DFI WL171/WL173 Bedienungsanleitung

WL171/WL173

Mini-ITX Industrial Motherboard

User’s Manual

A-569-M-2018

Preliminary

Version

Preliminary

Version

2User's Manual | WL171/WL173

This publication contains information that is protected by copyright. No part of it may be repro-

duced in any form or by any means or used to make any transformation/adaptation without the

prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions or

changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

3User's Manual | WL171/WL173

Table of Contents

Chapter 1 - Introduction................................................................................................................6

Specifications ......................................................................................................................... 6

Features .................................................................................................................................. 7

DDR4................................................................................................................................. 7

Chapter 2 - Hardware Installation................................................................................................8

Board Layout........................................................................................................................... 8

LEDs ........................................................................................................................................ 8

System Memory ..................................................................................................................... 9

Installing the SO-DIMM Module ..................................................................................... 9

Heatsink and Fan .................................................................................................................10

Jumper Settings ...................................................................................................................12

Clear CMOS (JP1) .........................................................................................................12

LCD/Inverter Power Select (JP5) .................................................................................12

Panel Power Select (JP4) .............................................................................................13

Backlight Brightness Select (JP3)................................................................................13

COM1 Power Select ......................................................................................................14

Auto Power-on Select (JP6) .........................................................................................14

Rear I/O Ports.......................................................................................................................15

DC In ...............................................................................................................................15

USB Ports .......................................................................................................................16

Graphics Display............................................................................................................16

RJ45 LAN .......................................................................................................................17

Audio...............................................................................................................................17

Internal I/O Connectors .......................................................................................................18

COM (Serial) Port ..........................................................................................................18

USB Ports .......................................................................................................................18

Front Audio.....................................................................................................................19

SATA (Serial ATA) ..........................................................................................................19

Chassis Intrusion...........................................................................................................20

Cooling Fan Connectors................................................................................................20

Front Panel.....................................................................................................................21

SMBus ............................................................................................................................21

Battery ............................................................................................................................22

Digital I/O .......................................................................................................................22

LVDS Panel.....................................................................................................................23

V-by-One .........................................................................................................................24

Expansion Slots .............................................................................................................25

Installing the M.2 Module .............................................................................................25

LPC .................................................................................................................................26

4User's Manual | WL171/WL173

About this Manual

This manual can be downloaded from the website, or acquired as an electronic file included in

the optional CD/DVD. The manual is subject to change and update without notice, and may be

based on editions that do not resemble your actual products. Please visit our website or con-

tact our sales representatives for the latest editions.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper in-

stallation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in

or out of warranty. It must be returned to the purchase point, factory or authorized ser-

vice agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to

the product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you

are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, con-

tacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or

connectors by their ends.

Safety Measures

• To avoid damage to the system, use the correct AC input voltage range.

• To reduce the risk of electric shock, unplug the power cord before removing the sys-

tem chassis cover for installation or servicing. After installation or servicing, cover the

system chassis before plugging the power cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other

components. Perform the upgrade instruction procedures described at an ESD

workstation only. If such a station is not available, you can provide some ESD pro-

tection by wearing an antistatic wrist strap and attaching it to a metal part of the

system chassis. If a wrist strap is unavailable, establish and maintain contact with

the system chassis throughout any procedures requiring ESD protection.

5User's Manual | WL171/WL173

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• One WL171/WL173 board

• One COM port cable (Length: 250mm, 2*5 pin headers to DB9)

• One Serial ATA data with power cable (Length: 300mm)

• One Heatsink (Height: 25mm)

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance with the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Optional Items

• USB 2.0 cable

• COM cable

• SATA cable

• Heatsink (Height: 32mm)

• I/O Shield

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance with the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

When installing the system board in a new system, you will need at least the following internal

components.

• Memory module

• Storage device such as hard disk drive, CD-ROM, etc.

• Power adaptor

External system peripherals may also be required for navigation and display, including at least

a keyboard, a mouse and a video display monitor.

Chapter 1

INTRODUCTION

User's Manual | WL171/WL173

Chapter 1 - Introduction

XSpecifications

The specifications listed here may be based on editions that do not

resemble your actual products. Please visit the download page at go.dfi.

com/WL17x, or via the QR code to the right for the latest datasheet.

SYSTEM Processor 8th Generation Intel®Core™ Processors, BGA 1528

i7-8665UE, Quad Core, 8M Cache, 1.7GHz (4.4GHz), 15W

i5-8365UE, Quad Core, 6M Cache, 1.6GHz (4.1GHz), 15W

i3-8145UE, Dual Core, 4M Cache, 2.2GHz (3.9GHz), 15W

Celeron®4305UE, Dual Core, 2M Cache, 2.0GHz (2.0GHz), 15W

Memory 2 x 260-pin SODIMM up to 64GB

DDR4 2400MHz/DDR4 2133MHz (for Celeron 4305UE)

BIOS AMI SPI 128Mbit

GRAPHICS Controller Intel®UHD Graphics 620/ Intel®UHD Graphics 610 (for Celeron

4305UE)

Feature OpenGL 4.4, DirectX 12, OpenCL 2.1

HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG,

HEVC/H265, VP8, VP9

HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9

Display 1 x LVDS/V-by-One (Opt.), resolution up to 1920x1200 @ 60Hz

2 x HDMI/DP, resolution up to 4096x2160 @ 30Hz

Triple

Displays

HDMI/DP++ + HDMI/DP++ + LVDS/V-by-One (Opt.)

EXPANSION Interface 1 x PCIe x4 (Gen 3)

1 x M.2 2242/2260/2280 M key (SATA3.0/PCIe x2)

1 x M.2 2230 E key (PCIe x2/USB 2.0)

AUDIO Codec Realtek ALC888S-VD2-GR

ETHERNET Controller 1 x Intel®I210AT PCIe (10/100/1000Mbps)

1 x Intel®I219LM PCIe with iAMT11.6 and vPro

(10/100/1000Mbps) (only Core i7/i5 supports iAMT)

REAR I/O Ethernet 2 x GbE (RJ-45)

USB 4 x USB 3.1 Gen2

Display 2 x HDMI/DP

Audio 1 x Line-out

1 x Mic-in

INTERNAL I/O Serial 1 x RS-232/422/485 (RS-232 w/ power) (2.0mm pitch)

1 x RS-232 (2.0mm pitch)

USB 4 x USB 2.0 (2.0mm pitch)

Display 1 x LVDS Box Header

1 x V-by-One Connector

Audio 1 x S/PDIF

1 x Front Audio Header

SATA 2 x SATA 3.0 (up to 6Gb/s)

2 x SATA Power

RAID 0/1

DIO 1 x 8-bit DIO

LPC 1 x LPC

SMBus 1 x SMBus

WATCHDOG

TIMER

Output &

Interval

System Reset, Programmable via Software from 1 to 255 Sec-

onds

SECURITY TPM TPM 2.0 (Opt.)

POWER Type Single 12V +/-10% DC (WL171)

Wide Range 9~36V (WL173)

Connector DC-in Jack

Right Angle Connector (4-pin) (available upon request)

Straight Type Connector (4-pin) (available upon request)

RTC Battery CR2032 Coin Cell

OS SUPPORT Microsoft/

Linux

Windows 10 IoT Enterprise 64-bit

Debian 8 (with VESA graphic driver)

Fedpra

CentOS 7 (with VESA graphic driver)

Yocto 2.6

Linux

MECHANICAL Humidity Operating: 5 to 90% RH

Dimensions Mini-ITX Form Factor: 170mm (6.7") x 170mm (6.7")

Height PCB: 1.6mm; Top Side: 16.5mm, Bottom Side: 3.5mm

Chapter 1

INTRODUCTION

User's Manual | WL171/WL173

XFeatures

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so that

your system will continue to operate.

DDR4

DDR4 delivers increased system bandwidth and improves performance. The advantages of

DDR4 provide an extended battery life and improve the performance at a lower power than

DDR3/DDR2.

Graphics

The integrated Intel®UHD graphics engine delivers an excellent blend of graphics performance

and features to meet business needs. It provides excellent video and 3D graphics with out-

standing graphics responsiveness. These enhancements deliver the performance and compat-

ibility needed for today’s and tomorrow’s business applications.

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of

up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s.

Gigabit LAN

The Intel®I219LM and Intel®I210AT Gigabit Ethernet Controllers support data transmission at

1Gbps.

Audio

The Realtek ALC888 audio codec provides 7.1 channel High Definition audio output.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-

agement Event) signal. However, if your system is in the Suspend mode, you can power-on the

system only through an IRQ or DMA interrupt.

Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a system from the

S3 (STR - Suspend To RAM) state.

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enables PCs to implement Power Manage-

ment and Plug-and-Play with operating systems that support OS Direct Power Management.

ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM

function.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing

the power button or selecting “Standby” when you shut down Windows®without having to go

through the sometimes tiresome process of closing files, applications and operating system.

This is because the system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The operating ses-

sion will resume exactly where you left off the next time you power-on the system.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

USB

The system board supports the new USB 3.1 Gen 2. It is capable of running at a maximum

transmission speed of up to 10 Gbit/s (1.2 GB/s) and is faster than USB 3.1 Gen 1 (5 Gbit/s, or

625 MB/s), USB 2.0 (480 Mbit/s, or 60 MB/s) and USB 1.1 (12Mb/s). USB 3.1 reduces the time

required for data transmission, reduces power consumption, and is backward compatible with

USB 2.0. It is a marked improvement in device transfer speeds between your computer and a

wide range of simultaneously accessible external Plug and Play peripherals.

RTC Timer

The Real Time Clock (RTC) installed on the system board allows your system to automatically

power-on on the set date and time.

Chapter 2

HARDWARE INSTALLATION

User's Manual | WL171/WL173

Chapter 2 - Hardware Installation

DDR4_2 SODIMM

DDR4_1 SODIMM

39 1

Line Out

Mic In

Important:

Electrostatic discharge (ESD) can damage your board, proces-

sor, disk drives, add-in boards, and other components. Perform

installation procedures at an ESD workstation only. If such a

station is not available, you can provide some ESD protection

by wearing an antistatic wrist strap and attaching it to a metal

part of the system chassis. If a wrist strap is unavailable, es-

tablish and maintain contact with the system chassis through-

out any procedures requiring ESD protection.

Note:

Some of the components are model-specific. Please refer to the specifications for detail.

Important:

When the Standby Power LED lights up, it indicates that there

is power on the system board. Power-off the PC then unplug

the power cord prior to installing any devices. Failure to do

so will cause severe damage to the motherboard and compo-

nents.

XLEDs

Base-T LED (left),

Wireles LED (right)

LVDS/V-by-One

Lock Detect LED

SATA LED

XBoard Layout

DDR4_2 SODIMM

DDR4_1 SODIMM

39 1

Line Out

Mic In

LED3

SATA0

SATA1

LPC

LVDS Inverter Power

USB 7/8 (USB 2.0)

PCIE1 (PCIe x4)

Front Audio

USB 1/2

(USB 3.0/2.0)

USB 3/4

(USB 3.0/2.0)

LAN2

LAN1

HDMI/DP++

DC In

Note

Buzzer

JP1

JP5

JP3

LVDS

V-by-One HS (Optional)

LED4

JP4

Battery

Front Panel

DIO

JP6

SATA Power

M.2 E Key

Chassis Intrusion

COM1

COM2

SPI Flash BIOS

M.2 M Key

LED2

USB 5/6 (USB 2.0)

SMBUS

SYS FAN

CPU FAN DIO Power

LED1

JP2

Intel

BGA 1528

17 18

14 15 19

31 30

3233

Chapter 2

HARDWARE INSTALLATION

User's Manual | WL171/WL173

DDR4_2 SODIMM

DDR4_1 SODIMM

39 1

Line Out

Mic In

• 2 x 260-pin SODIMM up to 64GB

• DDR4 2400MHz (Celeron 4305UE 2133MHz only)

XSystem Memory

Features

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits from the memory channels.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides

better system performance because it doubles the data transfer rate.

Single Channel DIMMs are on the same channel. DIMMs in a channel can be identi-

cal or completely different. However, we highly recommend using

identical DIMMs. Not all slots need to be populated.

Dual Channel DIMMs of the same memory configuration are on different channels.

DDR4_1

DDR4_2

Installing the SO-DIMM Module

Before installing the memory module, please make sure that the following safety cautions are

well-attended.

1. Make sure the PC and all other peripheral devices connected to it has been powered

down.

2. Disconnect all power cords and cables.

3. Locate the SO-DIMM socket on the system board

4. Make sure the notch on memory card is aligned to the key on the socket.

XSystem Memory

Notch

Retention Notch

Key

Socket Top View

DDR4 SO-DIMM

Retention Clip

45°

Step 1

Step 2

Step 3

Chapter 2

HARDWARE INSTALLATION

User's Manual | WL171/WL173

XSystem Memory

XInstalling the SO-DIMM Module

Please follow the steps below to install the memory card into the socket.

Step 1:

Insert the memory card into the

slot while making sure 1) the

notch and the key are aligned,

and 2) the non-connector end

rises approximately 45 degrees

horizontally. Press the card firmly

into the socket while applying and

maintaining even pressure on both

ends.

Step 2:

Press the end of the card far from

the socket down while making

sure the retention notch and the

clip align as indicated by the dot-

ted line in the illustration. If the

retention notch and the clip do not

align, please remove the card and

re-insert it. Press the card all the

way down.

Step 3:

The clips snap automatically and

abruptly to the retention notches

of the card sounding a distinctive

click, and lock the card in place.

Inspect that the clip sits in the

notch. If not, please pull the clips

outward, release and remove the

card, and mount it again.

Notch

Retention Notch

Key

Socket Top View

DDR3 SO-DIMM

Retention Clip

45°

Step 1

Step 2

Step 3

XHeatsink and Fan

DDR4_2 SODIMM

DDR4_1 SODIMM

39 1

Line Out

Mic In

The CPU must be kept cool by using a CPU fan with heatsink. Without sufficient air circulation

across the CPU and heatsink, the CPU will overheat damaging both the CPU and system board.

1. Before you install the fan / heatsink, you must apply a thermal paste onto the top of

the CPU. The thermal paste is usually supplied when you purchase the fan / heatsink

assembly. Do not spread the paste all over the surface. When you later place the heat-

sink on top of the CPU, the compound will disperse evenly.

Some heatsinks come with a patch of pre-applied thermal paste. Do not apply thermal

paste if the fan / heatsink already has a patch of thermal paste on its underside. Peel

the strip that covers the paste before you place the fan / heatsink on top of the CPU.

2. Place the heatsink on top of the CPU. The 4 spring screws around the heatsink, which

are used to secure the heatsink onto the system board, must match the 4 mounting

holes around the socket.

3. Orient the heatsink so that the CPU fan’s cable is nearest the CPU fan connector.

Important:

A boxed Intel®processor already includes the CPU fan and heatsink assembly. If

your CPU was purchased separately, make sure to only use Intel®-certified fan and

heatsink.

Mounting holes

CPU fan connector

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI HR100-CRM Bedienungsanleitung

DFI

DFI AD70-SC Bedienungsanleitung

DFI

DFI PT332-DRM Bedienungsanleitung

DFI

DFI LANPARTY DK X58-T3EH6 Bedienungsanleitung

DFI

DFI AD76 RAID Bedienungsanleitung

DFI

DFI CS100-Q370 Bedienungsanleitung

DFI

DFI CL630-CRM Bedienungsanleitung

DFI

DFI lanparty dk P45 series Bedienungsanleitung

DFI

DFI P2MEX/A Bedienungsanleitung

DFI

DFI LanParty DK 790GX-M2RS Bedienungsanleitung

DFI

DFI PS35-BC Bedienungsanleitung

DFI

DFI 865pe infinity Bedienungsanleitung

DFI

DFI Q7-100 Bedienungsanleitung

DFI

DFI G7B330-B Bedienungsanleitung

DFI

DFI SU256-SCM Bedienungsanleitung

DFI

DFI FS051 Bedienungsanleitung

DFI

DFI CS30-TC Bedienungsanleitung

DFI

DFI AK70 Bedienungsanleitung

DFI

DFI CS332-C246/Q370 Bedienungsanleitung

DFI

DFI G486VPA Bedienungsanleitung

DFI

DFI CA33-SC Bedienungsanleitung

DFI

DFI NB72-SC Bedienungsanleitung

DFI

DFI HU101 Bedienungsanleitung

DFI

DFI P4X533-ALE Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung