DFI NP900-B16C Bedienungsanleitung
NP900-B16C
COM Express Board
User’s Manual
935-NP9001-000G
A07800843
Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior writ-
ten permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any ex-
press or implied warranties of merchantability or fitness for any par-
ticular purpose.The user will assume the entire risk of the use or the
results of the use of this document. Further, the manufacturer re-
serves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or en-
tity of such revisions or changes.
© 2008. All Rights Reserved.
Trademarks
Windows®2000, Windows®CE, Windows®XP and Windows®XP
Embedded are registered trademarks of Microsoft Corporation.
Product names or trademarks appearing in this manual are for iden-
tification purpose only and are the properties of the respective own-
ers.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation.This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables must be used in order to comply with
the emission limits.
Table of Contents
About this Manual................................................................................
Warranty.................................................................................................
Static Electricity Precaution................................................................
Safety Measures.....................................................................................
About the Package...............................................................................
Chapter 1 - Introduction....................................................................
Specifications...................................................................................................................................
Features..............................................................................................................................................
Chapter 2 - Hardware Installation....................................................
System Board Layout ..........................................................................................................
Mechanical Diagram................................................................................................................
System Memory..........................................................................................................................
Jumper Settings............................................................................................................................
Connectors......................................................................................................................................
LEDs......................................................................................................................................................
SPI Flash ROM Socket.........................................................................................................
Cooling Options.........................................................................................................................
Installing NP900-B16C onto a Carrier Board..............................................
Chapter 3 - BIOS Setup......................................................................
Award BIOS Setup Utility.................................................................................................
Updating the BIOS..................................................................................................................
Chapter 4 - Supported Softwares.....................................................
Drivers for Windows Vista System..........................................................................
Drivers for Windows XP System..............................................................................
Appendix A - Watchdog Timer.............................................................
5
5
6
6
7
8
8
10
11
11
12
13
16
17
22
24
25
31
36
36
73
75
76
98
118
About this Manual
An electronic file of this manual is included in the CD. To view the
user’s manual in the CD, insert the CD into a CD-ROM drive. The
autorun screen (Main Board Utility CD) will appear. Click “User’s
Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from
misuse of the product, inability to use the product, unauthorized
replacement or alteration of components and product specifica-
tions.
2. The warranty is void if the product has been subjected to physi-
cal abuse, improper installation, modification, accidents or unau-
thorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may
not, under any circumstances, attempt to perform service, adjust-
ments or repairs on the product, whether in or out of warranty.
It must be returned to the purchase point, factory or authorized
service agency for all such work.
4. We will not be liable for any indirect, special, incidental or
consequencial damages to the product that has been modified
or altered.
1
6
Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board,
components or devices even before installing them in your system
unit. Static electrical discharge can damage computer components
without causing any signs of physical damage. You must take extra
care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the board in its anti-static
bag until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of
the components, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connec-
tors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor,
disk drive and other components. Perform the upgrade in-
struction procedures described at an ESD workstation
only. If such a station is not available, you can provide
some ESD protection by wearing an antistatic wrist strap
and attaching it to a metal part of the system chassis. If a
wrist strap is unavailable, establish and maintain contact
with the system chassis throughout any procedures requir-
ing ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.....
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis
cover for installation or servicing. After installation or servicing,
cover the system chassis before plugging the power cord.
1
7
Introduction
About the Package
The package contains the following items. If any of these items are
missing or damaged, please contact your dealer or sales representa-
tive for assistance.
;The system board
;A user’s manual
;One heat sink
;One “Main Board Utility” CD
;One QR (Quick Reference)
The board and accessories in the package may not come similar to
the information listed above. This may differ in accordance to the
sales region or models in which it was sold. For more information
about the standard package in your region, please contact your
dealer or sales representative.
1
8
Introduction
Processor
Chipset
System Memory
BIOS
Graphics
DMI
LAN
Audio
Expansion
Interfaces
• Intel®AtomTM N270 (Diamondville SC) processor
• 1.6GHz core frequency, 1.10V voltage
• 2.5W thermal design power
• 512KB on-die second level cache
• 533-MT/s FSB
• 22x22 mm, 1.0 mm ball pitch and 437 balls FCBGA
• Intel®chipset
- Intel®945GSE Graphics Memory Controller Hub (GMCH)
- Intel®82801GBM I/O Controller Hub (ICH7M)
• One 200-pin SODIMM socket (1.8V)
• Maximum memory supports up to 2GB
• Supports 400MHz and 533MHz DDR2 SDRAM
• SPI interface BIOS (8Mbit)
• 133/166MHz internal graphics core render frequency at 1.05V
core voltage
• One SDVO port (Port B)
- SDVO slot reversal not supported
• Supports 18-bit dual-channel LVDS
• Supports CRT resolutions up to SXGA+
• DMI lane width - x2 only
• DMI lane reversal not supported
• One Realtek RTL8111C PCI Express Gigabit controller
• Supports 10Mbps, 100Mbps and 1Gbps data transmission
• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant
• Supports Azalia AC97 interface
• PCI 2.3 interface (supports 4 PCI bus masters)
• Supports 8 USB ports (USB 1.1/2.0 host controllers)
• Supports 3 PCIE x1 interface
Chapter 1 - Introduction
Specifications
1
9
Introduction
Serial ATA
IDE
Temperature
Humidity
Power
Regulatory
PCB
• SATA interface supports data transfer rate up to 1.5Gb/s
(150MB/s) per port
• Two SATA ports with independent DMA operation supported
on ports 0 and 2
• Two-mode operation supports legacy mode using I/O space or
an AHCI mode using memory space
• SATA and PATA can be used in a combined function mode
(When SATA is used with PATA, AHCI mode is not supported.)
• Bus Master IDE (PATA) controller
• Supports up to two IDE devices
• Ultra ATA 100/66/33
• Operating: 0oC to 60oC
• Operating: 10% to 90%
• Input: 12V, 5VSB, VCC_RTC
• EMC: CE, FCC Part 15 Class B
• Dimensions
- COM Express basic form factor
- 9.5cm (3.74") x 12.5cm (4.9")
• Compliance
- PICMG COM Express R1.0 basic form factor, Type 2
1
10
Introduction
The Watchdog Timer function allows your
application to regularly “clear” the system at
the set time interval. If the system hangs or fails to function, it will
reset at the set time interval so that your system will continue to
operate.
DDR2 is a higher performance DDR technology
whose data transfer rate delivers bandwidth of 4.3
GB per second and beyond. That is twice the speed of the conven-
tional DDR without increasing its power consumption. DDR2
SDRAM modules work at 1.8V supply compared to 2.6V memory
voltage for DDR modules. DDR2 also incorporates new innovations
such as the On-Die Termination (ODT) as well as larger 4-bit pre-
fetch against DDR which fetches 2 bits per clock cycle.
The integrated graphics delivers exceptional 3D
graphics performance.
The Realtek RTL8111C PCI Express Gigabit
controller supports up to 1Gbps data
transmission.
watchdog timer
graphics
Features
DDR2
gigabit lan
Inhaltsverzeichnis
Andere DFI Hauptplatine Handbücher
DFI
DFI NB32-SC Bedienungsanleitung
DFI
DFI CT132-BR Bedienungsanleitung
DFI
DFI 865PE-ML Bedienungsanleitung
DFI
DFI SB300-C Bedienungsanleitung
DFI
DFI LanParty LT P35 Bedienungsanleitung
DFI
DFI PT332-DRM Bedienungsanleitung
DFI
DFI AL102 Bedienungsanleitung
DFI
DFI SB100-NRM Bedienungsanleitung
DFI
DFI AL9A2 Bedienungsanleitung
DFI
DFI P5BV3+/e Bedienungsanleitung
DFI
DFI CMS630-Q470ECRM Bedienungsanleitung
DFI
DFI ADS310-R680E/Q670E Bedienungsanleitung
DFI
DFI NFII ULTRA-A Bedienungsanleitung
DFI
DFI KD631-C236 Bedienungsanleitung
DFI
DFI SD330-H110 Bedienungsanleitung
DFI
DFI LanParty UT nF3 Ultra-D Bedienungsanleitung
DFI
DFI KD171 Bedienungsanleitung
DFI
DFI AK74-TC Bedienungsanleitung
DFI
DFI AD75 Bedienungsanleitung
DFI
DFI G4H875-P Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
