Digi-Code 5010 Bedienungsanleitung

Installation Instructions

Garage Door Opener Radio Controls

Model 5010 (300 mHz) \ 5012 (310 mHz) Single Button Transmitters

Model 5020 (300 mHz) \ 5022 (310 mHz) Dual Button Transmitters

Model 5190-01 (300 mHz) \ 5190-02 (310 mHz) Receivers

WARNING:

•• Disconnect operator power before any installation or repair

•• Always wear safety glasses

Your Digi-Code radio controls are designed specifically to remotely control a garage

door opener from within an automobile and to give years of trouble free service without

adjustment. Because all radio controls are set with the even numbered switches in the

“ON” position when they leave the factory, it is recommended that a different code

be selected and set at the time of installation. Please refer to the “Setting the Code

Switch” section for instructions. The radio frequency (RF) portion of the controls,

however, are tuned to standard frequencies and are thoroughly tested at the factory. This

permits the addition or replacement of either the transmitter or the receiver by specifying

the Model number and the RF frequency designated on the identification label. RF

adjustments are not needed nor should any be attempted.

RECEIVER INSTALLATION

The receiver is designed to mount directly to the operator. It can be remotely installed if

the operator terminal strip is not accessible, or if the power for the receiver is not

obtainable from the operator. To direct mount the receiver, simply loosen the terminal

screws on the operator and insert the two-way lugs from the receiver under the screw

heads along the wall button wires, and tighten the screws ( See Figure #1)

Place the antenna (a 10 inch black wire ) in a vertical position as far from any metal as

possible.

For remote installation the receiver may be mounted near the operator head on a joist or

the ceiling by using the mounting tab. Order Model 5192-06 adapter, which permits

connection between the operator terminal and the two-way lugs on the receiver.

Slip on connectors at one end of the adapter connect to the flat side of each spade lug on

the receiver, and the spade connectors at the other end connect to the operator terminal.

Connect wires as follows:

(a) White wire to terminal “1” or “24v”

(b) Black wire to terminal “2” or “Relay”

(d) Connect push button wires to terminal “1” and “2” (See Figure #2)

Where power for the radio receiver is not available from the operator order a Model

5192-01 power transformer adapter for connection between the operator and the remote

receiver.

SETTING THE ( “RECEIVER” ) CODE SWITCH - TO WORK WITH MODEL

5010 AND MODEL 5012 SINGLE BUTTON TRANSMITTERS

Use your finger to slide the “code switch hatch” from the receiver for access to the code

switch. On the transmitter the entire front lower half of the case ( “ the battery hatch” ) is

removeable. Use a coin or the curved end of the visor clip to disengage the lower half of

the transmitter front. This will expose both the code switch and the battery compartment

(See Figure #3).

Model – 5010 (300mHz) or 5012 (310mHz)

Set both code switches to the code of your choice, being sure both are set the same

since a different setting of just one switch will prevent operation. The digital code is

determined by the position of the 10 small switches numbered 1 through 10 located in the

receiver and the transmitter. Any combination of “on” or “off” positions can be selected

by using a pencil or a pen. (Note: The switches are in the “on” position when the switch

is depressed toward the number.) See Figure #3 above.

Once the codes have been set, check operation and reinsert the hatches.

SETTING THE ( “RECEIVER” ) CODE SWITCHES - TO WORK WITH

MODEL 5020 AND MODEL 5022 DUAL BUTTON TRANSMITTERS

Use your finger to slide the “code switch hatch” from the receiver for access to the code

switch. On the transmitter the entire front lower half of the case ( “ the battery hatch” ) is

removeable. Use a coin or the curved end of the visor clip to disengage the lower half of

the transmitter front. This will expose both the code switch and the battery compartment.

See Figure #3 (Receiver) above and Figure #4 (Dual Button Transmitter) below.

Figure #4

Model – 5020 (300mHz) or 5022 (310mHz)

Before setting the receiver code switches, you will need to set the transmitter code switch

on your model 5020 or 5022. We strongly suggest that you change the code from the

factory setting to provide security for your own system, and to eliminate interference with

neighboring systems.

SETTING THE TRANSMITTER CODE SWITCH – MODEL’S 5020 & 5022

On the transmitter the entire front lower half of the case ( “ the battery hatch” ) is

removeable. Use a coin or the curved end of the visor clip to disengage the lower half of

the transmitter front. This will expose both the code switch and the battery compartment

Once you have done this, locate the code switch and set code switch positions 1 through

9 to your personal code scheme ( THE 10TH POSITION SWITCH MUST BE SET IN

THE CLOSED POSITION “ON” ). We strongly urge that several coding schemes be

avoided: ALL ON; 2,4,6,8,10, ON. These positions are similar to our or other

manufacturers test positions, or are frequently used.

SETTING RECEIVER #1 (WORKS WITH LEFT BUTTON ON TRANSMITTER)

Use your finger to slide the “code switch hatch” from the receiver for access to the code

switch. Set the receiver code switch positions 1 through 9 to match the transmitter code

switch. Then make sure that the 10th position switch on receiver #1 is set in the

closed position “ON”. The left button on the transmitter should now operate this

receiver.

Once the codes have been set, check operation and reinsert the hatches.

SETTING RECEIVER #2 (WORKS WITH RIGHT BUTTON ON TRANSMITTER)

Use your finger to slide the “code switch hatch” from the receiver for access to the code

switch. Set the receiver code switch positions 1 through 9 to match the transmitter code

switch. Then make sure that the 10th position switch on receiver #1 is set in the open

position “OFF”. The right button on the transmitter should now operate this receiver.

Once the codes have been set, check operation and reinsert the hatches.

CAUTION: Any changes or modifications in intentional or unintentional radiators which

are not expressly approved by Digi-Code Inc. could void the users authority to operate this

equipment. This applies to intentional and intentional radiators certified per part 15 of the

FCC rules and regulations.

DIGI-CODE, INC.

307 ROBBINS DR. •TROY, MICHIGAN 48083

(248) 589-3645

03/01/00

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digi-Code Garagentoröffner Handbücher

Digi-Code

Digi-Code 5010 Installationshandbuch

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung