Digimerge DNS1010 Bedienungsanleitung
Dual-coDec ViDeo SerVer
DNS1010
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
Page 2
www.digimerge.com
DNS1010_Quick Installation Guide_En_R1
IMPORTANT!
This product must be installed in compliance with local laws and regulations.
This installation guide provides instructions for installing the Digimerge
DNS1010 Dual-Codec Video Server on your network. For all other
aspects of using the product, please refer to the user manual avail-
able at www.digimerge.com or on the Installation CD included with this
product.
Package Contents:
• 1 x Dual-Codec Video Server
• 1 x Installation CD with manuals and software
• 1 x Quick Installation Guide
• 1 x Warranty Card
• 1 x Ethernet Cable (1m / 3.3ft)
• 1 x Power Adapter
• 1 x mini-DIN/Terminal Block Conversion Cable (Serial/GPIO)
PACKAGE CONTENTS
Serial / GPIO Port
Ethernet port
Power indicator
DC input
Network indicator
Audio input
BNC video input
BNC video output
DNS1010_Quick Installation Guide_En_R1
www.digimerge.com
Page 3
Mounting Instructions: Run the cables
to the desired location. Securely
mount the device to a wall or other
surface using 4 metal screws (not
provided).
HARDWARE CONNECTIONS
1
Connect the network cable to
the Video Server’s RJ45 network
connector.
A
B
Connect a BNC camera (not included)
to the Video Server’s BNC Input port
(left port). Optionally, an audio input
device (i.e. Microphone) can be con-
nected to the Audio In port. The Video
Out port can be used to connect a
local monitor (no audio).
C
Connect the mini-DIN Terminal Block
cable to the Video Server’s DIN
connector. For more details on the
available Terminal Block connections,
please check the hardware user
manual.
D
Connect the supplied power adapter
to the power connector on the Video
Server.
E
WALL MOUNT TABLE MOUNT
OPTIONAL
Page 4
www.digimerge.com
DNS1010_Quick Installation Guide_En_R1
SOFTWARE INSTALLATION
2
The Digiconsole application loads
from the CD included with your
package, and provides you with the
following:
1. Web links to various resources
and documentation
2. Discovery of all the Digimerge
IP devices on the network
3. Provides Network
configuration of IP Devices
4. Installs DigiConsole and
Surveillance application on your
local PC
5. Warranty information and DDNS
registration
A
Digiconsole Utility screen consists of
the following menus:
1. Home
2. Find Devices
3. Register
4. Install
B
DNS1010_Quick Installation Guide_En_R1
www.digimerge.com
Page 5
Home:
Provides basic Digiconsole operating
instructions, links to product informa-
tion/documentation as well as 3rd party
software support links.
SOFTWARE SET-UP
A
Find Devices:
Locates all available Digimerge IP
devices on your network and displays
a snapshot of the results. Click on any
available device to display image on
the right side screen display.
NOTE: You may need to press the Find
Devices button several times as some
devices may not respond immediately.
If you do not see a camera image,
please check that all cables running
from the Video Server to the Camera
are connected properly. A camera
must be connected and networked to
view live images.
B
C
Menu:
The Menu Button or right clicking on
a device icon provides access to
device specific settings:
• Edit Network Parameters
• View Live Image
• Open Device in Browser
• Update Firmware in Video Device
• Refresh the device list - in order to
remove inactive and disconnected
devices
NOTE: It is recommended that you
record the device specific MAC and
IP address for DDNS registration
purposes. If you have multiple
cameras on a local network, only
one camera needs to be configured
for DDNS.
3
MAC:
IP:
Page 6
www.digimerge.com
DNS1010_Quick Installation Guide_En_R1
SOFTWARE SET-UP
Edit Network Parameters:
The Network Parameters are
automatically assigned to the
Device by the network router (by
using DHCP). These settings can
be manually changed if desired.
1. Select the IP device you would
like to edit by clicking on its icon.
2. Click on the MENU button or
right click the icon for the device
to access the menu. Select
“Edit Network Parameters” from
the menu.
3. Make the necessary changes
and click OK to save changes or
click CANCEL to close the
window without saving any of the
changes made.
NOTE: If a user name and password
were set-up on the IP Device previ-
ously, you will be required to enter
this authentication information when
attempting to access the device.
C1
Continued
View Live Image:
View live video from the IP Device
using the Apple Quicktime program.
If this application is not installed on
your system, please download it (no
charge) at
http://www.apple.com/quicktime
C2
3
OPTIONAL
If by clicking VIEWING LIVE IMAGE
the image is not automatically shown
in Quicktime, follow these steps in
Quicktime:
1. Go to FILE
2. Choose OPEN URL
3. Enter the following: rtsp://<device
IP address> (i.e. rtsp://192.168.2.102)
A device IP address can be obtained
from the Digiconsole device list.
NOTE: Minimum Quicktime version installed
should be 7.1.6. If you cannot install Quick-
time, use Microsoft Internet Explorer to view
the device. See step C3 for details.
DNS1010_Quick Installation Guide_En_R1
www.digimerge.com
Page 7
SOFTWARE SET-UP
Continued
Open Device in Browser:
Opens up the DigiViewer Video Browser
using your default web browser (e.g.
Internet Explorer).
The DigiViewer browser allows the user
to view streaming video from the device
as well as change certain settings on the
device depending on the level of access
set by the administrator.
C3
3
Once user names and passwords are set
up by the administrator, the users (except
for a VIEWER level user) are required to
enter this information every time they ac-
cess the DigiViewer.
Click (during streaming mode)
to mute the audio.
Click to capture a snapshot image
in a new browser window.
By default, the image refresh rate
is set to OFF. Move slider to the
right to set image refresh rate.
Click to bring up image brightness and contrast controls
Click to capture a video clip and send it to a FTP site. FTP
must be configured in the SETTINGS screen
Click here to start streaming video
Page 8
www.digimerge.com
DNS1010_Quick Installation Guide_En_R1
SOFTWARE SET-UP
3 Levels of User Access:
• Administrator (current user)
• Operator (general user)
Default User Name: guest
Password:<leave blank>
• Viewer (anonymous guest)
Creating Current User Account:
1. Click SETTINGS
2. Select ACCOUNTS
3. Fill in a user name and
password in the assigned fields
4. Reconfirm password
5. Click UPDATE ACCOUNTS
1. Administrator: Administrator has
unrestricted access to all the
settings of the device. The
interface will only permit creation
of ONE administrator account.
2. Operator: Operator has restricted
access to the settings of the
server. The interface will only
permit creation of FIVE operator
accounts.
Note: Restrictions - View images.
Requires username and password.
3. Viewer: The interface will permit
the creation of ONE viewer
account (i.e. Anonymous Guest).
This account does not require a
password.
Note: Viewer Restrictions - View im-
ages if permission is granted by ad-
ministrator. Note that the permission
in this case refers to providing the
IP address to someone. Whomever
receives the IP address can view the
camera remotely as a anonymous
guest. No password is required.
Multiple users can access the de-
vice at the same time, however this
will limit the quality and speed of the
video as the feed is shared between
all connected users.
Continued
3
DNS1010_Quick Installation Guide_En_R1
www.digimerge.com
Page 9
This page is intentionally left blank.
Page 10
www.digimerge.com
DNS1010_Quick Installation Guide_En_R1
REGISTRATION & SOFTWARE INSTALLATION
Register:
Provides you with information on the
device warranty and/or free DDNS
service.
D
Install:
Click the Install button to install the
Digiconsole application software
on your computer. Click NEXT and
follow the instructions to complete the
installation. Once the installation is
complete you can access the software
by clicking
START--->PROGRAMS--->
DIGIMERGE TECHNOLOGIES--->
DIGICONSOLE
NOTE: When you install Digiconsole
on a PC, it will also install Surveillance
Software (see section F for further
details).
For detailed set-up information, please
refer to the user manuals available on
the Digimerge website or on the
Installation CD included with the
device.
NOTE: Installation is not required,
however installing the software on your
local computer allows you to use the
utility to locate and update cameras on
the network from your PC.
E
Update Firmware in Video Device:
Opens up a window to search your
computer for downloaded firmware
(with .bin extension).
NOTE: This product will not auto-
matically check for firmware updates.
Please visit the Digimerge website to
download the most current firmware
for your product.
C4
4
OPTIONAL
OPTIONAL
Inhaltsverzeichnis
Andere Digimerge Server Handbücher
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung