DIGITIZE RAD-32 Bedienungsanleitung

Digitize, Inc.

158 Edison Road

Lake Hopatcong, New Jersey 07849-2217

Tel: (973) 663-1011 Part Number: 700178-0000

E-mail: info@digitize-inc.com Revision: H

Website:http://www.digitize-inc.com Issue Date: 10/21

RAD-32/64

Installation & Operation Manual

Digitize, Inc.

158 Edison Road

Lake Hopatcong, NJ 07849-2217

The DIGITIZE logo is a registered trademark of Digitize, Inc.

PROPRIETARY NOTICE

AND DISCLAIMER

DIGITIZE, INC.

158 EDISON ROAD

LAKE HOPATCONG, NJ 07849-2217

PH: (973) 663-1011

E-Mail: info@digitize-inc.com

Website: http://www.digitize-inc.com

This manual has been prepared by DIGITIZE, INC. for use by its licensees, distributors and

customers. The information contained herein is the property of DIGITIZE, INC. and may not

be copied, disclosed or reproduced, in whole or in part, without the prior written approval of

DIGITIZE, INC. Any unauthorized disclosure to, or use of the enclosed information by,

unauthorized third persons shall void any and all representations, warranties and obligations

on the part of DIGITIZE, INC.

DIGITIZE, INC. reserves the right to make changes to the specifications and material

contained herein without prior notice. The information and/or examples (including, but not

limited to circuitry, wiring diagrams, programming, the operation or use shown) described in

this manual are intended solely to illustrate the operating principles of the particular product.

They are not a warranty, representation or guarantee that a particular example or use shown

will perform in a particular situation. They are given for illustration purposes only. DIGITIZE,

INC. shall not be responsible, nor does it represent, that any example of illustration will perform

in a particular environment or practice unless it specifically makes a representation to that

effect.

The material set forth herein is for informational purposes only, and DIGITIZE, INC.

assumes no patent liability with respect to any information or illustrations contained herein.

FCC NOTICE

In compliance with Paragraph 15.105 of the FCC Rules and Regulations, the following

notice is provided.

NOTE: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy, and, if not installed and used in accordance with the instruction manual, may cause

interference to radio communications. Operation of this equipment in a residential area is likely

to cause interference, in which case the user will be required to correct the interference at the

owner's expense.

 
DIGITIZE, INC. 700178-0000 REV. H 10/21 i 
Specifications Subject to Change Without Notice 
Table of Contents 
1GENERAL INFORMATION...............................................................................1-1 
 SYSTEM DESCRIPTION.....................................................................................................1-1 
 RAD-32/64 DESCRIPTION..................................................................................................1-1 
 OPTIONS.............................................................................................................................1-1 
1.3.1 MODULATION..............................................................................................................1-1 
1.3.2 ANTENNA ....................................................................................................................1-2 
1.3.3 FREQUENCY...............................................................................................................1-2 
1.3.4 32 ZONE EOL INPUT CARD (P/N 400601-0001).......................................................1-2 
1.3.5 EIGHT-ZONE FORM C RELAY....................................................................................1-2 
 SPECIFICATIONS ...............................................................................................................1-2 
1.4.1 ELECTRICAL ...............................................................................................................1-2 
1.4.2 INPUTS........................................................................................................................1-3 
1.4.3 FUSES .........................................................................................................................1-3 
1.4.4 CONSTRUCTION.........................................................................................................1-3 
1.4.5 DIMENSIONS...............................................................................................................1-3 
1.4.6 WEIGHT.......................................................................................................................1-3 
1.4.7 TEMPERATURE AND HUMIDITY................................................................................1-3 
1.4.8 TRANSMITTER............................................................................................................1-4 
 FCC REQUIREMENTS........................................................................................................1-4 
 APPLICABLE PUBLICATIONS............................................................................................1-4 
2INSTALLATION................................................................................................2-1 
 HANDLING...........................................................................................................................2-1 
 CABINET MOUNTING.........................................................................................................2-1 
2.2.1 SITE PREPARATION...................................................................................................2-1 
2.2.2 DISASSEMBLY PROCEDURE ....................................................................................2-1 
2.2.3 MOUNTING..................................................................................................................2-1 
 WIRING................................................................................................................................2-2 
2.3.1 CONDUIT CONNECTIONS..........................................................................................2-2 
2.3.2 FIELD WIRING.............................................................................................................2-2 
2.3.3 WIRING........................................................................................................................2-2 
 RF TRANSMITTER AND INTERFACE BOARD...................................................................2-2 
2.4.1 GENERAL ....................................................................................................................2-2 
2.4.2 WIRING........................................................................................................................2-3 
 32 ZONE EOL......................................................................................................................2-3 
2.5.1 GENERAL ....................................................................................................................2-3 
2.5.2 INSTALLATION............................................................................................................2-3 
2.5.3 WIRING........................................................................................................................2-3 
 LCD DISPLAY AND KEYBOARD.........................................................................................2-3 
 ASSEMBLY..........................................................................................................................2-3 
3SYSTEM INITIALIZATION................................................................................3-1 
 GENERAL............................................................................................................................3-1 
 ASSEMBLY..........................................................................................................................3-1 
 CONNECTIONS AND SETTINGS .......................................................................................3-1 
3.3.1 ZONE INPUTS .............................................................................................................3-1 
3.3.2 ANTENNA ....................................................................................................................3-1 
 BATTERY INSTALLATION ..................................................................................................3-1 

 
ii DIGITIZE, INC. 700178-0000 REV. H 10/21 
Specifications Subject to Change Without Notice 
 POWER-UP..........................................................................................................................3-1 
5.1 AC ................................................................................................................................3-1 
5.2 DC................................................................................................................................3-1 
4PROGRAMMING..............................................................................................4-1 
 PROGRAM INITIALIZATION................................................................................................4-1 
 PROGRAM ACCESS...........................................................................................................4-1 
 PROGRAMMABLE FUNCTIONS.........................................................................................4-1 
3.1 FUNCTION 0 (SETTING BOX NUMBER)....................................................................4-2 
3.2 FUNCTION 1 (NUMBER OF DIGITS)..........................................................................4-2 
3.3 FUNCTION 2 (NUMBERS OR ROUNDS)....................................................................4-3 
3.4 FUNCTION 3 (CHANGE PASSNUMBER) ...................................................................4-3 
3.5 FUNCTION 4 (SET TIME)............................................................................................4-3 
3.6 FUNCTION 5 (SET FIRST “TEST BOX” TIME)............................................................4-3 
3.7 FUNCTION 6 (SET “TEST BOX” INTERVAL) ..............................................................4-4 
3.8 FUNCTION 7 (SET NUMBER OF CYCLES PER SECOND) .......................................4-4 
3.9 FUNCTION 8 (SET TILT/TAMPER SENSITIVITY).......................................................4-4 
3.10 FUNCTION 9 (ZONE INPUT SENSITIVITY)................................................................4-4 
3.11 FUNCTION 10 (ZONE INPUT SETTLE TIME).............................................................4-5 
3.12 FUNCTION 11 (BEEP WHEN ALARM)........................................................................4-5 
3.13 FUNCTION 12 (BEEP CONTINUOUSLY WHILE IN ALARM) .....................................4-5 
3.14 FUNCTION 13 (BEEP ON AC POWER FAIL)..............................................................4-5 
3.15 FUNCTION 14 (TROUBLE RELAY).............................................................................4-5 
3.16 FUNCTION 15 (SELECT RADIO FORMAT) ................................................................4-6 
3.17 FUNCTION 16 (ALARM TO RELAY)............................................................................4-6 
3.18 FUNCTION 17 (AC POWER FAILURE DELAY) ..........................................................4-6 
3.19 FUNCTION 18 (SEND FIRST PREFIX) .......................................................................4-7 
3.20 FUNCTION 19 (SEND SECOND PREFIX) ..................................................................4-7 
3.21 FUNCTION 20 (PREFIX TONE TO SEND)..................................................................4-7 
3.22 FUNCTION 21 (NUMBER OF TIMESLOTS)................................................................4-7 
3.23 FUNCTION 22 (LOW BATTERY ON AC POWER FAIL)..............................................4-7 
3.24 FUNCTION 23 (PANEL TROUBLE).............................................................................4-8 
3.25 FUNCTION 24 (NUMBER OF ROUNDS FOR TEST TRANSMISSION)......................4-8 
3.26 FUNCTIONS 25-40 (TONE ASSIGNMENTS)..............................................................4-8 
3.27 FUNCTION 41 (TONE ASSIGNMENT, PANEL TROUBLE) ........................................4-9 
3.28 FUNCTION 42 (TONE ASSIGNMENT, TAMPER).......................................................4-9 
3.29 FUNCTION 43 (TONE ASSIGNMENT, BOX TEST) ..................................................4-10 
3.30 FUNCTION 44 (TRANSMITTER TEST).....................................................................4-10 
3.31 FUNCTION 45 (MULTIPLE ZONE TRANSMISSIONS)..............................................4-10 
3.32 FUNCTION 46 (MEMORY RESET)............................................................................4-10 
3.33 FUNCTION 47 (SETTING ZONE DELAYS)...............................................................4-12 
5THEORY OF OPERATION...............................................................................5-1 
 CONTROLS .........................................................................................................................5-1 
1.1 TEST............................................................................................................................5-1 
1.2 READ ...........................................................................................................................5-1 
1.3 IN/OUT.........................................................................................................................5-1 
1.4 CLR/SIL........................................................................................................................5-1 
1.5 BEEPER.......................................................................................................................5-2 
 OPERATING PROCEDURE ................................................................................................5-2 
2.1 GENERAL ....................................................................................................................5-2 
2.2 NORMAL QUIESCENT OPERATION ..........................................................................5-2 
2.3 ALARM CONDITION....................................................................................................5-2 
2.4 TROUBLE CONDITION ...............................................................................................5-2 

DIGITIZE, INC. 700178-0000 REV. H 10/21 iii

Specifications Subject to Change Without Notice

5.2.5 STANDBY POWER OPERATION................................................................................5-3

5.2.6 AC POWER FAIL AND LOW BATTERY......................................................................5-3

6TESTING ..........................................................................................................6-1

GENERAL............................................................................................................................6-1

ACCEPTANCE TESTING ....................................................................................................6-1

7APPENDIX A TONE FREQUENCIES...............................................................7-1

8APPENDIX B TONE ASSIGNMENTS ..............................................................8-1

iv DIGITIZE, INC. 700178-0000 REV. H 10/21

Specifications Subject to Change Without Notice

DIGITIZE, INC. 700178-0000 REV. H 10/21 1-1

Specifications Subject to Change Without Notice

1 GENERAL INFORMATION

SYSTEM DESCRIPTION

The overall system is known as the Digitize Radio Fire Alarm System and consists of a Digitize

SYSTEM 3505 Prism Lx, together with a Digitize Mark 6 Radio receiver. The system can

accommodate both AM (Amplitude Modulated) or FM (Frequency Modulated) radio boxes. A

receiver and antenna are also required at the receiving console location. The maximum

number of Radio Alarm Boxes each console can support is 2000 with the appropriate number

of receivers installed. The overall system is intended for use as a Public Fire Reporting system

per NFPA 1221.

RAD-32/64 DESCRIPTION

The RAD-32 and RAD-64 are microprocessor based coded radio boxes, capable of

monitoring 32 or 64 supervised input points. Input points may be added to the RAD-32 to

make it a RAD-64. Also supervised are AC power,Ground, and Battery Faultconditions. Each

standard model is housed in a painted steel enclosure with a hinged door, and is supplied with

a step-down AC transformer, tamper switch, cam lock, rechargeable battery pack rated for 60

hours and an integral battery charger.

The following assemblies make up a RAD-32/64: LCD display and keyboard P/N 400373-

0000, Microcontroller board P/N 400464-0000, 32 Zone Input Board P/N 400601-0001 (two for

RAD-64), Transformer Assembly P/N 450449-0001, 12 Volt 12 AH battery P/N 900414-0006,

Switching Power Supply P/N 400467-0001, AM transmitter P/N 450387-0001 (72-76 MHz) or

450387-0002 (136-174 MHz) or an FM transmitter P/N 450390-0000.

The Microcontroller board is a microprocessor based controller board. A program that

resides in an EPROM program chip controls all functions of the RAD-32/64. This flexibility in

the product allows the user to select such things as output format, set box number, etc. The

transmitter assembly provides all power output regulation. The transmitter will provide 1-Watt

output even at 10.5 VDC of battery voltage. The AM transmitter has a piggyback tone card to

produce all required tones. The tones are produced via an on-board crystal oscillator and

programmable divider circuits. The transformer assembly provided is used to step down the

120 VAC input voltage to 14 VAC required for proper operation of the RAD-32/64. The sealed

lead acid battery supplied provides the required 12.6 VDC for battery backup. The battery is

a 12 Amp Hour battery and will operate the RAD-32/64 for a minimum of 60 hours during an

AC failure. The LCD and keyboard allows the operator to view Alarm and Trouble information

on a 32-character display. The keypad provides access to field programmable functions for

the RAD-32/64.

OPTIONS

1.3.1 MODULATION

The RAD-32/64 may be ordered for AM or FM operation.

RAD-32/64 INSTALLATION AND USER MANUAL

1-2 DIGITIZE, INC. 700178-0000 REV. H 10/21

Specifications Subject to Change Without Notice

RAD-32 425127-0011, 72-76 MHz, AM

425127-0012, 138-174 MHz, AM

425127-0013, 72-76 MHz, FM

RAD-64 425129-0011, 72-76 MHz, AM

425129-0012, 138-174 MHz, AM

425129-0013, 72-76 MHz, FM

1.3.2 ANTENNA

External Mount 900489-xxxx, 72-76 MHz

900491-xxxx, 138-176 MHz

1.3.3 FREQUENCY

Frequency must be selected when order is placed. RAD-32/64 is available in 72-76 MHz

range and 138-174 MHz range.

1.3.4 32 ZONE EOL INPUT CARD (P/N 400601-0001)

The 32 Zone Input Card provides lightning protection for each zone. Each RAD-32 contains

one 32 Zone EOL card. A RAD-64 contains two cards. The RAD-32 can be expanded to a

RAD-64 at any time.

1.3.5 EIGHT-ZONE FORM C RELAY

The Eight Zone Form C Relay board provides eight non-supervised Form C outputs. Up to

eight relay boards may be added to the RAD-32/64 panels, although additional cabinetry and

power may be necessary. The relay contacts are rated 24 VDC at 1.25 Amp for a resistive

load and 125 VAC at .4 amp for an inductive load.

P/N 400375-0001, 1 Amp

P/N 400375-0002, 5 Amp

SPECIFICATIONS

1.4.1 ELECTRICAL

Primary Power Input 120 VAC

Operating Power Consumption (pri) 150 Milliamps (max.)

Standby Battery (BATT) 12 Volt sealed lead acid

Standby 60 hours

Standby calculations are based on normal operation. During normal operation the RAD-

32/64 test in once each day. The RAD-32/64 draws more power while transmitting. Additional

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Radio Handbücher anderer Marken

EisSound

EisSound KBSound iSelect Bedienungsanleitung

Midland

Midland 1001LWX Bedienungsanleitung

Konig

Konig HAV-SR41 Bedienungsanleitung

Roberts

Roberts exprssion Bedienungsanleitung

VDigi

VDigi DD3.0 Bedienungsanleitung

Radio Shack

Radio Shack 21-1863 Bedienungsanleitung

Roberts

Roberts Stream 207 Bedienungsanleitung

Sony

Sony Walkman SRF-M97 Bedienungsanleitung

Stanley

Stanley FatMax FMC770 Bedienungsanleitung

auna

auna DAB-Radio 10026947 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR190 Bedienungsanleitung

HYT

HYT TC-320 Bedienungsanleitung

B-Tech

B-Tech GMRS-V2 Bedienungsanleitung

Weierwei

Weierwei VEV-V8 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER DAB750 Bedienungsanleitung

Telefunken

Telefunken TF-1505 Bedienungsanleitung

Makita

Makita LXRM03 Bedienungsanleitung

PRESIDENT

PRESIDENT TEDDY R. Bedienungsanleitung