Digitus Biometrics DbServerRackV2 Zero-U Leitfaden

db ServerRack V2 (Zero-U)

Installation Manual

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 2 of 24

Table of Contents

Determining which Lock Pawl to use................................................................................................3

Mounting the Door Interface Box ...................................................................................................5

Mounting the Door Interface Box - Step 1 .........................................................................................5

Mounting the Door Interface Box – Step 2 .........................................................................................6

Mounting the Door Interface Box – Step 3 .........................................................................................7

Mounting the Door Interface Box - Step 4 .........................................................................................8

Mounting the Door Interface Box - Step 5 .........................................................................................9

Mount the Tie Down Pads to the Door and Cabinet ............................................................................ 10

Connect the CAT5 Cable to the Control Unit..................................................................................... 12

Installing the Pawl on the Door Lock.............................................................................................. 14

Using the Tamper Switch Inputs ................................................................................................... 15

Using the Door Contact Inputs..................................................................................................... 17

Using the Alarm Output ............................................................................................................ 19

Using the Wiegand Output......................................................................................................... 20

Using the Door 2 Output ........................................................................................................... 21

Install the 2nd BioLock (Option I)................................................................................................... 21

Install the Electro-Mechanical Lock (Option II)................................................................................... 21

Connecting Power to the Control Unit............................................................................................ 23

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 3 of 24

Determining which Lock Pawl to use

•As all cabinets vary, we offer a wide range to pawls to suit the particular dimensions of your cabinet.

•There are 2 simple measurements that need to be taken to determine which pawl you will need.

•Please obtain the measurements as show in Figure 1 and Figure 2 and contact our electromechanical lock support

team as show below:

Southco Global Cor

orate Head

uarters

Customer Service & Technical Support

Ctr.

Concordville, PA – US

Tel:

(610) 459-4000

Email: [email protected]

Figure 1 Figure 2

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 4 of 24

Mounting the Control Unit

•Mount the db ServerRack v2 Zero-U Control Unit

oThe Control Unit can be attached using the Magnetic Strips for Steel Cabinets or VHB Strips for Aluminum

Cabinets.

oAlternatively, the Control Unit can be placed on a cabinet shelf

•It is preferable to mount the Control Unit near the top of the rack, to ease the running of cables, however this isn't

absolutely necessary.

Figure 3

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 5 of 24

Mounting the Door Interface Box

•If you are installing the db ServerRack Access Control unit to a cabinet that already has a lock installed, remove the

existing lock at this time.

•The "Door Interface Box" provides an interface between the Control Unit and the fingerprint scanner. It also provides

all power and signal connections to the electric lock.

•Install the Door Interface Box as show in Figures 4 thru 9.

Mounting the Door Interface Box - Step 1

•Before removing the double-sided high bond tape from the Door Interface Box, find a suitable location on the inside

of the cabinet door to mount Interface Box.

•Ensure that the selected location will not affect the cabinet door from closing correctly.

•Note that for glass paneled cabinet doors with very narrow frames, the only suitable location may be on the glass.

IMPORTANT:

•Ensure that the Interface Box is located close enough to the lock opening in the door, so that the finger-

sensor on the ribbon cable can go through the door and connect into the lock, see Figure 6.

•Once you have found a suitable location where you intend to mount the Door Interface Box, ensure that the door

surface is clean and free from any debris. (Using neat alcohol to clean the surface is highly recommended. Allow

drying time before proceeding.)

•Remove the protective cover from the double-sided high bond tape located along the edge of the Door Interface

Box.

Figure4

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 6 of 24

Mounting the Door Interface Box – Step 2

•Attach the Door Interface Box to the inside door surface. Only apply a slight amount of pressure to the high bond

tape until you have ensured that the Door Interface Box will not prevent the cabinet door from closing.

•Once you have ensured that the door will close properly and the finger sensor can attach to the lock, apply more

pressure to the high bond tape. The more pressure applied, the greater the bond.

Figure 5

* Open slot for lock. 25mm x 150mm (typical)

IMPORTANT:

Ensure that the Interface Box is located

close enough to the lock opening in the

door, so that the finger-sensor on the

ribbon cable can go through the door

andconnectintothelock,seeFigure6.

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 7 of 24

Mounting the Door Interface Box – Step 3

•Push the finger-sensor assembly through the door lock opening as shown in Figure 6.

•Attach the finger-sensor assembly into the back of the door lock as show in Figure 7. Ensure that the angle of the

finger-sensor assembly and the angle of the door lock are as shown in Figure 7.

Figure 6 Figure 7

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 8 of 24

Mounting the Door Interface Box - Step 4

•Situate the lock on the outside of the cabinet door, so that the ribbon cable attached to the finger-sensor assembly

is at the top of the locking opening. (See Figure 8)

Figure 8

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 9 of 24

Mounting the Door Interface Box - Step 5

•Secure the lock to the door using the Top Mounting Bracket and Bottom Mounting Bracket as show in Figure 9. Do

not over-tighten the screws in the Bottom Mounting Bracket as this may jam the lock mechanism.

•Attach the lock wire coming out of the Door Interface Box to the back of the lock as shown in Figure 8. The wire will

only plug in one way.

Figure 9

Model: db ServerRack V2 Zero-U Digitus Biometrics, Inc. 2011

Page 10 of 24

Mount the Tie Down Pads to the Door and Cabinet

•The Tie Down Pads are used to secure the CAT5 cable that connects the Door Interface Box to the Control Unit.

•Ensure that the door surface is clean and free from any debris. (Using neat alcohol to clean the surface is highly

recommended. Allow drying time before proceeding.)

•Remove the protective cover from each Tie Down Pad and situate as shown in Figure 10.

Figure 10

Inhaltsverzeichnis

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

Digitus Biometrics dbServerRackV2 Zero-U Leitfaden

Beliebte Controller Handbücher anderer Marken