DIMAT TPU-1 Betriebsanleitung

Communication solutions for power utilities

1/69

DIMAT

Antonio Machado,78-80 08840

Viladecans, Barcelona-Spain

Tel.: +34 933 490 700

Fax: +34 933 492 258

Mail to: ziv@zivautomation.com

www.zivautomation.com

UNIVERSAL TELEPROTECTION

TPU-1

INSTALLATION AND COMMISSIONING MANUAL

Web version TPU-1R

Rev. 5.9 - May 2018

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

2/69



SAFETY SYMBOLS



WARNING OR CAUTION:

This symbol denotes a hazard. Not following the indicated procedure,

operation or alike could mean total or partial breakdown of the

equipment or even injury to the personnel handling it.

NOTE:

Information or important aspects to take into account in a procedure,

operation or alike.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

3/69

TABLE OF CONTENTS

Page

INTRODUCTION 5

1MECHANICAL CHARACTERISTICS 6

1.1 SHELF MODULE CAPACITY 7

1.2 REPLACING THE MODULES 8

2FRONT PLATE ELEMENTS 9

3INTERNAL SETTINGS 11

3.1 PROCESSING MODULE 11

3.2 PROTECTION-SIDE INTERFACE MODULES

(CIRCUITS FROM ONE TO TWO COMMANDS) 12

3.3 DIGITAL LINE INTERFACE MODULE 14

3.4 DIGITAL SIGNAL I/O INTERFACE MODULE (DSTU) 17

4CONNECTIONS 18

4.1 POWER SUPPLY 19

4.2 PROCESSING MODULE 20

4.3 LINE INTERFACE MODULES 21

4.3.1 IETU module 21

4.3.2 IDTU module 24

4.3.3 IOTU module 25

4.3.4 IOCT module 26

4.3.5 IPIT module 27

4.3.6 IATU and IBTU modules 28

4.4 PROTECTION-SIDE INTERFACE MODULE

(CIRCUITS FROM ONE TO TWO COMMANDS) 29

4.5 GOOSE PROTECTION INTERFACE MODULE 30

4.6 RELAY INTERFACE MODULES 31

4.7 MODULES FOR TELESIGNALLING AND REMOTE MEASUREMENTS 32

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

4/69

Page

5COMMISSIONING PROCEDURE 34

5.1 CHECKS 34

5.2 MODULE CONFIGURATION 34

5.3 STARTING UP THE TERMINAL 35

5.4 CONFIGURATION OF THE WEB SERVER 35

5.5 CONFIGURATION OF THE MANAGEMENT COMPUTER 35

5.5.1 Characteristics of the management computer 36

5.5.2 Connections 36

5.5.3 Configuration 39

5.6 STARTING UP THE WEB SERVER 40

5.7 CERTIFICATE OF AUTHENTICITY 42

5.8 LEAVING THE WEB MANAGEMENT 42

5.9 ON-LINE WEB MANAGEMENT AND OFF-LINE WEB MANAGEMENT 42

5.10 UPDATING THE WEB SERVER PAGES 43

6MAINTENANCE 44

7TRANSPORT AND STORAGE 47

7.1 TRANSPORT 47

7.2 STORAGE 48

APPENDIX A

IP ADDRESSING 49

APPENDIX B

IEC 61850 STANDARD 52

APPENDIX C

CABINET-MOUNTING TERMINAL BLOCKS 54

APPENDIX D

OPTIONAL LCD DISPLAY 66

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

5/69

INTRODUCTION

This manual describes the installation and commissioning procedure for the TPU-1

universal teleprotection terminal.

Firstly, it indicates the mechanical characteristics of the terminal and how to replace the

modules without damaging either the modules or the terminal. It goes on to describe the

function of the optical indicators on the front plate and shows the position and function of the

internal jumpers that can be configured by the user. It then describes the external

connections of both the power supply and the signals.

Finally, it deals with the commissioning procedure, which begins with a series of checks. It

then describes the connection of the PC followed by how to start up the equipment and the

Management System.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

6/69

1 MECHANICAL CHARACTERISTICS

The TPU-1 terminal is made up of a 19” shelf that is 3 standard units (s.u.) in height,

prepared for rack mounting.

Figure 1 shows the general dimensions of the shelf as well as the position of the fastening

holes. As can be seen in the figure, the shelf has one ventilation grid.

Figure 1 General dimensions of the TPU-1 shelf

The input and output of signals is carried out by means of the plug-in connectors located at

the rear of the shelf. If one wishes the external connections to be carried out through a

cabinet-mounting terminal block, it can be supplied on request, together with the necessary

cables, see Appendix C.

During installation it must be made sure that the ventilation grid is NOT covered. Once

the shelf has been installed, it must be checked that the ventilation grid on the top is NOT

obstructed in any way.

When installing the terminal in a frame of a cabinet, in order to improve ventilation, a

space equivalent to at least one standard unit must be left above and below it.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

7/69

1.1 SHELF MODULE CAPACITY

The shelf can hold up to 13 modules, of which, only that of power supply (or the two

power-supply modules in the case of secondary power-supply) and that of processing have

a fixed position. The rest of the modules (line interface, protection-side interface, relay

interface and those related to the remote measurements application) can be inserted in any

position of the shelf, see Figure 2.

Figure 2 Internal rear view of the TPU-1 shelf

The correspondence between connectors and slots should be taken into account when

establishing the constitution of the equipment, from the Management System, in order to

carry out configuration. It is therefore necessary to indicate the slots one wishes to configure

and the type of module associated with each one, in the corresponding programming page.

The modules are inserted in the shelf with the help of the two handles on the front plate.

The following section describe the procedure for replacing modules.

A module must NOT be replaced whilst the terminal power-supply is connected.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

8/69

1.2 REPLACING THE MODULES

In order to replace a module in the shelf, the operations indicated below should be carried:

1. Release the two fixing screws of the module.

Depending on the type of module, the earth cable is attached to the upper screw. In that

case, disconnect it.

2. Extract the module by means of the handles.

3. Depending on the type of module, extract the connector.

The earth cable of the module was disconnected in point 1.

Once the module is inserted in the shelf, tighten the module to the chassis and, if

necessary, attach the earth cable to the upper screw.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

9/69

2 FRONT PLATE ELEMENTS

The TPU-1 terminal has twenty-five LEDs on the front plate. The LEDs identified as

PRIMARY and SECONDARY are associated with the terminal power supply. The

PHYSICAL LINK LEDs indicate the interface type being active, and the LEDs identified as

TP 1 and TP2 are associated with the two possible communication channels that can

manage the terminal and to the command transmission and reception circuits.

The front plate also has an USB connector that is for Pweb management(

). It can also have

an optional LCD display which allows certain parameters of the terminal to be monitored,

see Appendix D, without having to access the Management System.

Figure 3 and Figure 4 show the signalling of the different LEDs, and Figure 5 describes the

optional LCD display.

Figure 3 Signalling of LEDs (I)

(

)Local management system based on a Web interface. The Pweb management, given that it requires a web server external to

the terminal, is known as External Web Management.

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1

INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

10/69

Figure 4 Signalling of LEDs (II)

Figure 5 Optional LCD display

Inhaltsverzeichnis

Andere DIMAT Touch-Terminal Handbücher

DIMAT

DIMAT OPU-1 Bedienungs- und Wartungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung