Digital Equipment MM-10 Series Bedienungsanleitung

EK-DLXFI-IM. A01

Installing and Cabling the 10BaseFL MM-10 (DLXFI)

Introduction

The 10BaseFL MM-10 is part ofthe MM-10 product family(which also includes the 10BaseT, 10Base2, AUI, and

Reverse AUI). It provides connectivity between a host module such as the DIGITAL MultiSwitch Hub 624T and

network devices using 10BaseFL. The MM-10has jumpers that controlthe MM-10 configuration, suchas enabling

SQE test or monitoring transmit or receive data.

Configuring Jumpers on the 10BaseFL MM-10 Option Card

The MM-10 jumpers are set to the most commonly-used configurations. For special applications or

troubleshooting, you may wish to reconfigure the jumper settings. Refer to the following figure and table.

10BaseFL MM-10 Jumper Locations

Item Jumper Description Default

1ACT —> Sets Activity LED to blink on for:

• RX = receive packets only

• TX = transmit packets only

• BOTH = all packets

BOTH

NPB-0811-97F

DLXFI-MA

NPB-0801-97F

Installation Procedure

The 10BaseFL MM-10 installs into one of the Carrier Card slots and is hot-swappable. To install the 10BaseFL

MM-10, complete the following steps. A Phillips-head screwdriver is required.

Note: Installing MM-10s into the DIGITAL MultiSwitch Hub 624T requires prior installation of the DIGITAL

MultiSwitch Hub 624T Carrier Card, part number DLXMC-MA, which is not hot-swappable.

1Hold the 10BaseFL MM-10 by its bezel and align its edges (1) with the card guides (2) in the Carrier Card.

Push the 10BaseFL MM-10 into the slot until it is firmly seated inside the module.

2Align and securely fasten the two screws.

3Ensure that the key is correctly positioned while aligning the transmit cable connector (1) with the transmit

port (2) and the receivecable connectorwith the receiveport.Turntheconnectorscounterclockwisetolock

into position. Connect the other end of the cable to your network end device.

For further configuration and LED state information, see the DIGITAL MultiSwitch Hub 624T Installation and

Configuration manual.

DIGITAL and the DIGITAL logo are trademarks of Digital Equipment Corporation.

2SQE Test Enables SQE test

0 = Disable; 1 = Enable Disable

3FDX Full Duplex operation

0 = Half Duplex, 1= Full Duplex Half Duplex

Item Jumper Description Default

NPB-0597-96F

12V

NPB-0650-96F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digital Equipment Steuereinheit Handbücher

Digital Equipment

Digital Equipment VNswitch 900FF Bedienungs- und Wartungsanleitung

Digital Equipment

Digital Equipment DECrepeater 900GM Bedienungs- und Wartungsanleitung

Digital Equipment

Digital Equipment MM-10 Series Bedienungsanleitung

Digital Equipment

Digital Equipment AUI MM-10 Bedienungsanleitung

Digital Equipment

Digital Equipment DECrepeater 900TM Bedienungs- und Wartungsanleitung

Digital Equipment

Digital Equipment Mod-MAC Series Bedienungsanleitung

Digital Equipment

Digital Equipment DECrepeater 90FS Bedienungs- und Wartungsanleitung

Digital Equipment

Digital Equipment VAX 6000 XMI-1 Bedienungsanleitung

Digital Equipment

Digital Equipment ML200-AA Bedienungsanleitung

Digital Equipment

Digital Equipment PDP-8 Bedienungsanleitung

Digital Equipment

Digital Equipment Pro-face GP-377R Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung