Digitus DN-95347-1 Bedienungsanleitung

16 Port Gigabit PoE Switch,

19 Inch, Unmanaged,

2 SFP Uplink

Quick Installation Guide

DN-95347-1

1. Introduction

The DIGITUS 16-Port Gigabit Rack mount Switch with sixteen Power over Ethernet ports

and two additional SFP Fiber Port, offers your network significant improvement in

terms of performance and efficiency. Thanks to PoE support, you only need a single

(network) cable for power and data transfer. This switch makes it much easier to

connect devices such as access points, network cameras, and IP telephones, and

requires far less cabling than alternatives. It also allows you to extend your network in

places where there are no power supply cables or sockets available. The switch does

not require any configuration and therefore guarantees quick and seamless integration

into the network. Moreover, can be manually switched to a Normal mode, or Flow

Control mode, or VLAN mode to suitable for various occasions flexibly. Based on Gigabit

Ethernet Technology, it is essential to helping solve network bottlenecks that frequently

develop as more advanced computer users and newer applications continue to demand

greater network resources.

2. Features

Comply with IEEE 802.3i, IEEE 802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x,

IEEE802.3az standards

Support IEEE802.3af, IEEE802.3at standards

Supporting Normal mode, VLAN mode and Extend mode, flexible to switch

The maximum output power of a single port is 30W, and the total output power of

PoE is 247W.

16 x 10/100 /1000 Mbps self-adaptive RJ45 ports, support port auto flip (Auto MDI /

MDIX)

Flow control method: Full-duplex adopts IEEE 802.3x standard, half-duplex adopts

Backpressure standard.

Support MAC address self-learning

The UTP port supports the auto-negotiation function and automatically adjusts the

transmission mode and transmission rate

Use store-and-forward architecture

3. Package Contents

1x 16 Port Gigabit PoE Switch, 19 Inch,

Unmanaged, 2 SFP Uplink

1x Power Cable

1x QIG

4. Specifications

Interfaces

16*10/100/1000Mbps Adaptive Ethernet port

2*100/1000Mbps SFP port

SFP port

Support 1000Base-X

Working Mode

Normal mode

（Switch all ports can communicate with each other）

Flow Control mode

(All ports' flow control functions are disable)

VLAN mode (1 to 16 cannot communicate with each

other, but can communicate with 17F-18F)

Power Supply

AC (AC) Input:

Rated voltage range: 100-240V~

Maximum voltage range: 90-264V~

Frequency: 50 -60 hz

Rated current: 3.5A

PoE

Support IEEE 802.3AF and IEEE 802.3AT

Single port PoE maximum output power 30W,

The whole machine support PoE maximum output

power 247W.

The output voltage of PoE power supply port is 54V.

Power Pin Assignment

1/2(+),3/6(-)

Power Consumption

Maximum (PoE on): 297W

Operating Temperature

0ºC ~ 45ºC

Storage Temperature

-40ºC ~ 70ºC

Operating Humidity

10% ~ 90% RH

Storage humidity

5% ~ 90% RH

Fan

Support

Dimensions (W x D x H)

440*208*44mm

Switching Capacity

36Gbps

5. External Component Description

The front panel consists of 16*10/100/1000Mbps Adaptive Ethernet port, 2*1000Mbps

SFP port, 1*Mode switch, a series of LED indicators. The rear panel provides an AC power

connector, a Ground Terminal. Its appearance is shown below:

Front Panel

The front panel consists of LED indications and network ports.

PWR indicator

10/100/1000Base-T Link/Act indicator

Mode switch

10/100/1000Base-T Adaptive Ethernet port

SFP port

Real Panel

The rear panel view of the Switch consists of an AC power connector.

Ground Terminal

AC power connector

Power Supply

Rated voltage range: 100-240V~

Frequency: 50 to 60 Hz

Cooling Solution

The switch adopts turbo fan for ventilation to ensure that the equipment can work

normally under the specified environment. When placing the case, leave enough space of

10cm on both sides of the case and the rear panel to facilitate air circulation.

PD power supply wiring

The PoE power supply design supports the iEEE802.3af and 802.3at power supply

standards, and uses Alternative a mode power supply, that is, 12+, 36- power supply in

the standard Ethernet port.

Indicator

Faceplate

Marker

Status

Indication

PWR Status

Light

PWR

Off

Power Off.

Solid green

Power On.

Ethernet port

indicator

Link/ACT

(1-16)

Off

The port is NOT connected.

Solid orange

The port is connected at

10/100Mbps.

Blinking

The port 10/100M data transceiver.

Solid green

The port is connected at

1000Mbps.

Blinking

The port 1000M data transceiver.

SFP port

indicator

Link/ACT

(17F-18F)

Off

The port is NOT connected.

Solid orange

The port is connected at 100Mbps.

Blinking

The port 100M data transceiver.

Solid green

The port is connected at

1000Mbps.

Blinking

The port 1000M data transceiver.

PoE status

indicators

PoE

(1-16)

Off

The port PoE is not powered.

Solid green

Power supply to port PoE normal.

Blinking

The port PoE overloaded

6. Installing and Connecting the Switch

This part describes how to install your Ethernet Switch and make connections to it.

Please read the following topics and perform the procedures in the order being

presented.

6.1 Installation

Please follow the following instructions in avoid of incorrect installation causing device

damage and security threat.

Put the Switch on stable place or desktop in case of falling damage.

Make sure the Switch works in the proper AC input range and matches the voltage

labeled on the Switch.

To keep the Switch free from lightning, do not open the Switch's shell even in power

failure.

Make sure that there is proper heat dissipation from and adequate ventilation around

the Switch.

Make sure the cabinet to enough back up the weight of the Switch and its

accessories.

6.1.1 Desktop Installation

Sometimes users are not equipped with the 19-inch standard cabinet. When installing

the Switch on a desktop, please attach these cushioning rubber feet provided on the

bottom at each corner of the Switch in case of the external vibration. Allow adequate

space for ventilation between the device and the objects around it.

6.1.2 Rack-mountable Installation in 19-inch Cabinet

The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed in

a wiring closet with other equipment. To install the Switch, please follow these steps:

1) Attach the mounting brackets on the Switch's side panels (one on each side) and

secure them with the screws provided.

2) Use the screws provided with the equipment rack to mount the Switch on the rack

and tighten it.

6.1.3 Power on the Switch

The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power

supply. Please follow the next tips to connect:

AC Electrical Outlet:

It is recommended to use single-phase three-wire receptacle with neutral outlet or

multifunctional computer professional receptacle. Please make sure to connect the metal

ground connector to the grounding source on the outlet.

AC Power Cord Connection:

Connect the AC power connector in the back panel of the Switch to external receptacle

with the included power cord, and check the power indicator is ON or not. When it is ON,

it indicates the power connection is OK.

6.2 Connect Computer (NIC) to the Switch

Please insert the NIC into the computer, after installing network card driver, please

connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be

connected to any RJ-45 port of the Switch, the distance between Switch and computer is

around 100 meters. Once the connection is OK and the devices are power on normally,

the LINK status indicator lights corresponding ports of the Switch.

6.3 Switch connection to the PD

1-16 ports of the Switch have PoE power supply function, the maximum output power up

to 30W each port, it can make PD devices, such as internet phone, network camera,

wireless access point work. You only need to connect the Switch PoE port directly

connected to the PD port by network cable.

CE Mark Warning: This is a Class A product. In home environment, this product may cause

radio interference. In this case, the user may be required to take appropriate measures.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of

the shipping content. If the Declaration of Conformity is missing, you can request it by

post under the below mentioned manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3, 58513 Lüdenscheid, Germany

Inhaltsverzeichnis

Andere Digitus Schalten Handbücher

Digitus

Digitus DS-45339 Bedienungsanleitung

Digitus

Digitus DN-80111 Bedienungsanleitung

Digitus

Digitus DS-12860 Bedienungsanleitung

Digitus

Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Bedienungsanleitung

Digitus

Digitus DS-11402-1 Bedienungsanleitung

Digitus

Digitus DN-95140 Bedienungsanleitung

Digitus

Digitus DA-70220 Bedienungsanleitung

Digitus

Digitus DN-80068 Bedienungsanleitung

Digitus

Digitus DN-80233 Bedienungsanleitung

Digitus

Digitus DN-651113 Bedienungsanleitung

Digitus

Digitus DA-70235 Bedienungsanleitung

Digitus

Digitus DS-11200-1 Bedienungsanleitung

Digitus

Digitus DA-70245 Bedienungsanleitung

Digitus

Digitus DN-95104 Bedienungsanleitung

Digitus

Digitus DA-70223 Bedienungsanleitung

Digitus

Digitus DA-70241-1 Bedienungsanleitung

Digitus

Digitus DA-70247 Bedienungsanleitung

Digitus

Digitus DS-12423 Bedienungsanleitung

Digitus

Digitus DS-12820 Bedienungsanleitung

Digitus

Digitus DS-45329 Bedienungsanleitung

Digitus

Digitus DN-651126 Bedienungsanleitung

Digitus

Digitus DS-45333 Bedienungsanleitung

Digitus

Digitus DS-13112 Bedienungsanleitung

Digitus

Digitus DN-651154 Merkblatt

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung