Technical Support
Phone: (248) 236-0061, Mon.-Fri., 9:30am-5:30pm
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. owever, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: a) Reorient or relocate the receiving antenna
b) Increase the separation between the equipment and receiver c) Connect the equipment into an outlet on
a circuit different from that to which the receiver is connected d) Consult the dealer or an experienced
radio/TV technician for help.
Note 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
BEFORE FIRST USE
Your owerNow! 6600 comes from the factory with a charge and can be used
right out of the box. owever, it is best to make sure that the unit is fully charged
before first use. Press the ower Button to see how much charge is in the unit.
The Battery Status LEDs light up from left to right to show the charge level. The
Battery Status LEDs will turn off after a few seconds.
• One LED Lit: 25% Charged • Two LEDs Lit: 50% Charged
• Three LEDs Lit: 75% Charged • Four LEDs Lit: 100% Charged
Charging the owerNow! 6600™
To charge the owerNow! 6600, insert the Micro USB end of the included USB
to Micro USB Charging Cable into the power bank’s Micro USB ower Input
ort and the other end into a USB ort on your computer or the included USB
wall adapter. The Battery Status LEDs light up to indicate the current power
level. All four lights glow steadily when the unit is fully charged.
Charging a Smartphone, Camera, or Other Device
To charge a smartphone or similar device with the owerNow! 6600, plug the
device into either of the USB ower Output orts and press the On/Off
Button. The Battery Status LEDs light up, showing the percent of power
remaining in the owerNow! 6600. When the device is fully charged, the
Battery Status LEDs turn off. You may charge two smartphones (or similar
devices) at one time by plugging one into each USB ower Output ort.
25%
Charged
50%
Charged
75%
Charged
100%
Charged 2.1 Amp USB
ower Output ort
On/Off
Button
1.0 Amp USB
ower Output ort
Charging a Tablet
To charge a tablet with the owerNow! 6600, plug the device into the
2.1 Amp USB ower Output ort and press the On/Off Button. The Battery
Status LEDs light up, showing the percent of power remaining in the owerNow!
6600. When the device is fully charged, the Battery Status LEDs turn off.
IMPORTANT:
If you plug the tablet into the 1.0 Amp USB ower Output
ort, it MAY NOT CHARGE. The 1.0 Amp USB ower Output ort does not
provide strong enough power output to charge most tablets.
Using the LED Flashlight
To activate the LED Flashlight, press the On/Off Button two times. Press the
On/Off Button two more times to turn the LED Flashlight off.
Troubleshooting
The owerNow! 6600 Will Not Charge - Check to make sure that the USB to
Micro USB Charging Cable is properly connected to the Micro USB ower In
ort. If the unit still will not charge, your power cable may be damaged. Connect
the unit using a different power cable.
A Smartphone Will Not Charge - Check to make sure that the smartphone
is securely connected and the owerNow! 6600 is charged. Recharge the
owerNow! 6600 if necessary. If the smartphone still will not charge, your power
cable may be damaged. Connect the smartphone using a different power cable.
A Tablet Will Not Charge - Check to make sure that the tablet is securely
connected to the 2.1 Amp USB ower Output ort. The 1.0 Amp USB ower
Output ort does not have a strong enough power output to charge a tablet.
Make sure that the owerNow! 6600 is charged. Recharge the owerNow! 6600
if necessary. If the tablet still will not charge, your power cable may be damaged.
Connect the tablet using a different power cable.
CAUTION:
Store the owerNow! 6600 in a cool, dry place. Avoid water and corrosive
chemicals. Do not violently shake or strike. Device contains no user-serviceable
parts. Do not disassemble. If the device is overheating or smoking or if the case
is damaged, deformed, or discolored, immediately discontinue use and contact
the manufacturer.
How to roperly Dispose of Batteries
This product contains lithium-ion batteries. To properly dispose of expired
batteries, view your city’s website or newsletter to find what guidelines, if any,
should be followed and to make note of their hazardous waste collection days.
