DGH MS 2000 Bedienungsanleitung

MS2000

Electronic Steam

Humidifiers

MiniSteam

Residential

Owner’s

Manual

Read and Save

these Instructions

Systems, L.L.C.

Item Page

CONTENTS

Your MiniSteam steam humidifier will consist of:

INSTALLATION

MOUNTING THE HUMIDIFIER

MOUNTING THE STEAM NOZZLE

RUNNING THE STEAM HOSE.

PLUMBING

POWER WIRING

CONTROL WIRING

START UP AND CHECK OUT OF THE SD 2000 HUMIDIFIER

Startup Checklist

Startup Procedures

OPERATING YOUR MINISTEAM HUMIDIFIER

The MiniSteam Controller

The Main Control Board

MAINTENANCE

Cleaning the steam cylinder

Cleaning the fill and drain valves

ALARMS & FAULT CONDITIONS

Other Trouble-Shooting Hints

REPLACEMENT PARTS - BLOWER UNIT

REPLACEMENT PARTS - HUMIDIFIER UNIT

HUMIDIFIER WIRING DIAGRAM

TECHNICAL SPECIFICATIONS

Limited Warranty

All Products manufactured by DGH Systems, L.L.C. are warranted to the original purchaser to be free

from defects in materials and workmanship in the course of normal and reasonable use for a period of 2

years from the date of installation or 2 years and 1 month from the date of shipment, whichever comes first,

so long as the product has been installed and operated in accordance with all appropriate manuals and

wiring diagrams.

Any product or part that is found to be defective will, at the option of DGH Systems, L.L.C. be

replaced or repaired. DGH Systems, L.L.C. reserves the right to inspect any part or installation before

replacing or repairing defective parts. After startup of the product, labor for repairs or replacement of parts is

not covered by this warranty. Replacement of routinely replaceable parts such steam cylinders and gaskets

are not covered by this warranty.

DGH Systems, L.L.C. assumes no liability for consequential or inconsequential damage, or damage

due to negligence or improper use. Under the terms of this warranty, the original purchaser may have certain

legal rights and other rights which may vary from state to state.

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

For duct mounted applications

(Figure 1):

■1 Steam humidifier unit

■1 Duct steam nozzle

■10’ - 7/8” ID steam hose

■2 Steam hose clamps

■10’ - 5/16” ID condensate hose

■1 Condensate hose clamp

■1 HC-101 humidistat

■1 PC-301 air proving switch

■2 Fill cup extenders

■3 Screws and anchors

■1 Fill connector

For room mounted applications

(Figure 2):

■1 Steam humidifier unit with

blower attached

■1 HC-101 humidistat

■3 Screws and anchors

■1 Fill connector

IMPORTANT:

BEFORE beginning

installation:

■Check for shipping damage to

cartons. Mark the shipping waybill

accordingly.

■Open cartons and check for any

hidden damage. Mark the shipping

waybill accordingly.

■Check packing slip to insure all

items have been received. Notify

DGH immediately of any

shortages or damaged parts.

You

must notify DGH within 5

working days of any shortages.

Your

MiniSteam

steam humidifier will consist of:

Figure 1

Figure 2

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

1. Open the carton and carefully

remove the humidifier and

accessories.

2. Open the humidifier, using a flat

blade screwdriver, and remove the

mounting hardware and

accessories.

3. Remove the plastic steam

cylinder by loosening the clamp

on the top left of the cylinder and

lifting the cylinder while twisting it

up out of its base.

a. Disconnect the wires on

top by carefully loosening and

removing the plastic knobs

holding them in place.

Carefully use a pliers if

necessary to loosen the knobs.

CAUTION:

Do not squeeze

the pliers too hard, and turn

counter-clockwise only.

Installation - Mounting the Humidifier

Figure 3

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

4. Locate where you will install

the duct steam nozzle in the duct

(if used), and then decide on a

convenient location for the

humidifier, that will permit the

hoses to be sloped properly.

5. Use the mounting bracket to

mark the wall for drilling. Use a

level to insure the unit will hang

level. (See Figure 4 at right)

CAUTION:

make sure that the

screws will go into wall studs to

support the weight of the

humidifier.

6. If the mounting screws will be

screwed into wood, drill 2 -1/8"

pilot holes for the mounting

bracket. If dry wall, drill 2 -5/16"

holes for the anchors.

(See Figure 5 above)

7. Insert the screw anchors if

needed and then screw in the

mounting screws through the

bracket. The top edge of the

bracket should stand out away

from the wall.

(See Figure 6 above)

Figure 4

Figure 6

Figure 5

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

DIMENSIONS:

A=Clearance in front of

humidifier 36" (72" with blower)

B=Clearance to left side of

humidifier 12"

C=Clearance to right side of

humidifier 12"

D=Clearance to right side of

blower unit 12"

E=Clearance from top of blower

to ceiling 24"

F=Clearance from bottom of

humidifier to floor 12"

IMPORTANT:

Maximum length of

rubber steam hose is 20 feet.

10 feet is supplied with the

humidifier.

9. Remove the mounting bracket

from the back of the humidifier

Mount the humidifier unit as close

to the steam distributor pipe as

possible to minimize condensate.

Mount the humidifier unit below

the steam distributor pipe

whenever possible. Insure that a

slope can be maintained in the

steam hoses. Certain mounting

clearances must be maintained to

allow access for maintenance, and

for steam discharge from the

blower unit:

Figure 8

Figure 7

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

10. Hang the humidifier unit

carefully on the mounting bracket.

(See Figure 9 at right)

11. Secure the bottom of the

humidifier unit to the wall using

the third screw.

(See Figure 10 at right)

Figure 9

Figure 10

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

12. Locate a suitable position for

the steam nozzle per Figure 11

at right.

a. Locate the nozzle at least

18" upstream of any duct

takeoffs or elbows.

b. If the steam nozzle is

installed from the bottom of

the duct, locate it in the center,

and cap off the condensate

outlet nipple.

12. Cut or drill a 2-1/2" hole in the

side of the duct to fit the steam

nozzle.

13. Apply silicone caulk to the

faceplate of the steam nozzle and

insert it into the duct with the 5/16"

outlet nipple at the bottom, as

shown in Figure 12 above.

14. Attach the steam nozzle to the

duct using #10 by 1/2" drill point

sheet metal screws (not included).

Be sure the nozzle is mounted

level, with the 5/16" outlet nipple at

the bottom.

(See Figure 13 above)

Installation - Mounting the Steam Nozzle

Figure 12

Figure 11 Figure 13

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

CAUTION:

90% of all

operational problems with the

MiniSteam humidifier can be

traced to improper installation of

the steam hose. It is very critical

that steam be allowed to flow

freely from the humidifier unit to

the steam nozzle, and that

condensate can flow back.

■A 20% slope must be

maintained from the humidifier

unit to the steam nozzle. That

means the hose must slope up

2 1/2" for every foot of the

length of the steam hose.

■There must be NO sags,

kinks or low areas in the steam

hose that can collect

condensate or otherwise

restrict the steam flow.

■Copper tubing may be used

in place of the steam hose, but

it must be a minimum of 7/8"

ID and must be insulated.

DO NOT REDUCE THE SIZE

OF THE STEAM HOSE OR

PIPE.

16. Slip the end of the 7/8" ID

rubber steam hose over steam

nozzle inlet nipple and secure it

with the stainless steel hose clamp

supplied.

(See Figure 15 at right)

17. Slip the 5/16" ID condensate

hose over the steam nozzle

condensate outlet nipple and

secure it with the plastic hose

clamp supplied.

(See Figure 16 at right)

Installation - Running the Steam Hose

Figure 14

Figure 15

Figure 16

Systems, L.L.C.

MS2000

MiniSteam Residential

Owner’s Manual

18. Bring the end of the steam

hose through the hole in the top of

the humidifier cabinet and slip the

end over the steam cylinder outlet.

Secure the hose using the stainless

the steel hose clamp supplied.

(See Figure 17 at right)

18. Reinstall the steam cylinder

into the humidifier unit by pressing

it down into the O-ring fitting at

the bottom, and then securing all

wires.

CAUTION:

Loose electrical

connections could cause fire, so

make sure all fittings are tight.

(See Figure 18 above)

20. Bring the end of the

condensate hose through the

smaller hole in the top of the

humidifier cabinet and cut it so it

ends in the drain pan of the

humidifier.

(See Figure 19 above)

Figure 17

Figure 18

Figure 19

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Luftbefeuchter Handbücher anderer Marken

Boneco

Boneco H300 Bedienungsanleitung

Bionaire

Bionaire CM1 Handbuch

Air-O-Swiss

Air-O-Swiss AOS 7131 Handbuch

KING

KING K 5002 Rainbow Bedienungsanleitung

Crane

Crane EE-6902 Bedienungsanleitung

Glaziar

Glaziar Ness Bedienungsanleitung

Philips

Philips DreamStation Go Abmessungen

Honeywell

Honeywell MISTMATE HUL520BC Bedienungsanleitung

Stadler Form

Stadler Form Hera Bedienungsanleitung

Hunter

Hunter 31206 Bedienungsanleitung

TaoTronics

TaoTronics TT-AH004 Bedienungsanleitung

adorini

adorini Cigar Heaven Bedienungsanleitung

Lanaform

Lanaform Aroma Bedienungsanleitung

Aprilaire

Aprilaire 800 Series Bedienungsanleitung

Pyle

Pyle SereneLife PHUMDIF8 Bedienungsanleitung

Trotec

Trotec B 200 Bedienungsanleitung

Pure Humidifier

Pure Humidifier EC Series Bedienungsanleitung

Crane

Crane EE-864 Bedienungsanleitung