DIGITIZE DET-6C Bedienungsanleitung

DET-6C/12C

INSTALLATION

AND

OPERATION MANUAL

Digitize, Inc.

158 Edison Road

Lake Hopatcong, NJ 07849

el: (973) 663-1011 Part Number 700174-0000

Fax: (973) 663-4333 Issue Revision: D

E-mail: <info>@digitize-inc.com Issue Date: 02/16

Website: http://www.digitize-inc.com

he DIGI IZE logo is registered trademark of Digitize, Inc.

PROPRIETARY NOTICE

AND DISCLAIMER

DIGITIZE, INC.

158 EDISON ROAD

LAKE HOPATCONG, NJ 0 849-221

PH: (9 3) 663-1011

FAX: (9 3) 663-4333

E-Mail: info@digitize-inc.com

Website: http://www.digitize-inc.com

This manual has been prepared by DIGITIZE, INC. for use by its licensees, distributors

and customers. The information contained herein is the property of DIGITIZE, INC. and

may not be copied, disclosed or reproduced, in whole or in part, without the prior written

approval of DIGITIZE, INC. ny unauthorized disclosure to, or use of the enclosed

information by, unauthorized third persons shall void any and all representations,

warranties and obligations on the part of DIGITIZE, INC.

DIGITIZE, INC. reserves the right to make changes to the specifications and material

contained herein without prior notice. The information and/or examples (including, but

not limited to circuitry, wiring diagrams, programming, the operation or use shown)

described in this manual are intended solely to illustrate the operating principles of the

particular product. They are not a warranty, representation or guarantee that a particular

example or use shown will perform in a particular situation. They are given for illustration

purposes only. DIGITIZE, INC. shall not be responsible, nor does it represent, that any

example of illustration will perform in a particular environment or practice unless it

specifically makes a representation to that effect.

The material set forth herein is for informational purposes only, and DIGITIZE, INC.

assumes no patent liability with respect to any information or illustrations contained

herein.

TABLE OF CONTENTS

SECTION 1 GENERAL INFORMATION 1-1

1.1 SYS EM DESCRIP ION 1-1

1.2 DESCRIP ION 1-1

1.3 AC IVA ION OF INPU S 1-2

1.4 REPOR ING OF INPU S 1-2

1.5 NUMBER OF ROUNDS 1-3

1.6 RANSMISSION SPEED 1-3

1.7 EPROM 27C512 1-3

1.8 INDICA ORS LEDS 1-3

1.9 SPECIFICA IONS 1-3

1.9.1 CURREN CONSUMP ION 1-3

1.9.2 DEMENSIONS 1-3

1.10 APPLICABLE PUBLICA IONS 1-4

SECTION 2 PROGRAMMING THE DET-6C/12C EPROM 2-1

2.1 DIGI IZE, INC. DE -6C/12C PROGRAM DA A LOCA IONS 2-1

2.2 PROCEDURE FOR USING HE DE -PROG PROGRAMMER 2-5

2.2.1 IMING AND OP IONS 2-7

2.2.2 SE ELEGRAPH CODES 2-9

SECTION 3 INSTALLATION 3-1

3.1 HANDLING 3-1

3.2 SI E LOCA ION 3-1

3.3 INS ALL ION DE AILS 3-1

SECTION 4 THEORY OF OPERATION 4-1

4.1 GENERAL 4-1

4.2 WA CH DOG IMER 4-1

SECTION 5 MAINTENANCE 5-1

5.1 PRECAU IONS 5-1

5.2 ROUBLESHOO ING 5-1

5.3 BA ERY MAIN ENCE 5-2

DE -6C/12C INS ALLA ION AND OPERA ION MANUAL

DIGI IZE, INC. 700174-0000 REV.D 02/16 1-1

SECTION 1

GENERAL INFORMATION

1.1 SYSTEM OVERVIEW

he DIGI IZE Electronic ransmitter, Six Zone (DE -6C) is a solid-state

microprocessor coder for use over telegraph hard wire. he DE -6C is designed to

operate with a loop current from 50 mA to 750 mA. A dual 6-zone version (DE -12C) is

available.

1.2 DESCRIPTION

he DIGI IZE DE -6C is a elegraph ransmitter for Fire and Security Alarms. he

unit has six End of Line (EOL) resistor zones and includes a CAM lock, AC transformer,

standby battery and built-in charger. he unit is housed in a cast aluminum cottage shell

and is suitable for mounting on any wall. he DE -6C can be used on the same loop

with mechanical Fire Alarm Boxes. he DE -12C has twelve EOL resistors and a pull

handle for zone 1. An optional push button version uses zone 2 for POLICE, zone 3 for

AMBULANCE, and zone 4 for ROAD SERVICE.

elegraph codes unique to each of the six zones for rouble, Alarm and Secure as well as

Low Battery are transmitted over a 100-mill ampere circuit using PNIS (Positive Non-

Interfering Successive). he DE -6C has line current detection to avoid clashes between

more than one transmitting device. Automatic ground return, a Watch Dog imer, and a

jumper selected internal trouble buzzer assure continued main system operation and

operator notification in the event of a box failure. A built-in trouble relay output (Form

C) and the ground and code relay (grounding, opening, or no effect on the 100 mA line)

are activated by the Watch Dog imer ensuring reliable failure detection.

ransmission speed is adjustable to match existing decoding units, as are the number of

digits for the box number and the last digit for alarm, trouble, and restore. Number of

rounds for each condition is also programmable.

Automatic switchover to battery power is performed up AC power loss with a low battery

code transmitted if power is not returned in approximately 60 hours. After transmitting a

low batter code, the unit bypasses all input circuits to avoid spurious transmission of false

alarms.

DE -6C/12C INS ALLA ION AND OPERA ION MANUAL

DIGI IZE, INC. 700174-0000 REV.D 02/16

1-2

1.3 ACTIVATION OF INPUTS

here are six inputs for the ransmission of Alarms, roubles, Low Battery (if desired)

and for Restore of Condition (if desired). he DE -6C/12C is fully programmable,

allowing for a short to generate a selected code and the number of rounds. he trouble

(an open line on the input) is also programmable, allowing a selected code and number of

rounds to be generated. Each box number transmitted contains the base number (one to

five digits) plus a single suffix digits. his allows transmission of Alarm Codes for either

a short or open line condition at the input zones. he DE -12C uses 2 of the 6 zone

boards.

When a zone input goes into Alarm, the DE -6C/12C will send the code number for the

unit followed by the code that was selected for the zone that went into Alarm.

For example, Zone 2 shorted with the following parameters:

Four rounds box code 1234, zone code 2

12342

As another example: Zone 2 opened with following parameters:

Four rounds box code 1234, zone code 8

12348

he zone code is the last digit following the one to five digit identification code. For

instance, refer to the examples below:

INCOMING BOX 12341 indicates Box 1234, Zone 1

INCOMING BOX 652265 indicates Box 65226, Zone 5

INCOMING BOX 434 indicates Box 43, Zone 4

1.4 REPORTING PRIORITY

Zone 1 is the highest priority. Priority descends in numerical order down to Zone 6,

which would be reported last. In the case of several different conditions happening at

once, alarms are reported first, followed by restores on alarms. rouble conditions (open

circuits) are the next lower level priority, Zone 1 down to Channel 6, followed by restores

on trouble.

DE -6C/12C INS ALLA ION AND OPERA ION MANUAL

DIGI IZE, INC. 700174-0000 REV.D 02/16 1-3

1.5 NUMBER OF ROUNDS

Rounds are individually programmable of each zone of Alarm, rouble and Restore. For

example, four rounds for Alarm and one round for Restore are standard values on the

Master EPROM.

1.6 TRANSMISSION SPEED

he speed of transmission is adjustable over a range from 1/8 to four seconds in steps of

approximately 1/24 second, and is changed by programming the equivalent number on

the EPROM. he standard value on the master EPROM is 1/4 second, with a value of

06, which represents approximately 6/24. See Section 2.2.1, Step 2 for calculation.

1. EPROM 2 C512

A blank 27C512 EPROM is supplied with each DE -6C. he 27C512 EPROM is

programmed using Digitize DE -PROG programmer. he DE -12C is supplied with 2

EPROMS.

1.8 INDICATORS LEDs

“Watch Dog” red LED: Pulses once every four seconds in standby mode and with the

code while transmitting.

“ rouble” yellow LED: Non-latching indication of any existing trouble condition.

“Main Power” Green LED: Illuminates when 14-16 VAC or 24 VDC of the correct

polarity is present on terminals 1 and 2.

“On Line” red LED: Illuminates when the unit activates to transmit with a good line.

his LED will be off when the unit is transmitting to ground with an open line.

1.9 SPECIFICATIONS

1.9.1 Current Consumption

Less than 100mA standby, 170 mA max operating.

1.9.2 Dimensions

DE -6C/ 12C 17” H x 10.63” W x 5.13” D

DE -6C/12C INS ALLA ION AND OPERA ION MANUAL

DIGI IZE, INC. 700174-0000 REV.D 02/16

1-4

1.10 APPLICABLE PUBLICATIONS

National Fire Protection Association (NFPA) standards 72 proprietary, 1221.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung