedienungsanleitung

DFI

DFI AL701 Bedienungsanleitung

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Bedienungsanleitung

DFI

DFI BT101 Bedienungsanleitung

DFI

DFI 586ITB Bedienungsanleitung

DFI

DFI LanParty nF4 Bedienungsanleitung

DFI

DFI MB336-NRM Bedienungsanleitung

DFI

DFI LANPARTY DK X58-T3EH6 Bedienungsanleitung

DFI

DFI WL051-BCC-B Bedienungsanleitung

DFI

DFI CS170-Q370 Bedienungsanleitung

DFI

DFI C586HX Bedienungsanleitung

DFI

DFI GIC68-D Bedienungsanleitung

DFI

DFI FS051 Bedienungsanleitung

DFI

DFI SB300-C Bedienungsanleitung

DFI

DFI CMS631-Q470E/H420E Bedienungsanleitung

DFI

DFI WL051-BCC-4305UE Bedienungsanleitung

DFI

DFI SD101-Q170 Bedienungsanleitung

DFI

DFI LanParty PRO875B Bedienungsanleitung

DFI

DFI HD636-H81CS Bedienungsanleitung

DFI

DFI WL053 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung