DigitaLinx DL-HD2100 Bedienungsanleitung
DL-HD2100 Quick Install Guide
This guide is for quick installa on only.
For complete owners manual go to www.libav.com or use a QR reader to access the
manual via QR code below.
Scan QR Code with your Smart-phone or Tablet
11675 Ridgeline Drive
Colorado Springs, CO
80921
Rev 181211 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
The DigitaLinx DL-HD2100 HDBaseT extender set extends HDMI audio, video as well as control
up to 100m / 330’ using a single Category 6 cable. Supports HDMI 2.0a, HDR10 and HDCP 2.2
as well as Dolby Atmos and DTS:X audio formats. Control extension supports bidireconal IR,
Ethernet, ARC and RS232. Built in re-clocking circuitry ensures that extender set is backwards
compable with older HDMI version chip sets.
The DigitaLinx DL-HD2100 can transport HDMI data rates up to 18Gbps up to 100 meters.
The system enables high data rates by ulizing visual lossless compression at a 2:1 data
compression rate when the signal surpasses 10Gbps, anything under 10Gbps will never be
compressed. Supports stac HDR (HDR10) only when data rate exceeds 18Gbps, supports
dynamic HDR (HDR10+ / Dolby Vision) when data rate is 10Gbps or less.
Built-in surge protecon and diagnosc LEDs ensure hassle-free and robust installaons.
Flexible power design allows the units to be powered at either the TX or RX end, and only one
power supply is required to power the set. The 12 volt power supply is secured with a screw-
on connector to prevent the power from being accidentally disconnected.
The DL-HD2100 is sold only as a set. The individual transmier and receiver are not compable
with other HDBaseT devices due to proprietary PoE circuitry.
Product Overview
Package Contents
• (1) DL-HD2100 Transmier and Receiver Set
• (2) IR Receivers (Eye)
• (2) IR Transmiers (Emier)
• (1) IR-AC IR Coupler Cable
• (3) 3 pole Terminal Block (aached to extenders)
• (1) DC12v US Power Supply with US, UK, EU and AU adapters
• (4) Mounng Brackets with screws
Transmi er
1. FRONT PANEL DIAGNOSTIC LEDs;
• POWER -Solid, the DL-HD2100 extender is receiving power from the power supply or from the remote extender
via Category 6 cabling.
• STATUS - Flashes once per second, the HDBaseT processor is running.
• HDCP - Solid, HDCP signal is present in the HDMI stream. Flashes quickly, non-encrypted HDCP signal is present
in the HDMI stream.
• LINK - Solid, the two DL-HD2100 components are communica ng via Category cabling.
2. DC 12V
• Locking power port, connect DC12V power adapter to transmi er (either power port on transmi er and
receiver can power en re set)
3. HDBT OUT
• RJ45 HDBaseT connec on. Connect Cat6 cable to receiver
4. IR In / IR OUT
• 3.5mm IR input port for connec on to IR receiver or IR system
• 3.5mm IR output port for connec on to IR emi er
5. AUDIO OUT
• Analog audio de-embedding port for rou ng stereo audio to audio ampli er / mixer
6. RS232
• 3 pin Phoenix connector port for connec ng / passing RS232 control to receiver / display loca on
7. HDMI In
• HDMI input port for connec ons to video sources
8. Ethernet
• RJ45 port for passing Ethernet to receiver / display loca on
9. TOSLINK OUT
• Digital audio return channel output port for rou ng mul -channel from DL-HD2100 receiver to audio ampli er
or mixer
1 2 3 4 5 67 8 9
Receiver
1. FRONT PANEL DIAGNOSTIC LEDs;
• POWER -Solid, the DL-HD2100 extender is receiving power from the power supply or from the remote extender
via Category 6 cabling.
• STATUS - Flashes once per second, the HDBaseT processor is running.
• HDCP - Solid, HDCP signal is present in the HDMI stream. Flashes quickly, non-encrypted HDCP signal is present
in the HDMI stream.
• LINK - Solid, the two DL-HD2100 components are communica ng via Category cabling.
2. DC 12V
• Locking power port, connect DC12V power adapter to receiver (either power port on transmi er and receiver
can power en re set)
3. HDBT IN
• RJ45 HDBaseT connec on. Connect Cat6 cable to transmi er
4. IR In / IR OUT
• 3.5mm IR input port for connec on to IR receiver or IR system
• 3.5mm IR output port for connec on to IR emi er
5. AUDIO CONTROL
• ARC - When ARC mode is selected, an HDMI cable from the HDMI OUT should connect to an ARC compa ble
input on a display, digital audio will then de-embed from the TOSLINK OUT on the DL-HD2100 transmi er
• TOSLINK - When TOSLINK mode is selected, a Toslink cable should be connected from the displays digital audio
output to the TOSLINK IN on the DL-HD2100 receiver, digital audio will then de-embed from the TOSLINK OUT
port of the DL-HD2100 transmi er
6. RS232
• 3 pin Phoenix connector port for connec ng / passing RS232 control from transmi er loca on
7. HDMI In
• HDMI input port for connec ons to video sources
8. Ethernet
• RJ45 port for passing Ethernet from transmi er
9. TOSLINK IN
• Digital audio return channel input port for injec ng digital audio signal from display (only in TOSLINK mode)
1 2 3 4 5 67 8 9
Connec vity Instruc ons
1. Verify all components included with the extender set are present before
installa on.
2. If the extenders are going to be permanently mounted to a surface, a ach the
included moun ng brackets with the supplied screws.
3. Turn off power and disconnect the audio/video equipment by following the
manufacturer’s instruc ons.
4. Connect Category 6 or greater twisted pair cable with RJ45 connectors between
the transmi er and the receiver. TIA/EIA-568B straight-through wiring connec ons
must be used with all HDBaseT extenders.
5. Connect an HDMI cable and any desired control accessories between the
display and the receiver.
6. Connect an HDMI cable and any desired control accessories between the source
and the transmi er.
7. Connect the included power supply to the transmi er or receiver and lock the
power supply to the power connector by twis ng the locking collar clockwise.
8. Power on a ached audio/video devices.
Passing IR Signals:
The DL-HD2100 is capable of passing IR signals between 33 and 55 KHz. To
prevent damage to any of the electronics, the extenders should be powered off
while inser ng or removing any IR components. Inser ng an IR transmi er into
the IR IN port may damage the IR circuit for that extender.
IR OUT: The IR transmi er (IR emi er) must be plugged into the IR OUT port.
IR IN: The IR receiver (IR eye) must be plugged into the IR IN port.
To connect to a 3rd party IR system such as a control system, connect the TS
connector of the IR-AC coupling cable to the IR output port of the control
system and connect the TRS connector of the IR-AC cable to the IR IN to either
transmi er or receiver of the DL-HD2100.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connec on between send and receive
units.
Cabling Requirements
RS232 Wiring
Connect the controller or device RXD signal
to Tx on the DL-HD2100 extender. Connect
the controller or device TXD signal to Rx on
the DL-HD2100 extender.
To ensure proper performance of the DL-HD2100, it is recommended that you use solid core
Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform well but may not
support power over HDBaseT reliably.
For op mized performance use the following Liberty Wire and Cable branded cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6A NON -plenum; 24-4P-L6ASH
When using shielded category cabling ALWAYS...
....use shielded connectors
....properly ground the category cable
Tx RXD
GND
Rx TXD
DL-HD2100
(TX/RX)
Controller or
Device
rev 181010
Liberty AV Soluons
11675 Ridgeline Drive
Colorado Springs, CO 80921
800-530-8998
supportlibav@libav.com
Technical Specicaons
Supported Audio and Video
Video Compliance HDMI 2.0+, HDCP 2.2, ARC (Audio Return Channel) and CEC (Consumer Electronics Control)
Input / Output Resoluon Support SMPTE: Up to 4096x2160@60Hz (4:4:4 chroma sub-sampling / 8 bit deep color)
VESA: Up to 1920x1200
Maximum Pixel Clock 594MHz
Embedded Audio Up to PCM 8 channel, Dolby Atmos, DTS: X, Dolby TrueHD, DTS-HD Master Audio, Dolby Digital
and DTS
IR Carrier Frequency Range 33-55kHz at 5 volts
RS232 Baud Rate Up to 115200 baud
HDBaseT Signal Characteriscs
Maximum Distance 1080p: 100 meters / 328 feet
4K@60Hz 4:4:4: 70 meters / 229 feet
Cable Requirements Solid core F/UTP Category 6 cable or greater with TIA/EIA-568B crimp paern
Bandwidth 18 Gbps (compressed) / 10.2 Gbps (uncompressed)
Chassis and Environmental
Dimensions TX- 195mm x 94.8mm x 21mm (7.7 in. x 3.7 in. x 0.8 in.)
RX- 195mm x 94.8mm x 21mm (7.7 in. x 3.7 in. x 0.8 in.)
Operang Temperature (Environment) TX/RX - 0° to +45° C (+32° to +113° F)
Operang Temperature (Chassis) 31° C (88° F) (TX); 38° C (100° F) (RX)
Operang Humidity (Environment) 10% to 90%, Non-condensing
Product Weight 0.4kg / 2.2 lbs
Power
Maximum Power Consumpon 27 was (TX)- when receiver is powered by transmier
27 was (RX) - when transmier is powered by receiver
Power Supply Input Voltage 100-240V AC at 50-60 Hz
Power Supply Output Voltage DC 12V 3A
ESD Protecon ±8kV(Air-gap discharge)/
±4kV(Contact discharge)
Surge Protecon Voltage: ±1 kV
Regulatory CE, FCC
Other
Standard Warranty 5 Years
Included Items (1) Transmier, (1) Receiver, (1) Quick Install Guide, DC 12V Power Supply with US, UK, EU
and AU adapters, (2) IR Transmiers, (2) IR Receivers, (1) IR-AC IR coupler cable, (4) Mounng
Brackets, Mounng Screws
Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8998 or email us at supportlibav@libav.com
www.libav.com
Digitalinx is a brand of:
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: 719-260-0061
Fax: 719-260-0075
Toll-Free: 800-530-8998
Andere Handbücher für DL-HD2100
2
Inhaltsverzeichnis
Andere DigitaLinx Extender Handbücher
DigitaLinx
DigitaLinx DL-HD70LS-H2 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD70 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-UHDRC70 Bedienungsanleitung
DigitaLinx
DigitaLinx IPEX2001 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-RMKTC2H-2 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDE100 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD2100 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD70 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-UHDRC70 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD70LS Bedienungsanleitung
DigitaLinx
DigitaLinx DL-UHDRC70 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-UHDRC70 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDFO Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD2100 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDE100 Bedienungsanleitung
DigitaLinx
DigitaLinx DL-DVI-S Betriebsanleitung
DigitaLinx
DigitaLinx DL-HD70LSIR Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD50C Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HD70LS-TX Bedienungsanleitung
DigitaLinx
DigitaLinx DL-1H1A1U-WPKT-W Bedienungsanleitung
