Digitus USR-190017 Bedienungsanleitung
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
1 of 14
Document Information
Reference
USR
-
19001
7
Title
dbDualLock
(S)
Installation/User Guide
Synopsis
dbDualLock
(S)
Installation/User Guide
Author
Chris Marsden
Creation Date
2019
-
Mar
-
2
2
Revisions
Rev
Date
Who
Notes
00
1
2019
-
Mar
-
2
2
Chris Marsden
Init
ial document
002
2019
-
Mar
-
26
David Montgomery
Add details re: lockdown LED sequence
003
2019
-
Oct
-
02
David Montgomery
Fix Typo
’
s
This manual, as well as the software described in it, is furnished under license and may be used or copied only in
accordance with the term of such license. The content of this manual is furnished for informational use only, is subject
to change without notice, and should not be construed as a commitment by Digitus Biometrics, Inc. (Digitus). Digitus
assumes no responsibility or liability for any errors or inaccuracies that may appear in this documentation. Except as
permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of
Digitus.
©2005-2019 Digitus Biometrics, Inc. All rights reserved.
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
2 of 14
dbDualLock (S)
Ergonomic Design
Modularized
Reader Head
Tri color (Red /
Amber / Green)
Reader LED
Tri color (Red /
Magenta / Blue)
Status LED
Secure key
-
cylinder.
Compatible with ultra-
secure cylinders
Optical Handle
Position Sensor
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
3 of 14
Contents
dbDualLock (S) Installation...................................................................................................................................................... 4
Determining which Lock Pawl to use .................................................................................................................................. 4
Mounting the dbDualLock (S) ............................................................................................................................................. 5
Installing the Rotation Limiter ............................................................................................................................................ 6
Positioning the Tie-Down Pads ........................................................................................................................................... 7
Routing the Lock Cable ....................................................................................................................................................... 8
Connecting to dbRemote Node / dbSentry ........................................................................................................................ 9
Connecting to 3rd Party Access Panels .............................................................................................................................. 10
Connecting Latch Position to 3rd Party Panel ................................................................................................................... 11
Power Up............................................................................................................................................................................... 12
Updating Firmware ............................................................................................................................................................... 12
Connected to a dbSentry or dbRemote Node .................................................................................................................. 12
Connected to a 3rd-party Access Panel ............................................................................................................................. 12
Configuration Cards .............................................................................................................................................................. 12
Handle Configuration Card................................................................................................................................................ 12
RFID Configuration Card.................................................................................................................................................... 12
Reader LED ............................................................................................................................................................................ 13
Connected to dbSentry or dbRemote Node ..................................................................................................................... 13
Connected to an Access Control Panel ............................................................................................................................. 13
Status LED ............................................................................................................................................................................. 14
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
4 of 14
dbDualLock (S) Installation
Determining which Lock Pawl to use
As all cabinets vary, we offer a wide range to pawls to suit the particular dimensions of your cabinet.
There are 2 simple measurements that need to be taken to determine which pawl you will need.
Please obtain the measurements as show in Figure 1 and Figure 2 below and contact our support team at
support@digitus-biometrics.com
Figure 1
–
Measurement 1
Edge of Door Frame to Center of Handle
Figure 2
–
Measurement 2
Rear surface of handle to Inside of Door Frame
In most situations the pawl from the existing mechanical handle can be re
-
used with the new lock.
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
5 of 14
Mounting the dbDualLock (S)
If you are installing the dbDualLock (S) into a cabinet that already has a handle / lock installed, remove it.
Secure the dbMultiCardLock (S) to the door using the top and bottom mounting brackets, being careful not to
over tighten the screws as this could cause the lock mechanism to jam.
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
6 of 14
Installing the Rotation Limiter
Figure
2
–
Rotation Limi
ter
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
7 of 14
Positioning the Tie-Down Pads
The second step is to mount the tie-down pads to the cabinet and the cabinet door as illustrated below.
The tie-down pads are used to secure the supplied cable that connects the lock directly to the Remote Node / db Sentry
or Access Control panel.
Ensure that the door surface is clean and free from any debris. Use rubbing alcohol to clean the surface is highly
recommended and allow sufficient time for the cleaned areas to dry before mounting the tie-down pads.
Figure
3
–
Positioning the tie
-
down pads
Remove the protective cover from each tie-down pad and situate as shown in Figure 3.
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
8 of 14
Routing the Lock Cable
Route the cable between the lock and the Remote Node / db Sentry Controller or ACM Panel.
Route the lock cable to the door hinge as illustrated below and secure the cable to the tie-down pads using the supplied
cable-ties. Connect the supplied device cable to the RJ-45 coupler and route it to:
the Remote Node or Sentry (if you are using Digitus a controller)
3rd Party Access Panel (if you are connecting to a third-party access control panel, connect a network cable to RJ-
45 coupler and run back to panel.
Figure
4
–
Routing the cable
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
9 of 14
Connecting to dbRemote Node / dbSentry
Connect the cable to the dbRemote Node / dbSentry Controller.
Handles / locks are connected to the dbRemote Node or dbSentry socket circled in the diagram below.
Each dbRemote Node / dbSentry Controller has two device inputs, Dev 1 and Dev 2.
Figure
5
-
Side View of
db
Remote Node
Figure
6
-
Side View of dbSentry
For clarity and consistency, it is recommended that for a cabinet with 2 doors, the front door is connected to Dev 1 and
the back door is connected to Dev 2.
Document Ref
USR-190017
Document Title
dbDualLock (S) Installation/User Guide
Page
10 of 14
Connecting to 3rd Party Access Panels
Connect the lock to 3rd-party Access Panel
Figure
7
Color
Control
Notes
Orange / White
GND
Ground
Orange
LOCK CTRL
Requires a 12V (24V if a 24V version of the
dbDualLock
was purchased) control line to
unlock the handle
Green / White
RED LED
NC
Blue
V+
Requires a 12VDC Supply
Bl
ue / White
LATCH POS
(used to indicate if the lock is open or closed)
–
Will be pulled to Ground (GND) if the
handle is closed. Will be open circuit if the handle is open. See diagram below
Green
GREEN LED
NC
Brown / White
DATA1
Wiegand Data 1
Brown
DAT
A0
Wiegand Data 0
Inhaltsverzeichnis
Andere Digitus Controller Handbücher
