Digitus DN-80069 Bedienungsanleitung
8-Port 10/100Mbps
Ethernet Unmanaged Switch
Quick Installation Guide
DN-80069
2
Copyright Statement
Our company reserves all copyrights of this document. Any
reproduction, excerption, backup, modification, transmission,
translation or commercial use of this document or any portion of
this document, in any form or by any means, without the prior
written consent of our company is prohibited.
Exemption Statement
This document is provided "as is". The contents of this document
are subject to change without any notice. Please obtain the latest
information through our company website. Our company
endeavors to ensure content accuracy and will not shoulder any
responsibility for losses and damages caused due to content
omissions, inaccuracies or errors
1. Product Introduction
The 8-Port 10/100 Mbps Network switch from DIGITUS® provides
5 x RJ45 ports with 10/100Mbps bandwidth each. Easily expand
the existing network. No configuration is required on the switch
itself; thanks to auto-negotiation and Auto MDI/MDI-X, cables
and speeds are also automatically detected. The switch can be
used as a desktop variant or mounted on a wall. Thanks to the
external power supply, the switch does not need a fan at all. Ideal
for expanding / setting up small home or company network.
3
1.1 Features
8 x RJ45 ports 10/100 Mbps
All ports support 10/100 Mbps bandwidth
Network standards: IEEE 802.3i, IEEE 802.3u,
IEEE802.3x, IEEE802.3az
Full-duplex flow control IEEE802.3x
Store and forward mode operates
Auto-negotiation / Auto-MDI/MDI-X
No configuration necessary
LED indicators for monitoring power, link/activity
1.2 Package Contents
Before installing the Switch, make sure that the following the
"packing list" listed OK. If any part is lost and damaged, please
contact your local agent immediately. In addition, make sure that
you have the tools install switches and cables by your hands.
1 x 8-Port Fast Ethernet Network Switch
1 x Power Supply
1 x Quick Start Guide
4
1.3 Hardware Specifications
Standards
IEEE802.3i, IEEE802.3u, IEEE802.3x,
IEEE802.3az
Interface
8 x 10/100Mbps
Auto-Negotiation ports
Network Media
10BASE-T: UTP category 3,4,5 cable
(maximum 100m)
100BASE-T: UTP category 5, 5e cable
(maximum 100m)
MAC Address Table
1K
Indicators
Per Device
Power: Green
Per Port
10/100Mbps Link / Act: Green
Switching Capacity
1.6Gbps
Packet Buffer
448Mbit
Packet Forwarding Rate
745Kpps
Jumbo Frame
1552Bytes
Power Supply
DC 5V/550mA
(External power adapter supply)
Power Consumption
Maximum: 1.40W(5V DC)
Dimensions (W x D x H)
140*67*26mm
Environment
Operating Temperature: 0°C - 40°C
Storage Temperature: -40°C - 70°C
Operating Humidity:
10%~90% non-condensing
Storage humidity:
5%~90% non-condensing
5
1.4 External Component Description
Upper Panel
The upper panel of the Switch consists of a series of LED
indicators
LED indicators:
The LED Indicators will allow you to monitor, diagnose and
troubleshoot any potential problem with the Switch, connection
or attached devices.
The following chart shows the LED indicators of the Switch along
with explanation of each indicator.
LED Indicator
Faceplate
Marker
Status Indication
Power Indicator Power
Off Power Off.
Solid
green
Power On.
10/100 BASE-T
adaptive
Ethernet port
indicators
(1-8)
Link/Act
Off Power Off.
Solid
green
Power On.
Blinking
The port is
transmitting or
receiving data.
6
Front Panel
The front panel of the Switch, contains of 8 x
10/100Mbps RJ-45 ports
10/100 Mbps RJ-45 ports (1~8):
Designed to connect to the device with a bandwidth of 10Mbps,
100Mbps. Each has a corresponding Link/Act indicator.
Rear Panel
The rear panel of the Switch consists of one Grounding Terminal
and a 5V DC power adapter interface
Grounding Terminal:
Located on the left side of the rear panel, use wire grounding to
lightning protection.
DC Power Connector:
Located on the right side of the rear panel, power supply via
external power adapter, using 5V/550mA external power supply.
7
2. Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make
connections to it. Please read the following topics and perform
the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect
installation causing device damage and security threat.
Put the Switch on stable place or desktop in case of
falling damage.
Make sure the Switch works in the proper DC input range
and matches the voltage labeled on the Switch.
To keep the Switch free from lightning, do not open the
Switch's shell even in power failure.
Make sure that there is proper heat dissipation from and
adequate ventilation around the Switch.
Make sure the cabinet to enough back up the weight of
the Switch and its accessories.
2.2 Desktop Installation
Sometimes users are not equipped with the 19-inch standard
cabinet. So when installing the Switch on a desktop, please attach
these cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow
adequate space for ventilation between the device and the
objects around it.
8
2.3 Wall Installation
The Switch can also be installed on a wall. Two installing slots are
provided on the bottom of the Switch for this purpose. Please
make sure that the front panel is exposed in order to view the
LEDs. Please refer to the illustration below:
Step one:
Please drill two suitable
holes, press two expansion
tubes into the two holes
respectively.
Step two:
Insert the screw into the
expansion tube.
Step three:
Hang the switch on the two
screws.
Step four:
Installation is completed.
9
2.4 Power on the Switch
The Switch is powered on by the External DC adapter 5V/500mA
power supply.
Please follow the next tips to connect:
Use the standard DC adapter to connect one end of the power
socket to the power DC interface of the back panel of the switch.
And check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.5 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network
card driver, please connect one end of the twisted pair to RJ-45
jack of your computer, the other end will be connected to any RJ-
45 port of the Switch, the distance between Switch and computer
is around 100 meters. Once the connection is OK and the devices
are power on normally, the LINK/ACT status indicator lights
corresponding ports of the Switch.
Hereby Assmann Electronic GmbH, declares that the Declaration
of Conformity is part of the shipping content. If the Declaration of
Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Inhaltsverzeichnis
Andere Digitus Schalten Handbücher
Digitus
Digitus DA-70135-3 Bedienungsanleitung
Digitus
Digitus DC-OC-12U Bedienungsanleitung
Digitus
Digitus DN-652120 Bedienungsanleitung
Digitus
Digitus DN-650107 Bedienungsanleitung
Digitus
Digitus DC IC612I Bedienungsanleitung
Digitus
Digitus DS-12883 Bedienungsanleitung
Digitus
Digitus DS-11402-1 Bedienungsanleitung
Digitus
Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Bedienungsanleitung
Digitus
Digitus DN-80201 Bedienungsanleitung
Digitus
Digitus DN-60021-1 Bedienungsanleitung
Digitus
Digitus DN-651132 Bedienungsanleitung
Digitus
Digitus DN-95347 Bedienungsanleitung
Digitus
Digitus DA-70241 Bedienungsanleitung
Digitus
Digitus DS-45329 Bedienungsanleitung
Digitus
Digitus DN-80064-1 Bedienungsanleitung
Digitus
Digitus DS-45311 Bedienungsanleitung
Digitus
Digitus DS-45316 Bedienungsanleitung
Digitus
Digitus DS-12423 Bedienungsanleitung
Digitus
Digitus DA-70223 Bedienungsanleitung
Digitus
Digitus DN-80212 Bedienungsanleitung
