Digital Equipment HD4000 Bedienungsanleitung
HD4000
1
Safety Instructions
•Always read the safety instructions carefully
•Keep this User's Manual for future reference
•Keep this equipment away from humidity
•Place this equipment on a reliable flat surface before setting it up.
•Do not stand it on soft furnishings.
•If any of the following situation arises, get the equipment checked by a service
technician:
- The equipment has been exposed to moisture.
- The equipment has been dropped and damaged.
- The equipment has obvious sign of breakage.
- The equipment has not been working well or you cannot get it work according
to User's
Manual.
Warning
•To prevent the risk of electric shock, do not open the cover or the back of the
receiver.
•Do not block the ventilation holes of the device. Leave appropriate gap above
and around it to allow for adequate ventilation.
•Do not place the device in an unventilated cabinet or on top of a unit which emits
heat.
Copyright Statement
No part of this publication may be reproduced in any form by any means without
the prior written permission. Other trademarks or brand names mentioned herein
are trademarks or registered trademarks of their respective companies.
Disclaimer
Information in this document is subject to change without notice. The manufacturer
does not make any representations or warranties (implied or otherwise) regarding
the accuracy and completeness of this document and shall in no event be liable for
any loss of profit or any commercial damage, including but not limited to special,
incidental, consequential, or other damage.
This symbol indicates that this product incorporates double insulation
between hazardous mains voltage and user accessible parts. When
servicing use only identical replacement parts.
WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or colds.
2
Table Of Contents
Introduction............................................................................................3
Front panel and rear panel illustration.................................................4
Front Panel...........................................................................................4
Rear Panel............................................................................................4
Remote control.......................................................................................5
Installing the batteries...........................................................................5
Installation & Connections....................................................................7
First time installation...........................................................................10
Basic operations..................................................................................11
Main menu ............................................................................................14
Menu Tree ..........................................................................................15
Installation............................................................................................16
Auto Scan...........................................................................................16
Manual Scan.......................................................................................16
Program edit.........................................................................................17
System setup........................................................................................19
A/V Output Settings............................................................................19
Local Time Setting..............................................................................19
System Information.............................................................................19
Factory Default...................................................................................19
User preferences..................................................................................20
OSD Language...................................................................................20
OSD Transparency.............................................................................20
CH Info Bar Time Out.........................................................................20
Volume Bar Time Out .........................................................................20
Parental Control..................................................................................21
Trouble shooting..................................................................................22
Technical specifications......................................................................23
WARRANTY INFORMATION
WARRANTY CONDITIONS
3
Introduction
This DVB-T TV Receiver is a Free-To-Air digital terrestrial receiver, allowing you to
access free-to-air digital terrestrial TV channels and radio broadcasts on your TV
set. Its digital reception covers VHF & UHF band. Compared with the analog TV
programs, digital TV programs eliminate the noise and interference but offer high
quality video and audio. An on-screen initial installation guide is provided so that
you can easily start to enjoy watching the programs. In addition, a fully featured
remote control is included that offers you access to every feature with a simple
press of a button.
Main Features
- Full comply with Australian DVB-T standards
- Full MPEG2 ISO/IEC 13818 transport stream compliant audio/video decoding
- Bandwidth of 7MHz supported
- COFDM demodulator
- Automatic/manual channel search
- Channel edit, moving and deletion
- Parental lock control
- EPG (Electronic Program Guide) and teletext function (where available)
- RS-232 serial port for software upgrade
- Tuner RF in/loop through
- Dolby R Digital 5.1 Channel Surround Sound
- Component/S-Video/Digital Audio via coaxial & optical output
- HDMI output
- Full function remote control
Package Contents
Before installation, please check the items of the package. The package should
contain the following items:
1.DVB-TTVreceiver x1
2.Remotecontrol x1
3. AAA size battery for the remote control x 2
4.Instructionmanual x1
5.YPbPrcable x1
6. CVBS cable x 1
4
Front panel and rear panel illustration
Front Panel
①
①Green Light To indicate the Stand-by mode ON/OFF (this mode is controlled
by remote control only).
Rear Panel
①ANT IN connect the antenna here.
②LOOP OUT To connect a RF signal from the STB to either the RF Input jack
(antenna) on your VCR or to the antenna input of your TV.
③HDMI video output used to connect to your HDMI device.
④PDIF/COAXIAL Digital audio output.
⑤S-VIDEO Y/C output for a S-VHS or Hi-Fi Video Recorder.
⑥AUDIOL/R Audio output to connect to your TV.
⑦YPbPr High definition video output to connect to your TV.
⑧VIDEO CVBS output to connect to your TV.
⑨VGA Video output to connect a VGA display monitor.
⑩RS-232 Serial port for software upgrade.
⑪POWER Switch ON/OFF.
5
Remote control
Remote key functions:
1. POWER To turn the Stand-by mode
ON/OFF.
2. INFO To display the current program
information.
3. Numeric buttons (0-9) To control the
numerical operation and especially to change
program directly.
4. SUBT To switch the close caption
ON/OFF.
5. AUDIO To display the Audio info of the
selected program.
6. MENU To enter into the main menu, Press
again to exit to previous menu.
7. VOL - / + To control the level of the
volume.
8. PAGE - / +To Page Down (5-)/Page Up
(5+).
9. OUTPUT To switch the output mode of HD
between YPbPr and VGA.
10. EDIT To edit the properties of the current
program.
11. RECALL To return to view the previous
program.
12. MUTE To mute or recover the sound of the receiver.
13. TTX To switch the teletext service ON/OFF.
14. TV/RADIO To switch the program between TV and Radio.
15. EXIT To cancel operation or exit the menu directly.
16. ▲▼To change the program upward / downward.
17. OK To confirm the selected menu item / to open the program list.
18. FAV To cancel operation or exit the menu directly (Not supported now)
19. EPG To introduce some program info to the user.
20. 4 COLOR KEY To assist the operation of the box.
21. FORMAT To switch the different resolution (1080i, 720P, 576P , 576i
supported).
22. ASPECT To toggle among 16:9 full screen, 16:9 letter box, 4:3 full screen, 4:3
letter box, 4:3 panscan.
23. PAUSE To Pause the current program when pressed and go on playing the
current when pressed again.
24. SIGNAL To show the quality / level of signal.
6
Installing the batteries
Remove the battery cover from the remote control and put two AAA size batteries
inside the compartment.
The diagram inside the battery compartment shows the correct way to install the
batteries.
Caution:
1. Keep batteries out of children’s reach.
2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the batteries
into the fire.
3. Always replace both batteries at the same time. Never mix new and old batteries
or batteries of a different type.
4. If you don’t intend to use the remote controller for an extended period, remove
the batteries to prevent possible leakage and corrosion.
5. Do not drop, apply shock or step on the remote control.
6. Do not spill water on the remote control.
Notes: If the receiver does not operate when operating the remote control from a close
range, you need to replace the batteries.
Using the Remote Control
1. To use the remote control, point it towards the front of the digital set top box.
2. The remote control has a range of up to 7 metres from the set top box at an
angle of up to 60 degrees.
3. The remote control will not operate if its path is blocked.
Note: Sunlight or very bright light will decrease the sensitivity of the remote control.
7
Installation and Connections
How to get good reception
• In general you are not required to change the existing antenna. However if your
antenna is not in good condition you should consider replacing them to ensure
uninterrupted digital television viewing.
•Viewers in areas of poor analog reception may need specialists’ advice about
antenna requirements for digital reception in their area.
•It’s recommended that viewers use quad shielded cable from the antenna to the
television.
Connections to a TV
There are several ways of connecting your STB receiver to the TV and Hi-Fi
System. For high definition viewing your TV must support either 576p, 720p, 1080i
resolution. Also the connection between the STB receiver and TV must be YPbPr
component, VGA, or HDMI. Other connection will provide standard definition
viewing.
Connect the STB receiver via Video/S-Video and Audio
(for standard definition viewing)
8
Installation and Connections
Connect the STB receiver via YPbPr output and Audio output
(for high definition viewing)
Connect the STB receiver via VGA output and Audio output
(for high definition viewing)
Inhaltsverzeichnis
