Dickinson Caribbean Bedienungsanleitung

Dickinson Marine

www.dickinsonmarine.com

info@dickinsonmarine.com

CARIBBEAN / MEDITERRANEAN

Propane Galley Range

INSTALLATION – USE AND CARE MANUAL

This manual MUST be read carefully

DICKINSON RESERVES THE RIGHT TO CHANGE PRODUCTS OR DOCUMENTS AT ANY TIME

QUALITY INSPECTED BY -

Doug & Don

Form#7.2-23 Issue#1 Sept. 14, 2011

CONTENTS

Warnings and Disclosures pg - 3

Stove Dimensions pg - 6

Product Features pg - 7

Burners and Valves pg - 09

Fuel Supply Instructions pg - 10

Fuel Locker Diagram pg - 11

Fuel System Testing pg - 12

Gimbaled Instructions pg - 13

Gimbaled Diagram pg - 14

Built-In Diagram pg - 15

Oven Cooking pg - 18

Care and Cleaning pg - 18

Troubleshooting pg - 20

Part Replacements pg - 20

Limited Warranty pg - 21

Warranty Form pg - 22

PACKING LIST

INSTRUCTION MANUAL

SNAP IN GRILL SECTION

POT HOLDER SEARAIL

POT HOLDERS (2)

CUTTING BOARD

OVEN RACK

PROPANE LOCKER & STOVE WARNING PLATE

TIE DOWN BRACKET

2 X 9V BATTERIES

WARNING!

THIS IS A LOW PRESSURE

PROPANE GAS APPLIANCE.

YOU MUST HAVE A

SEPARATE 11” W/C

(30 mbar)LOW PRESSURE

REGULATOR INSTALLED

CORRECTLY OR

OPERATION WILL

RESULT IN A

DANGEROUS FIRE AND

WILL DAMAGE YOUR

UNIT.

**PLEASE READ YOUR INSTRUCTION MANUAL

BEFORE USE OF THIS APPLIANCE**

Keep your proof of purchase and product serial number for warranty

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result causing property

damage, personal injury, or loss of life.

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch..

• Shut off main supply tank, and call the fire department if the boat has filled with gas.

IMPORTANT

Safety is everyone’s responsibility. Your Dickinson product is designed

and constructed to give you many years of safe use. The operation will

be further enhanced if proper care and judgment are exercised in the

use and maintenance of the appliance.

THIS APPLIANCE IS DESIGNED FOR LOW PRESSURE

PROPANE ONLY, AND MUST HAVE AN 11”WC (30mbar) LOW

PRESSURE REGULATOR

IMPORTANT:

Read this owner’s manual carefully and completely before trying to

assemble, operate, or service this appliance. Improper use of this gas

appliance can cause serious injury or death from burns, fire, explosion,

carbon monoxide poisoning and oxygen depletion. For assistance or

additional information consult a qualified installer, service agency, or your

gas supplier.

TEST ALL PROPANE LINES AND CONNECTIONS FOR LEAKS

WITH A SOAPY WATER SOLUTION. DO NOT FLAME TEST FOR

LEAKS.

LPG is heavier than air and if allowed will settle in lower areas

resulting in a potential explosion.

CLOSE THE LPG CYLINDER VALVE IN THE EVENT OF AN

EMERGENCY

WARNING:

•DO NOT install this appliance in spaces containing internal combustion engines,

their fuel tanks, or joints and fittings of their fuel systems.

•USE ONLY approved materials, hose, regulators and fittings to install.

10ft Hose – ULC Type I CGA St 8.1 – Dickinson Prt# 19-100-10

20ft Hose – ULC Type I CGA St 8.1 – Dickinson Prt# 19-100-20

Propane Low Pressure Regulator UL/C.G.A – Dickinson Prt# 19-151

•DO NOT store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

•INSTALLATION must conform with local codes or in the absence of codes, with

current National Fuel Gas Code, ANSI Z223.1 or current CAN/CGA B149,

Installation Codes.

•MANUFACTURED OR MOBILE HOME OEM installation must conform to

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280,

or, when not applicable, the Standard for Fire Safety Criteria for Manufactured

Home Installation Sites and Communities, ANSI/NFPA 501A,(USA) or Mobile

Homes Standard, CAN/CSA-Z240 MH Series, in Canada

•MAIN GAS VALVE must be disconnected from gas supply system during any

pressure test of the system at pressures greater than ½ psi (3.5 kPa)

IMPORTANT:

Save this manual for future reference.

WHAT TO DO

1. Begin by ensuring proper installation and verify that the appliance has been connected to 11”

WC low pressure propane.

Be familiar with the location of the gas shut-off.

If you smell gas, do not use the appliance. Immediately turn off the gas supply at the shut-off

valve.

2. Make sure you have a 3” fresh air vent, or an open window before operating the stove.

3. Use this appliance only for its intended purpose as described in the manual.

4. Never let clothing or other flammable materials come in contact with the

burners while in operation.

5. When cooking, set the burner controls so that the flame heats only the bottom of the pot and

does not lick at the sides of the pot.

6. Always turn pot handles to the side or back of the appliance. Do not turn handles towards the

front where they are easily hit. Handles should not extend over adjacent burners.

7. Always check the position of the control knobs to make sure the appliance is off when you are

finished cooking.

8. Always light each burner prior to placing a pot on the burner grate. Also, turn the control

knob to the “off” position before removing a pot from the burner grate

9. Wait until the appliance has cooled before cleaning.

10. Always keep the appliance surface clean and dry.

11. Affix the Galley Range Warning / Instruction plate by the stove for easy reading.

WHAT NOT TO DO

1. DANGER-Never use the appliance to warm or heat the room.

2. When using the appliance do not touch the grate, burner caps, burner bases or any parts in

proximity to the flame.

3. Do not leave children alone or unattended in the area where the appliance is in use.

4. Do not use water on grease fires.

5. Never leave the appliance unattended when in use.

6. Do not use oversized pots or pans. See section on ‘burners’.

7. Do not use abrasive or caustic cleaners or detergents on this appliance.

8. Keep appliance area clear and free from combustible material.

MEDITERRANEAN & CARIBBEAN DIMENSIONS

* Tie Down Bar – This is the 1/8

aluminum piece that is appox. 10” long *see pic below. The tie down

bar is to be fastened in your stoves cut out so that the bottom panel housing the battery boxes will slide into

it thus preventing your stove from tilting forward as the boat lists. The two screws in the front of this panel

will prevent the unit from sliding forward but will not prevent the stove from tilting and bending the plate.

PRODUCT FEATURES

Your two-burner or three-burner propane stove contains many unique features. Please read this section

carefully as it identifies the most important.

COOKING GRATE

The cooking grate is designed to snap into place to ensure that it is level and to limit vibration.

IMPORTANT NOTE – The stainless grate and burner tops are exposed to extreme temperatures in a matter

of seconds. In addition, pots are slid over them, and spills introduce foods with high acidity to all of the

surfaces and components. These severe operating conditions will cause an inevitable change in the

appearance of the surfaces and components. Do not place pots directly on the burners as they are not made

to hold the weight, so you must use the cooker with the grate in place.

POT HOLDERS AND RAIL

There is a set of potholders and a potholder rail standard with your appliance. The rail is attached by

inserting the legs into the grate and tightening the brass thumbscrews. The grate can be removed and

turned to position the sea rail at the back or front as required. The potholders are then slipped over this rail

and moved to fit the size of pot or pan by squeezing the end legs so they can slide back and forth. Should

the potholders become loose simply spread the legs a little and they will again become secure. It is

recommended that the potholders be used when any boat motion is anticipated.

CUTTING BOARD

The board is used to provide a flat finished surface at counter top level. It also provides a useful cutting-

board feature that can be used in place or elsewhere

WARNING:

WHEN USING OVEN , REMOVE CUTTING BOARD TO ALLOW PROPER

VENTILATION FOR OVEN BURNER. THE OVEN VENTS THROUGH THE SIDES

OF THE COOKING AREA, AND MUST BE FREE OF OBSTRUCTION.

CUTTING BOARD LEVELLING FEATURE

At the four outside corners of the cooking grate there are small tapped holes. By installing 4 – 8-32 screws

into the tapped holes, with the screw head up, the cutting board can be leveled. It is advisable to tighten the

levelers with a nut on the underside to secure them in place

BURNERS

The top surfaces of the burner caps are porcelain enameled to prevent oxidation (rusting) and to provide an

attractive finish.

Triple Burner

These burners are CGA/AGA approved

FLAME DISPERSION

The burner ring spreads the flame evenly around the burner perimeter. This burner assembly must be

seated properly into the base to produce the desired flame configuration.

FLAME CLEARANCE AND POT SIZES

Space is always at a premium on a boat and the Dickinson Propane Stoves give you the most versatility

and the most powerful burners available in a marine cooktop format. For your safety and for good

maintenance of the appliance, use the appropriate size pots for the right and left burners. On the left, a pot

with a 10 inch base is appropriate. On the right hand side it is best not to use pots or pans with bottoms

greater than 6 inches in diameter.

BURNER SAFETY FLAME-OUT

Thermocouple

Each burner is equipped with a thermo-couple safety sensor. Should the

flame accidentally be extinguished the sensor will automatically turn-off the

gas supply to the burner. In addition, should the burner not ignite on start-up

the gas will not continue to flow to the burner when the control knob is

released.

NOTE:

The thermocouple may need to be wiped off occasionally to keep

flame lit.

BURNER IGNITER AND IGNITER BOX

The burner igniter is located on each burner and is activated by a battery generator.

(Batteries Included – 2 x 9v) The igniter box is located at the bottom of the appliance, below the oven.

To replace the batteries, you will need to unscrew the two bolts, holding the front panel/door onto the oven.

Once unscrewed, simply open the oven door as usual, except now it will come right off the stove.

Now simply unscrew the large black plastic knob on the battery holder.

These knobs contain 9V batteries. When replacing with new batteries, just make sure the battery leads

faces up in the knob. Positioning (as in positive and negative) doesn’t matter. Just as long as the battery

leads slide in first when replacing the knob onto the box.

Battery must face up,

when replacing.

Igniter / Battery Box

GAS CONTROL VALVES

This appliance is equipped with CGA/AGA approved quality gas valves that

offer both electronic ignition and thermocouple flameout safety features. These

valves have been calibrated for use with the burners to produce the required BTU

heat output and flame quality at all settings. The low heat settings on the cooktop

burners are adjustable by removing the knob from the gas valve and placing a

very small flat head screw driver down the center of the shaft. A quarter turn in

either direction will raise or lower the flames in the low position only. (The low

heat settings on the oven control burners are adjustable by removing the knob

from the gas valve and placing a very small flat head screw driver down the shaft

off to the right. A quarter turn in either direction will raise or lower the flames in

the low position only.)

NOTE: The gas valves may seize if they are not used for

a long period of time in the harsh marine environment.

For this reason it is advisable to rotate the gas valves

periodically, a few times over this period.

THE STOVE OPERATES ONLY ON LOW PRESSURE LPG GAS

(11"w/c)(30mbar)

It is recommended that this appliance have a dedicated gas line and

must

have a low-pressure regulator

installed. (11” WC)(30mbar) (Dickinson Part No 19-151)

Connect the gas line to the 3/8" flare connector of the cook top with copper or an approved hose. During

this procedure some particles may get into the fuel line. These could block or restrict the burner orifices.

BLOW OUT FUEL LINE PRIOR TO ATTACHING TO THE PROPANE SUPPLY AND THE

APPLIANCE OR TAPE OVER THE FITTING WHEN INSTALLING THE FUEL LINE SO NO

DEBRIS WILL ENTER.

LPG System Installation

**In some cases the solenoid valve is installed on the low pressure side of the system (i.e. after the

LPG regulator) See solenoid manufactures’ instruction for proper installation.

1. Starting from the propane tank itself, the fuel line attachments should occupy the following

positions: (a) the tank shut-off valve, (b) the solenoid valve, (c) the pressure gauge, (d) the

regulator, and (e) the range itself.

2. If you’ve chosen the gimbaled installation option, the gas supply line should be a flexible fire-

resistant hose, UL/CGA approved for use with propane systems, 3/8” 10mm forged female flare

nut machine crimped on each end.

If your range is a built-in style, you should use either soft copper tubing or a UL/CGA approved

gas hose with a 3/8” (10mm) forged female flare nuts machine crimped onto each end.

Because every connection is a potential leak, the fuel line should be one continuous length of hose

or tubing. Do not make a “T” off the fuel line between an existing appliance and the gas cylinder

to feed another appliance. (You may install a “T” only within the fuel tanks enclosure (propane

locker).

Be sure not to kink the hose or piping connecting the regulator with the range by bending it too

sharply during installation – remember that the pressure (North American) on the downstream side

of the regulator is less than 0.433 psi (28mbar)

3. Protect the hose against vibration and damage by securing it tightly to bulkheads and hull side

with non-corrosive ties or clamps which will not cut, abrade or pinch it.

4. Fuel lines must be protected by close-fitting grommets and sealants where they pass through decks

or bulkheads, and the passage must be made vapor-tight. They should be installed so that they are

readily accessible to inspection.

TYPICAL LPG ON-BOARD SYSTEM

Andere Handbücher für Caribbean

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dickinson Reichweite Handbücher

Dickinson

Dickinson Caribbean Technisches Datenblatt

Beliebte Reichweite Handbücher anderer Marken

Samsung

Samsung FCQ321HTUW Bedienungsanleitung

Kenmore

Kenmore 790.45712 Bedienungsanleitung

Wolf

Wolf CHR CHSSR Bedienungsanleitung

Smeg

Smeg Built-in Microwave Oven Bedienungsanleitung

Zanussi

Zanussi ZCG054G Bedienungsanleitung

Whirlpool

Whirlpool 8575985-W Stücklistenhandbuch

Frigidaire

Frigidaire 316000635 Bedienungsanleitung

GE JCSS630 Bedienungsanleitung

Samsung

Samsung NX58M9960P series Bedienungsanleitung

Hotpoint

Hotpoint RB524R Installationsanleitung

Whirlpool

Whirlpool Roper FGP305KW3 Bedienungsanleitung

Amana

Amana ART6610 SERIES Bedienungsanleitung

Maytag

Maytag MERH770WB Bedienungsanleitung

Fulgor Milano

Fulgor Milano SOFIA Bedienungsanleitung

Premier

Premier EF-4358GH Bedienungsanleitung

Kenmore

Kenmore 790.9010 Series Bedienungsanleitung

KitchenAid

KitchenAid KESC300 Bedienungsanleitung

Frigidaire

Frigidaire FFEF3012LS Benutzerhandbuch