DigiDesign VENUE Personal Q Bedienungsanleitung

Digidesign

2001 Junipero Serra Boulevard

Daly City, CA 94014-3886 USA

Technical Support (USA)

Visit the Digidesign Online Support Center at

www.digidesign.com/support

Product Information

For company and product information,

visit us on the web at www.digidesign.com

VENUE Personal Q

Guide

PN 9321-61362-00 REV A 04/09

duplicated in part or in whole without the prior written consent of Avid

Technology, Inc.

Avid, Digidesign, D-Show,Profile and Pro Tools are trademarks or registered

trademarks of Avid Technology, Inc. in the U.S. and/or other countries. All other

trademarks contained herein are the property of their respective owners.

Product features, specifications, system requirements, and availability are

subject to change without notice.

Part Number 9321-61362-00 REV A 04/09

Documentation Feedback

At Digidesign, we are always looking for ways to improve our documentation. If

you have comments, corrections, or suggestions regarding our documentation,

email us at techpubs@digidesign.com.

Communications & Safety Regulation Information

Compliance Statement

The models PQ Rack and PQ Controller comply with the following standards

regulating emissions and immunity:

• FCC Part 15 Class B

• EN55103 – 1, environment E3

• EN55103 – 2, environment E3

• AS/NZS 3548 Class B

• CISPR 22 Class B

• ICES-003 Class B

Radio and Television Interference

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules.

DECLARATION OF CONFORMITY

We, Digidesign,

2001 Junipero Serra Blvd.

Daly City, California 94014-3886, USA

650-731-6100

declare under our sole responsibility that the products

PQ Rack and PQ Controller

complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference

reeived, including interference that may cause undesired operation.

Communications Statement

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user

is encouraged to try and correct the interference by one or more of the following

measures:

• Reorient or locate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any modifications to the unit, unless expressly approved by Digidesign, could

void the user's authority to operate the equipment.

Canadian Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

CE Compliance Statement:

Digidesign is authorized to apply the CE (Conformité Europénne) mark on this

compliant equipment thereby declaring conformity to EMC Directive

89/336/EEC and Low Voltage Directive 73/23/EEC.

Australian Compliance:

Radio and Television Interference

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules.

Safety Statement

This equipment has been tested to comply with USA and Canadian safety

certification in accordance with the specifications of UL Standards: UL60065 7th

/IEC 60065 7th and Canadian CAN/CSA C22.2 60065:03. Digidesign Inc., has

been authorized to apply the appropriate UL & CUL mark on its compliant

equipment.

Warning

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) CAUTION – Refer all servicing to qualified service personnel only. To reduce

the risk of electric shock, do not perform any servicing other than that contained

in the operating instructions unless you are qualified to do so.

13) WARNING – To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

14) To reduce the risk of electric shock, grounding of the center of the plug must

be maintained, if applicable.

15) The AC mains plug or appliance coupler shall be readily available to the

operator as a means of power disconnectioin.

Contents iii

Contents

Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Personal Q System Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Personal Q System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

System Expansion Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operational Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Connection Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PQ Rack Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PQ Controller Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2. Connecting the Personal Q System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connecting Personal Q System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Applying Power to the Personal Q System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Updating PQ System Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting a PQ Controller to a Microphone Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using Two Personal Q Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 3. Using the Personal Q System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Configuring the Personal Q System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting Up PQ Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Configuring Personal Q Mixers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Controlling a Personal Q Mixer from a PQ Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Calling the Console from the PQ Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Locking Out PQ Controllers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

VENUE Personal Q Guideiv

Chapter 1: Introduction 1

Chapter 1: Introduction

The VENUE Personal Q (PQ) system lets performers remotely

control their own monitor mixes on a VENUE system using ei-

ther a VENUE D-Show®Main or VENUE Profile™ console,

paired with a VENUE Stage Rack and a VENUE FOH Rack.

D-Show Main and Profile consoles provide eight built-in, 12 x

2 PQ mixers that can be used to create up to eight indepen-

dent stereo monitor mixes. After a PQ mixer is set up at the

mix position, it can be controlled by the mix engineer from

the Output section of the console, or by an onstage performer

using a PQ Controller.

The PQ system carries control data to and from the console, al-

lowing you to adjust PQ mixer input level, input pan/balance,

and output level. The PQ system does not carry audio signals;

audio signals for monitor mixes are output from any physical

outputs on the Stage Rack or FOH Rack.

Personal Q System Features

The Personal Q system provides remote operation of controls

on the console, and mirrors any changes made to the corre-

sponding controls on the console.

The Personal Q system consists of at least one PQ Rack and

one PQ Controller.

PQ Rack Features

• Provides connections for up to eight PQ Controllers

PQ Controller Features

• Four rotary encoder controls with LED rings for level,

pan/balance, solo, and metering of PQ mixer inputs

(1–8, L, R, and User Inputs)

• Four on/off switches for control of PQ mixer input on/off

status

• Rotary encoder control with LED ring for master volume of

PQ mixer output

• Four 6-character displays for input and control names

• Console call feature allows performer to activate call mes-

sage on console display

• Lockout feature allows performer or console operator to

temporarily lock out PQ Controller from control changes

Personal Q System Components

The following components are included in a Personal Q

system:

PQ Rack

•PQRackunit

•ACpowercord

• PQLinkCable(10ft/3m)

PQ Controller

(Up to 8 PQ Controllers can be connected to each PQ Rack)

• PQ Controller unit

• PQ Controller cable (50 ft/15 m)

System Expansion Options

The Personal Q system allows independent control of up to

eight individual PQ mixes.

PQ Racks In VENUE systems with two Stage Racks, one PQ

Rack can be connected to each Stage Rack, for a total of two

PQ Rack units. When two PQ Racks are used, dual control of

each PQ mix (up to a maximum of 8 available PQ mixers) is

possible. (This is useful when a single performer has two posi-

tions onstage.)

PQ Controllers Each PQ Rack can accommodate 8 PQ Control-

lers, for a maximum of 16 PQ Controllers (2 controllers for

each of the 8 available PQ mixers) on a VENUE system.

For more information on expansion options for VENUE sys-

tems, visit the Digidesign Web site (www.digidesign.com).

VENUE Personal Q Guide2

Operational Requirements

Temperature and Ventilation

VENUE system components should be operated away from

heat sources and with adequate ventilation.

Storage

VENUE system components should be stored and transported

at temperatures not lower than 0 degrees F (–18 degrees C)

and not exceeding 140 degrees F (60 degrees C).

Operation

VENUE system components should be operated at tempera-

tures not lower than 40 degrees F (4 degrees C) and not ex-

ceeding 115 degrees F (46 degrees C).

Water and Moisture

VENUE system components should be operated away from

sources of direct moisture and should be kept clear of liquids

that might spill into the units.

If condensation is present on a VENUE system component,

leave the unit to dry in ambient air for at least one hour before

powering the unit on.

Cleaning and Maintenance

If you need to clean the surface of a VENUE system compo-

nent, use a dry cloth. Do not apply any cleaning solutions,

spray cleaners, or abrasives to the surface.

Connection Requirements

Power Connections

PQ Rack Each PQ Rack requires its own power connection.

Make sure your power source is correctly rated for the number

of units you are connecting. A surge protected power source

(not included) is highly recommended.

PQ Controllers Each PQ Controller is powered by the PQ Rack

through its PQ Controller cable connection.

Chapter 1: Introduction 3

PQ Rack Overview

PQ Rack Front Panel

PQ Controller Ports Each of the 8 PQ Controller Ports accepts a

male 4-pin PQ Controller cable, for connecting a PQ Control-

ler. The PQ Controller port numbers (1–8) correspond directly

to the PQ mixer number (1–8) that is controlled on-screen or

on the console.

PQ Link Connector The PQ Link connector accepts a female

4-pin PQ Link cable, for connecting the PQ Rack to a Stage

Rack. The maximum cable length for this connection is 15 ft

(4.6 m).

PQ Rack Power/Power Fault Indicators These indicators light

to show application of power (green) and any power fault or

interruption (red) for the PQ Rack.

PQ Connection Comm/Fault Indicators These indicators light

to show active communication to a PQ Controller (green) and

any connection fault or interruption (red), for the correspond-

ing PQ Controller port.

PQ Link Comm/Fault Indicators These indicators light to show

active communication between the PQ Rack and a Stage Rack

(green) and any connection fault or interruption (red).

PQ Rack Back Panel

AC Power Connector The AC power connector accepts a stan-

dard modular AC power cord. The PQ Rack power supply is

auto-power selecting (100V to 240V, 50 Hz to 60 Hz) and au-

tomatically works when connected to an AC receptacle in any

country.

Power Switch The Power switch applies power to the PQ Rack

and activates all PQ Controllers connected to the PQ Rack.

Figure 1. PQ Rack Front Panel

PQ Controller ports (1–8) PQ Link connector (to Stage Rack)

PQ Controller Connection Fault/Comm indicators PQ Link Fault/Comm indicatorsPQ Rack Power/Power Fault indicators

Figure 2. PQ Rack Back Panel

Power switch

AC Power connector

VENUE Personal Q Guide4

PQ Controller Overview

PQ Controller Top Panel

Encoder Displays The encoder displays show the name/value

of the PQ mixer input currently controlled by the correspond-

ing rotary encoder.

Rotary Encoders The rotary encoders control the currently dis-

played parameter (level or pan/balance) when turned, or solo

the currently displayed PQ mixer input when pressed. The en-

coder rings display input level or pan settings, or indicate in-

put meter levels, depending on the encoder mode.

On/Off Switches The On/Off switches turn the currently dis-

played PQ mixer input on or off.

Setup Switch The Setup switch puts the PQ Controller in

Setup mode, which displays the port number for the PQ Con-

troller, and lets you adjust display brightness and contrast on

the PQ Controller.

Inputs 1–4 Selector The Inputs 1–4 selector displays PQ mixer

inputs 1–4 on the rotary encoders and displays for adjusting

level and pan/balance.

Inputs 5–8 Selector The Inputs 5–8 selector displays PQ mixer

inputs 5–8 on the rotary encoders and displays for adjusting

level and pan/balance.

L/R/User Inputs Selector The L/R/User Inputs selector dis-

plays the Main Left, Main Right, Center/Mono, and user-as-

signable inputs on the rotary encoders and displays for adjust-

ing level and pan/balance.

Master Volume/Call Control The Master Volume/Call control

changes the PQ mixer output volume when turned, or raises a

call message on the console display when pressed.

Lockout Switch The Lockout switch temporarily locks the lo-

cal controls of the PQ Controller to prevent inadvertent

changes to controller settings. This function does not lock out

control of the PQ mixer from the console. The Lockout switch

lights when lockout is activated from the controller, and

flashes when lockout is activated from the console.

Encoder Mode Switch and Indicators The Encoder Mode

switch and indicators toggle control of input level, input

pan/balance, or input metering on the rotary encoders and

LEDs for the currently displayed input.

Figure 3. PQ Controller Top Panel

Encoder displays

Rotary

Encoders

On/Off switches Inputs 1–4

selector

Inputs 5–8

selector

L/R/User Inputs

selector

Setup switch

Master Volume/Call

control

Lockout switch

Encoder Mode

switch

and

indicators

Chapter 1: Introduction 5

PQ Controller Back Panel

PQ Controller Connector The PQ Controller connector accepts

a female 4-pin PQ Controller cable connector, for connecting

the PQ Controller to a PQ Rack. Power is provided by the PQ

Rack, through the PQ Controller cable. The maximum cable

length for this connection is 100 ft (30.5 m).

Figure 4. PQ Controller Back Panel

PQ Controller connector

VENUE Personal Q Guide6

Inhaltsverzeichnis

Andere DigiDesign Fernbedienung Handbücher

DigiDesign

DigiDesign R1 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung