Digitus DN-170120 Bedienungsanleitung

UPS BATTERY MODULE

Manual

DN-170120/ DN-170121/

DN-170122/ DN-170123

Table of Contents

1. Introduction......................................................................... 4

2. Package Content.................................................................. 4

3. Safety Warnings................................................................... 4

4. Rear Panel Description ........................................................ 5

5. Installation ........................................................................... 5

6. Operation............................................................................. 8

7. Maintenance........................................................................ 8

8. Testing New Batteries........................................................ 12

9. Specifications (for with charger model) ............................ 13

Special Symbols

The following are examples of symbols used on the UPS or

accessories to alert you to important information:

RISK OF ELECTRIC SHOCK – Observe the warning

associated with the risk of electric shock symbol.

CAUTION: REFER TO OPERATOR'S MANUAL –

Refer to your operator's manual for additional

information, such as important operating and

maintenance instructions

This symbol indicates that you should not discard

the UPS or the UPS batteries in the trash. This

product contains sealed, lead-acid batteries and

must be disposed of properly. For more

information, contact your local recycling/ reuse or

hazardous waste center.

This symbol indicates that you should not discard

waste electric al or electronic equipment (WEEE)

in the trash. For proper disposal, contact your

local recycling/ reuse or hazardous waste center.

1. Introduction

The extended battery pack can be added to UPS to extend the

available battery time. Up to four EBPS can be installed with the

ups.

2. Package Content

Check the accessories according to the packing list and contact

the dealer in case of missing parts.

•1x Battery Pack

•1x User Manual

•1x AC input cord

•1x Plastic base

•1x EBP Cable

3. Safety Warnings

IMPORTANT SAFETY IN STRUCTIONS – SAVE THESE IN

STRUCTIONS

This manual contains important instruct icons that you should

follow during installation and maintenance of the EBP. Please

read all instruct icons before operating the equipment and save

this manual for future reference.

CAUTION

•Batteries can present a risk of electrical shock or burn from

high short-circuit current. Observe proper precautions.

Servicing should be performed by qualified service

personnel knowledgeable of batteries and required

precautions. Keep unauthorized personnel away from

batteries.

•Proper disposal of batteries is required. Refer to your local

codes for disposal requirements.

•Never dispose of batteries in a fire. Batteries may explode

when exposed to flame.

4. Rear Panel Description

GND screw hole

AC input socket

Breaker

SBS50 terminal

5. Installation

Inspecting the

Equipment

If any equipment has been damaged during shipment, keep the

shipping

cartons and packing materi

s for the carrier or place

rchase and

file

a claim for

shi

pping damage. If you

disc

over

damage after

acceptance,

file a claim for concealed

damage.

To install the optional EBP(s) for a UPS:

1. Remove the front cover of each EBP. Press the panel side,

hold the other side, and quickly extract it, then extract the

other side with display.

2. Remove the front cover of UPS.

Press the panel side with LCD display, hold the other side

and quickly extract it, and then extract the other side with

display. A ribbon cable connects the LCD control panel to

the UPS. Do not pull on the cable or disconnect it. When

remove the panel, operate as the following below Figure

shows instead of the left one.

It is wrong that extracting the front cover from the

handle.

It is correct that extracting the front cover from the

panel.

3. On the bottom of the UPS front cover, remove(A) the EBP

cable knockout.

4. Plug the EBP cable(s) into the battery connector(s)

•A small amount of arcing may occur when connecting

an EBP to the UPS. This is normal and will not harm

personnel. Insert the EBP cable into the UPS battery

connector quickly and firmly. Connect red to red, black

to black, and yellow to yellow. Press the two parts

tightly together to ensure a proper connection.

•To connect a second EBP, unclip the EBP connector on

the first EBP and pull gently to extend the wiring to the

EBP connector on the second EBP. Repeat for any

additional EBPS.

•Another kind of connection is, can pass from the rear

panel of the EBP SBS50 terminal received UPS and

parallel to the other EBP, pay attention to the positive

and negative electrodes.

Note: Up to four EBPS may be connected to the UPS.

Front panel

Rear panel

5. Verify that the EBP connections are tight, and that

adequate bend radius and strain relief exist for each cable.

6. Replace the EBP front cover.

•To replace the cover, verify that the EBP cables are

routed through the EBP cover knockouts, cover

connects with the cover hook near the left side of the

EBP cabinet. Repeat for each additional EBP.

•Put the front panel side with display to the panel port,

put another side to the other two ports, then press it

until the panel and the chassis are combined tightly.

7. Verify that all wiring connecting the UPS and EBP(s) is

installed behind the front covers and is inaccessible to

users.

6. Operation

Configuring Battery Settings

Set the UPS for the number of EBPs installed.

To ensure maximum battery runtime, configure the UPS for the

correct number of EBPs, refer to below Table for the appropriate

setting of battery numbers and type. Use the up and down

buttons to select the number of battery strings according to your

UPS configuration.

All UPS and EBP Cabinets

Number of Battery Strings

UPS only (internal batteries)

（

default

）

UPS+1EBP

UPS+2EBPs

UPS+3EBPs

UPS+4EBPs

NOTE: The UPS contains one battery string; each EBP contains

two battery strings.

7. Maintenance

Replacing Batteries

NOTE: DO NOT D ISCONNECT the batteries while the UPS is in

Battery mode.

•The EBP can be replaced when UPS is ON but be aware that

if the utility fails at that time, the load of the UPS may NOT

be protected.

•For safety, suggest removing input power before changing

the batteries.

WARNING

•Service should be performed by qualified service personnel

knowledgeable of batteries and required precautions. Keep

unauthorized personnel away from batteries.

•Batteries can present a risk of electrical shock or bum from

high short circuit current. Observe the following precautions.

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Do not lay tools or metal parts on top of batteries.

4) Wear rubber gloves and boots.

•When replacing batteries, replace with the same type and

number of batteries or battery packs. Contact your service

representative to order new batteries.

•Proper disposal of batteries is required.

•Refer to your local codes for disposal requirements.

•Never dispose of batteries in a fire. Batteries may explode

when exposed to flame.

CAUTION

The EBP is heavy. Lifting

the

cabinet requires a minimum of

two people.

1. If the battery fault, the following steps are provided for

modular unit to replace the new battery pack.

2. Remove the front panel of the battery box.

3. Remove the connection cables between battery box and

UPS. Release the screw of the baffle of the battery pack.

Remove the baffle from the left.

M4x8 Pan-Head

Screws (2 places)

Insert the thin-wall into the slot

4. Grasp the handle in front of the battery pack, take out of

it and hold it, then remove the battery pack.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus UPS Handbücher

Digitus

Digitus DN-170108 Bedienungsanleitung

Digitus

Digitus DN-170041 Bedienungsanleitung

Digitus

Digitus DN-170100-1 Bedienungsanleitung

Digitus

Digitus DN-170110 Bedienungsanleitung

Digitus

Digitus DN-170095 Bedienungsanleitung

Digitus

Digitus DN-170013 Bedienungsanleitung

Digitus

Digitus DN-170093 Bedienungsanleitung

Digitus

Digitus DN-170063 Bedienungsanleitung

Digitus

Digitus DN-170010 Bedienungsanleitung

Digitus

Digitus DN-170106 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung